2026 BMW X7
2 recalls and 0 owner complaints on record for this model year.
Check a specific vehicle
This page describes the model. To see how one particular car is equipped, and whether its identifier is valid, decode its VIN.
Decode a VIN2 recalls and 0 owner complaints on record for this model year.
This page describes the model. To see how one particular car is equipped, and whether its identifier is valid, decode its VIN.
Decode a VINAlmost all of this describes the model year, not the individual car. Nothing here can tell you about this vehicle’s mileage, accidents or ownership — no identifier encodes those.
BMW of North America, LLC (BMW) is recalling certain 2026 X6, X7, X5, and X5 Plug-In Hybrid vehicles. The instrument panel may have been manufactured incorrectly and prevent the passenger-side air bag from deploying properly.
Remedy: Dealers will replace the instrument panel trim, free of charge. The vehicles have not been sold from dealer inventory and therefore, no owner letters will be mailed. Owners may contact BMW customer service at 1-800-525-7417. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on December 4, 2025.
BMW of North America, LLC (BMW) is recalling certain 2026 X5 Plug-in Hybrid, X5, and X7 vehicles. The windshield may not be sealed properly, which can allow water to enter the power distribution box or electronic control unit.
Remedy: Dealers will inspect the windshield seal. If any leaks are detected, the seal will be repaired and vehicle control units and wiring will be replaced as necessary, free of charge. Owner notification letters were mailed December 3, 2025. Owners may contact BMW customer service at 1-800-525-7417.
Published by model year, not by VIN — may not apply to this vehicle, or may already have been done. Confirm with a dealer.
Water may come into contact with the starter relay and gradually cause corrosion. This could affect the electrical connection inside the relay and make the engine difficult to start. It may also result in a short circuit and could cause the starter to overheat leading to a fire when the vehicle is in motion or when it is parked with the ignition off. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The engine starter’s electrical contacts may overheat and cause the vehicle to start improperly. Continued starting attempts can intensify the overheating and ignite surrounding components, potentially leading to a vehicle fire while driving or shortly after parking. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The hollow shaft of the servomotor was not welded correctly. The weld may not be able to withstand high braking pressure build-up and may break. In this case, the reduced braking performance requires greater force and the braking distance may increase. In addition, the ABS and DSC brake control systems are not assisted. This increases the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The software-based overload protection function cannot sufficiently prevent the starter being overloaded in the event of repeated long start-up attempts. The starter may overheat or sparks may be produced as a result of an increased current flow. This increases the risk of a fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The gas generator in knee airbag modules was not properly inserted into the air cushion, resulting in the cushion failing to unfold sufficiently. As a result, it may not be able to deploy correctly in the event of an accident, leading to a reduction in the restraint effect, increasing the risk of injury to the occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The integrated braking system could be compromised, which could lead to an unexpected failure of the hydraulic braking assistance, thereby requiring greater pressure on the brake pedal. This can result in a longer braking distance, as well as failure of the Anti-lock Braking System (ABS) and the Dynamic Stability Control (DSC), increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The dashboard in the affected vehicles may not have been manufactured to the manufacturer specifications. In the event of anaccident, the passenger side airbag may not deploy as intended which could increase the risk of injury to the frontpassenger. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Matched on brand and model name — Safety Gate publishes no VIN. Check the production dates, and quote the recall code to a dealer.