2020 BMW X7
12 recalls and 52 owner complaints on record for this model year.
Check a specific vehicle
This page describes the model. To see how one particular car is equipped, and whether its identifier is valid, decode its VIN.
Decode a VIN12 recalls and 52 owner complaints on record for this model year.
This page describes the model. To see how one particular car is equipped, and whether its identifier is valid, decode its VIN.
Decode a VINAlmost all of this describes the model year, not the individual car. Nothing here can tell you about this vehicle’s mileage, accidents or ownership — no identifier encodes those.
BMW of North America, LLC (BMW) is recalling certain 2020 340I, X6, 2020-2025 840I, 2020-2022 740LI, 2019-2020 X7, and X5 vehicles. After repeated attempts, the starter motor may overheat from an electrical overload.
Remedy: Dealers will replace the engine starter, free of charge. This recall includes vehicles repaired under recall 24V576 and those owners will need to have their vehicle repaired again. Owner notification letters were mailed February 9, 2026. Owners may contact BMW customer service at 1-800-525-7417. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov November 17, 2025.
BMW of North America, LLC is recalling certain 2019-2020 X5, X7, 2020 3 Series Sedan, X6, 2020-2021 7 Series Sedan, 2020 8 Series Convertible, 8 Series Coupe, and 2020 8 Series Gran Coupe vehicles. Please see the recall report for the complete list of models. In the event the starter motor fails, repeated attempts to start the vehicle can cause the starter motor to overheat from an electrical overload.
Remedy: Dealers will update the vehicle software, free of charge. Owner notification letters were mailed September 27, 2024. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2019-2022 BMW X7 xDrive40i, X7 Drive50i, X7 M50i vehicles with third-row seats. One or more of the compression springs that lock the backrest may not have been installed properly, and could dislodge or detach.
Remedy: Dealers will inspect the third-row seat and, if necessary, remove and reinstall improperly installed compression springs, and reinstall any missing springs, free of charge. Owner notification letters were mailed November 4, 2022. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2022 4 Series Gran Coupe (430i, 430i xDrive, M440i xDrive); 2019-2022 X5 sDrive40i, X5 xDrive40i, X5 xDrive50i, X5 M50i, X5M; 2021-2022 X5 xdrive45e; 2020-2022 X6 sDrive40i, X6 xDrive40i, X6 xDrive50i, X6M and 2019-2023 X7 xDrive40i, X7 xDrive50i, X7 M50i, X7 xDrive60i, X7 M60i, X7M, Alpina XB7 vehicles. The roof function control unit may be programmed incorrectly, allowing the sunroof to close without the key fob present inside the vehicle. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 118, "Power-Operated Window Systems."
Remedy: Dealers will reprogram the roof function control unit, free of charge. Owner notification letters were mailed June 20, 2022. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2019-2021 X3 sDrive30i, X3 xDrive30i, X3 M40i, X3M, X4 xDrive30i, X4 M40i, M550i, X4M, X5 sDrive40i, X5 xDrive40i, X5 xDrive50i, X5M, X5 M50i, X7 xDrive40i, X7 xDrive50i, X7 M50i, Alpina XB7, 330i, 330i xDrive, M340i, M340i xDrive, and 8 Series Coupe, Convertible and Grand Coupe, 840i, 840i xDrive, M850i xDrive, M8, 2020-2021 530e, 530e xDrive, 330e, 330e xDrive, 745Le, 745Le xDrive, X5 xDrive45e, X3 xDrive30e, X6 sDrive40i, X6 xDrive40i, X6 xDrive50i, X6 M50i, X6M, 530i, 530i xDrive, 540i, 540i xDrive, M550i xDrive, M5, 740i, 740Li, 740Li xDrive, M760i Drive, M760Li xDrive, 750Li xDrive Alpina, Alpina B7 xDrive, and 2021 4 Series Coupe 430i, 430i xDrive, M440i xDrive vehicles. When shifting into Reverse, a small portion of the rearview image may be obscured, or the screen may not illuminate. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 111, "Rear Visibility."
Remedy: BMW will notify owners, and dealers will inspect the rearview camera software and update it if necessary, free of charge. The recall began April 16, 2021. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2020-2021 8 Series Coupe, Grand Coupe and convertible 840i, 840i xDrive, M850i xDrive, M8 and 740 Li, 740 Li xDrive, 750 Li xDrive, M760 Li xDrive, X6 sDrive40i, X6 xDrive40i, X6 xdrive50i, X6 M50i, X6M, and 2019-2021 X5 sDrive40i, X5 xDrive40i, X5 xDrive50i, X5 M50i, X5M, X7 xDrive40i, X7 xDrive50i, X7 M50i, and 2021 M3, M3 Competition, M4 Coupe, M4 Competition Coupe, X5 xDrive45e, 745 Le xDrive. The rotor and shaft within the integrated brake system may not have been welded properly and could separate during a hard braking event, possibly resulting in a loss of the Antilock Brake System (ABS) and braking assistance.
Remedy: BMW will notify owners, and dealers will replace the integrated brake system, free of charge. Owner notification letters were mailed on May 25, 2021. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2020 X5 sDrive40i, xDrive40i, X5 M50i, X5M, X7 xDrive40i, X7 M50i, X6 xDrive40i, X6 M50i and X6M vehicles and 2021 X5 xDrive45e vehicles. The weld between the front axle support and the right front control arm bearing bracket may separate.
Remedy: BMW will notify owners, and dealers will replace the front axle support, free of charge. The recall began December 18, 2020. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2020-2021 X5 sDrive40i, xDrive40i, xDrive50i, X5 M50i, X5M, X6 sDrive40i, xDrive40i, X6 M50i, X6M, X7 M50i and 2021 X5 xDrive45e vehicles. The headlamps may allow a blue light to illuminate. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 108, "Lamps, Reflective Devices, and Associated Equipment."
Remedy: BMW will notify owners, and dealers will inspect the headlamps and, if necessary, replace them, free of charge. The recall began October 30, 2020. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2020 X5 sDrive 40i, X5 xDrive 40i and one X7 xDrive 40i vehicle. The starter motor may have an extra bolt that could potentially fall into the transmission housing and cause an engine stall.
Remedy: BMW will notify owners, and dealers will inspect the starter motor for the extra bolt, removing it if necessary. Dealers will also inspect the starter for damage, and check if the bolt has fallen into the transmission housing, replacing any damaged parts as necessary. All repairs will be performed free of charge. The recall began on October 2, 2020. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2020 X7 xDrive40i and X7 xDrive50i vehicles. The rear reflex reflectors may not reflect an adequate amount of light. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment."
Remedy: BMW will notify owners, and dealers will replace both rear reflex reflectors, free of charge. The recall began March 30, 2020. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2018 540d, 2018-2020 530i, 530i xDrive, 540i, 540i xDrive, M550i xDrive, M5, 530e, 530e xDrive, X3 sDrive, X3 xDrive, X3 M40i, X3 M, and 2019-2020 X4 xDrive, X4 M40i, X4 M, X7 xDrive, X7 M50i, 740Li, 740Li xDrive, 750Li, 750Li xDrive, 8 Series Convertible and Coupe 840i, 840i xDrive, M850i xDrive, X5 sDrive, X5 xDrive, X5 M50i, X6 xDrive, X6 M50i, 330i, 330i xDrive, M340i, M340i xDrive, Z4 sDrive, Z4 M40i, 740Le xDrive and 745Le xDrive, 2018-2019 640i xDrive Gran Turismo and Rolls-Royce Phantom, 2019 M850i xDrive Gran Coupe and Rolls-Royce Cullinan and 2020 Toyota Supra vehicles. The back-up camera and display settings can be adjusted such that the rear view image is no longer visible and the system will retain that setting the next time the vehicle is placed in reverse. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 111, "Rearview Mirrors."
Remedy: BMW will notify owners, and dealers will update the back-up camera software, free of charge. The recall began November 8, 2019. Owners may contact BMW customer service at 1-800-525-7417 or Rolls-Royce at 1-877-877-3735. Toyota owners may contact Toyota customer service at 1-888-270-9371.
BMW of North America, LLC (BMW) is recalling certain 2020 X5 sDrive40i, X5 xDrive40i, X5 M50i, X7 xDrive40i and X7 M50i vehicles. The steering rack pinion teeth may break under load, resulting in a loss of steering control.
Remedy: BMW will notify owners, and dealers will replace the steering rack, free of charge. The recall began August 21, 2019. Owners may contact BMW customer service at 1-800-525-7417.
Published by model year, not by VIN — may not apply to this vehicle, or may already have been done. Confirm with a dealer.
Water may come into contact with the starter relay and gradually cause corrosion. This could affect the electrical connection inside the relay and make the engine difficult to start. It may also result in a short circuit and could cause the starter to overheat leading to a fire when the vehicle is in motion or when it is parked with the ignition off. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The engine starter’s electrical contacts may overheat and cause the vehicle to start improperly. Continued starting attempts can intensify the overheating and ignite surrounding components, potentially leading to a vehicle fire while driving or shortly after parking. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The hollow shaft of the servomotor was not welded correctly. The weld may not be able to withstand high braking pressure build-up and may break. In this case, the reduced braking performance requires greater force and the braking distance may increase. In addition, the ABS and DSC brake control systems are not assisted. This increases the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The software-based overload protection function cannot sufficiently prevent the starter being overloaded in the event of repeated long start-up attempts. The starter may overheat or sparks may be produced as a result of an increased current flow. This increases the risk of a fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The gas generator in knee airbag modules was not properly inserted into the air cushion, resulting in the cushion failing to unfold sufficiently. As a result, it may not be able to deploy correctly in the event of an accident, leading to a reduction in the restraint effect, increasing the risk of injury to the occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The integrated braking system could be compromised, which could lead to an unexpected failure of the hydraulic braking assistance, thereby requiring greater pressure on the brake pedal. This can result in a longer braking distance, as well as failure of the Anti-lock Braking System (ABS) and the Dynamic Stability Control (DSC), increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The dashboard in the affected vehicles may not have been manufactured to the manufacturer specifications. In the event of anaccident, the passenger side airbag may not deploy as intended which could increase the risk of injury to the frontpassenger. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Matched on brand and model name — Safety Gate publishes no VIN. Check the production dates, and quote the recall code to a dealer.
• Third-row seat in my 2020 BMW X7 failed during normal operation and trapped my [XXX] daughter between the seatbacks. • She sustained injuries to her legs (documented in photos). I injured my arm while trying to free her. • Approximately 10 people witnessed the incident. • Seat would not move or release electronically or manually—no functional emergency release. • Multiple BMW system warnings occurred before the incident, including: – “Third row seat risk of injury” – “Right/left rear seat unlocked” – “Right/left rear seat back unlocked” • BMW’s inspection found the passenger-side third-row seat motor housing broken. • There was no misuse and the failure occurred during normal operation • BMW refuses to repair the defect under warranty and attempted to return the vehicle unrepaired. • BMW suggested an “outside influence,” but evidence does not support this. • This defect creates a serious entrapment and injury hazard with no reliable manual release. • Requesting NHTSA investigation into BMW X7 third-row seat motors, locking mechanisms, and lack of emergency release due to risk of occupant injury or inability to evacuate a trapped passenger. There is an open and unresolved case with the manufacturer. Please help us and others that may be in danger. We still don’t have our vehicle back after 6 weeks and they state they will not fix it and return it to us broken, unsafe, and not usable. Here is the contact at BMW Gabrielle Dorcean Executive Customer Care, Customer Relations and Services BMW of North America, LLC Phone: [XXX] [XXX] Email: gabrielle.dorcean@bmwgroup.com INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
I am filing this complaint because the third-row passenger seat in my 2020 BMW X7 has a serious defect that poses an immediate safety risk to children and passengers. The third-row seat malfunctioned while my child was exiting the vehicle. The powered seat began moving unexpectedly and trapped my child’s leg, and we had extreme difficulty getting the seat to release. This is an extremely dangerous failure for any powered seat, especially one that is frequently used by children. This is not normal wear and tear — this is a mechanical and electrical failure of a safety-critical seat system. BMW Fresno has had the vehicle for more than six weeks and cannot fix the problem. BMW North America reviewed the case but denied responsibility and closed it, even though the defect affects a powered safety-critical seat. We still have no repair, no explanation, and no assurance that the seat is safe. I am filing this because the powered seat poses a clear risk of injury, and BMW has not resolved or acknowledged the safety defect. I request that NHTSA investigate the 2020 BMW X7 third-row seat system for potential entrapment hazards. Actions Taken •BMW Fresno inspected the vehicle and kept it for 6+ weeks. •BMW NA conducted a review but has refused to cover cost of repair or acknowledge a defect. •I am seeking NHTSA’s involvement because this is a clear safety problem that BMW has not corrected.
On October 21, 2021 we purchased a 2020 BMW X7 from West Houston Land Rover (AutoNation) in Oct 2021. Purchased extended warranties. Within 3 months: Technicians advised replacing nearly new tires. Car smoked on highway after oil change, dismissed as spilled oil. Nov 28, 2023: Car burst into flames 5 minutes after oil change and passed multipoint inspection. Car burned completely to the ground Escaped unharmed but met with rudeness and dismissal from dealership. GM initially promised help, then stopped communication after seeing evidence. Unacceptable: Horrific experience with fire and previous issues. Appalling service and intimidation tactics (threat of lawsuit for sharing story). We demanded immediate action to reimburse our losses and hold the dealership accountable. We will actively share our story to warn others. When I did mention about sharing this experience with consumers the GM said Autonation would sue us for slander if we put any information about this event online. [XXX] Fire started under the hood (engine) [XXX] (owner) was driving a car that was burning it could have exploded or killed her while driving. Also other vehicles were put in danger while driving near a burning flaming car. I do not know if anyone has reproduced this. the following are researching this by investigating: Geico insurance We were told the dealer also filed an insurance claim (not verified as no info was provided) BMW communicated they would also view the car and do an investigation Police were on the scene Fire dept was on the scene and put the fire out No warning lights, no vehicle warning, just burst into flames while driving home from the oil change I have pictures/video/copy of multipoint inspection performed 5 min before the fire started, as well as a receipt for the oil change/multipoint inspection as well as all communications with the GM. The website is not allowing upload of files INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
On 11/23/2021 while driving the computer screen stated malfunction with personal protection device with in 10 seconds the rear of the car burst into flames the fire inspector from our insurance company traced the cause of the event to the fuse box neither BMW or the dealership will take any responsibility this car had never been repaired and only authorized dealership did yearly service
The BMW X7 caught on fire going down the HW.
NHTSA COMPLAINT (VERY IMPORTANT – SAFETY FOCUSED) Subject: Safety Complaint – BMW X7 Electrical Defect and Fire Risk (VIN: [XXX] ) To the National Highway Traffic Safety Administration, I am submitting a formal safety complaint regarding a 2020 BMW X7 xDrive40i affected by Recall No. 24V-576 (Engine Starter Defect). My vehicle has experienced: •Sudden battery failure •Electrical system malfunction •Starter-related issues consistent with recall description BMW’s recall states that the defect can cause: •Electrical overload •Starter overheating •Increased risk of engine compartment fire This is not a theoretical issue—I have already experienced a complete system failure requiring towing and major repair, placing my family and me at risk. Serious Concerns •The defect appears systemic and dangerous •The remedy (software update) does not appear sufficient •The failure occurred without adequate warning Request for Investigation I urge NHTSA to: 1.Investigate the effectiveness of BMW’s recall remedy 2.Determine whether additional defects exist in the electrical system 3.Ensure BMW provides a permanent and safe solution This issue poses a serious public safety risk, and stronger regulatory action may be necessary. Sincerely, DLAA REAL ESTATE INVESTMENT, LLC, [XXX] and [XXX] ), regarding the defective BMW, YEAR 2020, MODEL: X7 xDrive40i | COLOR: OC27 ARCTIC GREY METALLIC VIN: [XXX] | CELL: [XXX] | FAX: [XXX] [XXX] | [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
ON TUESDAY, NOVEMBER 17TH, AROUND 7PM ET, I PARKED IN FRONT OF A BUILDING COMPLEX. THE CAR WAS IN PARKING MOD WITH ENGINE ON. I WAS TALKING TO MY BROTHER IN LAW IN THE CAR WHEN WITHIN 4-5 MIN FROM THE TIME OF THE CAR WAS IN FULL STOP, WE HEARD THE ENGINE ROARING LOUDER AND LOUDER AND THE CAR ACCELERATED WITH TREMENDOUS SPEED TOWARDS THE BUILDING (PARKING SPOT IS AROUND 20 FEET FROM THE BUILDING). I PRESSED THE BRAKES, BUT THE CAR DIDN'T STOPPED UNTIL WE ENDED UP INSIDE THE BUILDING GOING THROUGH A BRICK WALL. THE ENGINE WAS STILL ROARING LOUDER FOR FEW MORE MINUTES WITH FRONT WHEELS SPINNING AROUND, UNTIL THE CAR SHUTS DOWN COMPLETELY. FROM ALL THAT IMPACT NO AIRBAG WAS OPEN, COALITION SENSORS DIDN'T STOP THE CAR, NOT EVEN ME PRESSING THE BREAKS DIDN'T STOP THE CAR. AFTER THE INCIDENT OUR INSURANCE (FARM BUREAU) AND THE MANUFACTURE (BMW USA) WAS CONTACTED IMMEDIATELY. AFTER ALL THIS TIME OF THEIR "INVESTIGATION", THE BMW REPRESENTATIVE CONTACTED US ON FRIDAY, DECEMBER 18TH. TELLING US THAT THEY HAVE NOT FOUND ANY DATA IN THE CAR (AFTER THEY PERFORMED ALL TESTS...) TO SUPPORT OUR CLAIM AND THAT THE CAR (THE BLACK BOX) HAS NOT RECORDED THIS ACCIDENT. WHAT I EXPERIENCE ON THIS CAR IS REAL AND I THANK GOD EVERY DAY THAT I WASN'T IN A HIGHWAY OR WITH MY KIDS IN THE CAR AT THAT TIME. THIS CAR HAS TO BE INVESTIGATED FURTHER AS IT IS NOT SAFE
We came from [XXX] to [XXX] at night. It was rainy in [XXX]. We parked the vehicle in the front of the garage door of the house and went to sleep. Around 8:00-9:00AM two police cars from [XXX] PD came to our house. The officer said that the vehicle calls to BMW or 911 as an emergency and they forwarder that call to FPD. The officers checked the vehicle and they figured that the vehicle did the emergency call when was parked. Now, the emergency call system is not working, because of the bad factory sealant in the top of the roof and the water leaks exactly to the Telecomunication module (TCM). INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
Low oil sensor continues to light up and says i am low on oil. Found out that my oil pump was the main cause of the issue. At this time I have to have the oil pump replaced. It was also determined there have been numerous reports regarding oil pump failure in the 2020 BMW x7 due to an internal plastic part.
The front thrust arm bushing was previously replaced on December 19, 2023, at 34,750 miles (after three years of ownership). It has now failed again at 57,203 miles, lasting only about 22,500 miles. This repeat failure within a relatively short timeframe and mileage interval suggests an underlying issue or defective part. The dealer wants me to replace both Front Thrust Arm bushings again.
My X7’s front differential went bad at 50k miles. I paid over 100k for a vehicle of this caliber to have something like this fail and have to pay 8k with no help from BMWNA. I’ve been a loyal customer with bmw having owned over 5 bmw vehicles in the past. And for me to get treated like this is unacceptable. I hope we can have a law suit against bmw for this.
While driving the vehicle sensor lights began to come on. I assumed it was a dirty outside sensor. Not long after the ABS system lit up and my car said traction even though I was just pulling into my driveway. I quickly turned around and drove to my mechanic. Showed him all the lights and he connected the computer to read the error codes. Found out that my oil pump was the main cause of the issue. Double checked to make sure it wasn't a battery failure causing incorrect error codes and the battery was in good condition. At this time I have to have the oil pump replaced. It was also determined there have been numerous reports regarding oil pump failure in the 2020 BMW x7 due to an internal plastic part.
I am writing to formally report a potential safety-related defect involving BMW vehicles equipped with the B58TU engine, primarily affecting model years 2019 through 2021. My vehicle experienced a sudden loss of engine oil pressure that resulted in catastrophic engine failure. This condition occurred with little to no warning and led to immediate vehicle disablement. The failure created a hazardous situation, as the vehicle was no longer able to maintain propulsion and could have placed occupants at risk because it occurred in active traffic or unsafe conditions. Based on my experience and additional research, the issue appears to originate from the engine’s oil pump design. Specifically, the oil pump contains an internal pressure-regulating component originally manufactured from plastic. This component is prone to fracturing, particularly during cold starts or low ambient temperatures. When this failure occurs, oil pressure becomes erratic or is lost entirely, often without sufficient warning to prevent engine damage or vehicle shutdown. My vehicle had this occur on January 20th 2026, as it was 5 Degrees outside. I suddenly lost oil pressure and had my vehicle’s engine catastrophically fail on a highway with my two small children ages (3) and (7 months) in the vehicle. In some cases, drivers may observe warning signs such as inability to measure oil level electronically, abnormal oil pressure readings, or drivetrain malfunction warnings. However, these indicators are inconsistent and often appear only moments before complete failure, leaving insufficient time for corrective action. This issue represents a significant safety concern for the following reasons: * Sudden loss of oil pressure can result in immediate engine shutdown or loss of propulsion while driving * Failures frequently occur under predictable conditions (cold starts in low temperatures), indicating a repeatable defect * Drivers are not provided with adequate warning to safely respond before damage.
I'm reporting a safety issue with BMW vehicles equipped with the B58TU engine, primarily 2019-2021 models. These vehicles have an oil pump with an internal plastic component that regulates oil pressure, and this part is fracturing in the field, causing sudden loss of oil pressure. The failure typically occurs during cold starts in low temperatures. When it fails, oil pressure becomes erratic or is lost entirely, often with little to no warning before engine damage or vehicle disablement. Warning signs, when present, include inability to measure oil level electronically, abnormal oil pressure, or sudden drivetrain malfunction warnings. These can rapidly progress to engine shutdown or severe damage from oil starvation. This creates a dangerous situation because the vehicle can become disabled without warning while driving or after startup. This is especially hazardous when cars become immobilized in traffic or during winter conditions when failures occur most frequently, leaving occupants exposed to freezing temperatures while awaiting assistance. Pump replacement requires extensive disassembly and commonly costs $6,000-$8,000, assuming no engine damage. A critical concern: owners cannot determine if their vehicle has the original plastic pump or the later metal revision. BMW's VIN-based parts lookup now shows updated components even when original plastic parts remain installed, and BMW has removed the original plastic part number from dealer networks entirely. Failures are reported across multiple production years, and the scope of affected vehicles remains unclear. Because this condition causes sudden vehicle disablement without adequate warning, especially in cold weather, I believe this warrants investigation as a potential safety-related defect.
The transfer case on my 2020 BMW X7 failed and had to be replaced. Turning the vehicle became unstable as the vehicle shuttered badly. BMW confirmed the shuttering and first changed the transfer case fluid. However, it only slightly helped at first but the shuttering came fully back shortly thereafter. The vehicle was inspected by BMW twice. I don’t remember any warning lights on the dash. The shuttering first occurred in 2024.
Filed by owners of this model year and unverified by NHTSA — one person’s account, not an established fact.