2024 BMW X3
3 recalls and 36 owner complaints on record for this model year.
Check a specific vehicle
This page describes the model. To see how one particular car is equipped, and whether its identifier is valid, decode its VIN.
Decode a VIN3 recalls and 36 owner complaints on record for this model year.
This page describes the model. To see how one particular car is equipped, and whether its identifier is valid, decode its VIN.
Decode a VINAlmost all of this describes the model year, not the individual car. Nothing here can tell you about this vehicle’s mileage, accidents or ownership — no identifier encodes those.
BMW of North America, LLC (BMW) is recalling certain 2024-2026 X3 sDrive30i, X3 30 xDrive, and X3 M50 xDrive vehicles. The steering spindle may have been incorrectly attached to the steering column.
Remedy: Dealers will inspect the steering connection and replace hardware or replace the spindle and column, as necessary, free of charge. Owner notification letters are expected to be mailed October 2, 2026. Owners may contact BMW customer service at 1-800-525-7417. Vehicle Identification Numbers (VINs) involved in this recall will become searchable on NHTSA.gov beginning October 2, 2026.
BMW of North America, LLC (BMW) is recalling certain 2022-2024 X3 sDrive30i and X3 xDrive30i vehicles. The second-row seat side door locking modules may not function properly and allow the doors to be unlocked with a single motion. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 206, "Door Locks and Door Retention Components."
Remedy: Dealers will replace the second-row seat side door locking modules, free of charge. A letter informing owners of the safety risk was mailed on April 21, 2025. Owners may contact BMW customer service at 800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2024 2 Series Coupe (230i), 330i, X3 sDrive30i, X3 xDrive30i, X3 M40i, and X4 xDrive30i, X4 M40i vehicles. The steering gear may not have been tightened properly, which can allow it to loosen.
Remedy: Dealers will replace the steering gear, free of charge. Owner notification letters were mailed January 11, 2024. Owners may contact BMW customer service at 1-800-525-7417.
Published by model year, not by VIN — may not apply to this vehicle, or may already have been done. Confirm with a dealer.
Water may come into contact with the starter relay and gradually cause corrosion. This could affect the electrical connection inside the relay and make the engine difficult to start. It may also result in a short circuit and could cause the starter to overheat leading to a fire when the vehicle is in motion or when it is parked with the ignition off. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Due to a manufacturing failure, the protection of the two outer headrests in the second row is reduced. In the event of a collision or accident, passengers could be injured. In addition, headrest parts may become exposed and also cause serious injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The RSW22 starter with reinforced water tightness (RWT) may experience increased abrasion of the magnetic contact, causing deposits to build up at the lowest point inside the relay. These deposits may increase relay contact resistance, leading to starting failures or short circuits. If a short circuit occurs, either when attempting to start the vehicle or while driving due to vibration-related movement of the deposits, it could cause a thermal event and increase the risk of fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Damaged brake discs may have been fitted to the front axle. This can lead the brakes to fail when a heavy load is placed on the wheel concerned, increasing the risk of accident and injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Failure to bolt the plus voltage (B+) cable tightly enough to the starter generator may result in contact problems and an increase in contact resistance at the bolted connection. This may in turn lead to local overheating and the vehicle catching fire or to the engine stalling while the vehicle is coasting. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The positive battery cable of the starter-generator may not have been manufactured correctly. This could result in a loose electrical connection, leading to excessive contact resistance. The vehicle cannot charge or start. Contact points in the starter-generator could overheat and cause a vehicle fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the inflator of the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments of the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The driver airbag inflator may malfunction due to long-term degradation. In this case, if the airbag is deployed in an accident, the internal pressure in the inflator may be too high. The inflator could burst. Metal fragments may cause injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The failure concerns the RSW22 starter, type RWT (reinforced for watertightness). Increased abrasion of the magnetic contact can lead to the formation of deposits at the lowest point of the relay interior. This in turn can increase the resistance of the relay contact, causing accidental ignition or even short circuits, possibly leading to a thermal reaction and fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The failure concerns the RSW22 starter, type RWT (reinforced for watertightness). Increased abrasion of the magnetic contact can lead to the formation of deposits at the lowest point of the relay interior. This in turn can increase the resistance of the relay contact, causing accidental ignition or even short circuits, possibly leading to a thermal reaction and fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The failure concerns the RSW22 starter, type RWT (reinforced for watertightness). Increased abrasion of the magnetic contact can lead to the formation of deposits at the lowest point of the relay interior. This in turn can increase the resistance of the relay contact, causing accidental ignition or even short circuits, possibly leading to a thermal reaction and fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The steering system sensor may malfunction causing an unintended steering movement of the vehicle. This increases the risk of accidents and injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The screw connection of the servo unit on the gear rack casing of the steering system may be faulty. This could cause the steering system to fail and become blocked, increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Due to faulty rear-most screws, the screw fixings of the boot's lashing rails can fail in the event of a rear-end collision with heavy intrusion and penetrate the backs of the rear seats. This increases the risk of injury to the occupants of the rear seats. The vehicles concerned have already been modified in connection with the recall code 0051960500. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant within the integrated inflator of driver airbags can deteriorate during time. If the airbag deploys, it could result in fragments from the inflator casing injuring the vehicle’s occupants. The product does not comply with the Regulation on the approval and market surveillance of Motor Vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Due to faulty rear-most screws, the screw fixings of the boot's lashing rails can fail in the event of a rear-end collision with heavy intrusion, and penetrate the backs of the rear seats. This increases the risk of injury to the occupants of the rear seats. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
A seam on the inflator housing of the driver airbag may not have been correctly welded. In case of accident, when the airbag is deployed, the inflator can burst, releasing metal parts which could cause injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The driver's airbag inflator propellant may deteriorate over time. If activated during an accident, excessive internal pressure may cause the inflator to burst, and metal fragments could pass through the cushion material causing injury to occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Due to a manufacturing error, the weld seam of the integrated transmission control unit (ITCU) may not have been correctly executed. As a result, transmission oil could leak into the ITCU, causing it to fail. This may lead to transmission seizure, increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Matched on brand and model name — Safety Gate publishes no VIN. Check the production dates, and quote the recall code to a dealer.
The contact owned a 2024 BMW X3. The contact stated that while driving at approximately 35 MPH and turning right, the vehicle unintentionally continued accelerating and veering to the right. The contact stated that she had depressed the brake pedal, but the brakes did not respond. The contact stated that the vehicle jumped the curb, the contact was not able to steer the vehicle back onto the roadway because the steering wheel was seized. The contact stated that the vehicle hit a traffic sign and side-swiped a street light pole. The contact stated that the vehicle then crashed into a parked vehicle head-on and stopped. The contact stated that the air bags had not deployed during the front-end collision. The contact stated that the police and emergency services had arrived. The contact was transported to a hospital, and the police issued a report. The contact stated that she had bruises on her chest, ribs, both arms, and wrists. The contact also had a whiplash injury to her neck. The vehicle was towed to an impound lot, and a total loss was declared. The manufacturer was informed of the failure. The failure mileage was approximately 17,000.
[XXX] old infant's face was cut and bleeding from the Chicco Fit360 ClearTex Rotating Car Seat's safety straps with included pads INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
I started to pull forward from a pharmacy drive-through at an intended low speed (approximately10/15 mph) for a right turn onto a driveway. The car was on auto-hold and in drive gear. When I turned right, the vehicle went into a full throttle acceleration and continued until impact. Brakes were totally ineffective. A TWO-LINE BRIGHT YELLOW MESSAGE FLASHED IN THE INSTRUMENT PANEL, "TRANSMISSION MALFUNCTION". There was no automatic braking or forward collision function. I made a hard left turn in about 40 feet to avoid a shopping center parking lot. The vehicle continued until colliding with a concrete filled bollard and an automotive electric charging station. The vehicle charging at this station was also struck. My vehicle fell back, landing on its right side. The driver's airbag and both side curtains deployed. I was left suspended in the seat belt until the Fire Department, Emergency Services and the Highway Patrol arrived. A Jaws of Life was used to open the sunroof and extract me. I was transported by ambulance to an emergency treatment center. I was examined there and imaging done. I sustained a ruptured tendon in the middle right finger (permanent damage) and sagittal band ruptures in two fingers on that hand. There were numerous scrapes and bruises on the left thigh, both forearms and hands as well as minor cuts on my forehead. Also, post -accident, I experienced neck pain and overall soreness for several days due to whiplash. The Event Data Recorder was unattainable as insurance paid the claim for the totaled car within one week and assumed ownership. According to the salvage yard, it was sold shortly thereafter. Refer to NHTSA ID number 11659896 for this issue with another 2024 BMW x3 Photos to accompany complaint will be sent by email with VIN #
Driving on the highway, unexpectedly i was not able to turn anymore. On the road was something I wanted to not hit, but steering did not work as usual. The car was forced to the left into the wall and the only thing i was able to do was using the breaks steady and slowly. Steering in the other direction did not work and in the end i hit the divider wall on the left shoulder
As I was pulling into a parking stall at work, I pressed on the brake and the vehicle did not stop. It went up over the sidewalk which is stepped up from the parking lot 4-6". i continued to press the break in as far as I could and the vehicle continued to travel at least 20 and stopped when it hit the building. The vehicle is equipped with the automatic emergency breaking and collision warning in which neither worked. The brick on the building was only scrapped. However, there are windows right at the brick line at the location that my car stopped. The car did not go through the window or the building. If it would have, it could have injured those inside. I was pressing on the breaks so hard that I have an injury to my toe. I have not seen a doctor yet, but it's possible that I broke it as I was pressing that hard. The vehicle has not been inspected by the insurance company, manufacturer, or dealership yet. I called the dealership and asked that it be inspected and a diagnostic run immediately. The dealership said they cannot get me in for a week. My vehicle is equipped with a Event Data Recorder.
The contact owns a 2024 BMW X3. The contact received notification of NHTSA Campaign Number: 26V438000 (Electrical System); however, the part to do the recall repair was not yet available. The dealer was not contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue and confirmed that parts were not yet available. The contact had not experienced a failure.
I was pulling out of a parking spot and my X3 completely stalled and lost power. I got infomation on my screen to take my car to my dealer as soon as possible. I was able to start and drive it home. The following week I took it to the dealer for the problem. My local BMW dealer has had my X3 since July 27th over 2 weeks. They said they waiting for a code or fix for what happened. I don’t know if it’s a power train or engine problem. My X3 only has 21,000 miles on it. My concern is this problem could have happened on highway and I could have had a different outcome.
Since purchasing my vehicle, I have experienced numerous ongoing issues that BMW has failed to address. The problems include: A squealing and beeping noise coming from the engine. The headlights turning on by themselves. Interior lights turning on without warning. The vehicle shaking while driving. The check engine light repeatedly coming on. A recent gasoline smell that required me to take the vehicle to the shop due to safety concerns. The roof making a popping noise when driving over uneven driveways or surfaces. I have documented many of these issues with multiple videos. Despite providing evidence and repeatedly reporting these problems, BMW has ignored my concerns and has not adequately resolved the defects.
I was driving on the interstate at about 65-70 MPH when the sunroof exploded without apparent cause. This caused glass to be scattered throughout the vehicle and given the sudden event, sound and disruption to driving I would say that this is a safety issue. The same day this happened I dropped the car off at the dealer for repair estimate and coincidentally there was another BMW, a new X7, that just had the same thing happen without cause. This makes me think that there is a manufacturing defect.
The contact owns a 2024 BMW X3. The contact stated while driving 5 MPH, attempting to park the vehicle in the park the vehicle, while depressing the brake pedal the vehicle unintendedly accelerated independently causing the vehicle to drove over the curb and the contact mention due to the impact the rear passenger tire was damaged and before the brake pedal she could hear the vehicle began to decelerate independently and while depressing the brake pedal with her left foot . No warnings light illuminated A dealer was contacted. The vehicle was towed to the dealer where they inspected the vehicle, and they informed the consumer there was no failure. The contact mention that this failure had occurred on two different occasions. The manufacturer was notified of the failure offered no assistance and denied helping the consumer. The approximate failure mileage was 17,903.
The contact owns a 2024 BMW X3. The contact stated that while driving at an undisclosed speed, the windshield unexpectedly cracked on several occasions without impact. The contact stated that the crack originated at the top of the windshield and extended approximately six inches toward the driver’s side. The vehicle was taken to the dealer, but was not inspected. The dealer ordered replacement windshields several times. The contact stated that after the windshield was replaced, the failure recurred. The manufacturer was made aware of the failure. The approximate failure mileage was 45,000.
To Whom It May Concern, I am submitting this supplemental update to formally document continued delay and lack of action by BMW following notification of serious vehicle safety concerns involving risk to minor passengers. BMW was notified in writing of multiple safety-related incidents involving system reliability and unauthorized access behavior. These concerns escalated to an incident occurring while the vehicle was in motion, presenting immediate risk to occupants, including two minor children. Despite acknowledgment of these concerns, BMW has: Failed to open a repair order to document the safety defects; Conditioned inspection on continued operation of a vehicle reported as unsafe; Failed to provide a timely, safe alternative path for inspection (e.g., coordinated tow and uninterrupted transportation); Gone silent for extended periods after acknowledgment of safety risk. I have expressly stated that the vehicle is unsafe to operate and that continued delay creates ongoing risk. I have also stated my willingness to cooperate fully with inspection and documentation provided that such cooperation does not require placing occupants at risk. This supplemental notice is submitted to preserve the record that continued inaction following acknowledgment of a safety concern may constitute failure to mitigate known risk. All communications, incidents, and delays are being documented. I respectfully request that this update be added to the record and considered as part of any safety or compliance review. Sincerely, [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
This submission is a supplemental update to my existing NHTSA complaint regarding my BMW X3. On [XXX], at approximately [XXX], while the vehicle was traveling approximately 40 MPH with the doors locked, the rear passenger door opened while the vehicle was in motion. A [XXX] child was secured in a rear car seat at the time. A [XXX] child witnessed the event while I was dropping him off at school. No audible or visual warning alerts activated before or during the incident. This event follows prior electronic access and system reliability concerns reported in November and December 2025, including operation without key presence and unauthorized access behavior. I believe these events may be related and indicative of a broader electronic or body control system failure. Due to the seriousness of this incident involving minor occupants, I no longer consider the vehicle safe to operate. The vehicle is pending inspection and has not been driven further. I am submitting this update to document a potential child-safety defect and to ensure this information is considered as part of NHTSA’s review. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
I am submitting a supplemental update to my existing safety complaint regarding my BMW vehicle. On December 29, 2025, additional safety-related malfunctions occurred while the vehicle was parked and without the key present. A vehicle window rolled down autonomously, and the heating system temporarily stopped functioning during winter conditions. These failures follow an earlier incident on November 15, 2025, in which the vehicle continued operating without the key present and without any audible or visual warning, while two minor children were occupants. The involvement of multiple electronic systems—including key detection, window controls, and HVAC—suggests a potential electronic network or CAN-bus-related defect. These conditions present risks related to vehicle security, environmental exposure, and passenger safety. The vehicle is currently unsafe for transport of minors and unreliable for use during winter conditions. I am submitting this update so NHTSA’s records reflect continued post-notice safety malfunctions.
Supplemental Update – Manufacturer Response to Safety Complaint (BMW) I am submitting this supplemental update in connection with my existing NHTSA safety complaint regarding my BMW vehicle. Following my report that the vehicle continued operating without the key present while transporting minor children, BMW of North America acknowledged the concern and indicated it was under review. However, BMW has now stated that it is closing my case file without: • Conducting any inspection; • Issuing written findings; • Providing a safety explanation or analysis; or • Confirming whether the reported behavior is a defect, system failure, or normal operation. BMW has conditioned further assistance on dealership inspection while simultaneously closing the manufacturer-level case, creating a gap in accountability and preventing meaningful review of the safety issue at the corporate level. I am not refusing inspection and remain willing to present the vehicle. My concern is that BMW’s attempt to close the case prior to evaluation undermines safety reporting and limits transparency regarding potential risks to drivers and passengers. Please add this update to my complaint record for consideration in any review or investigation.
Filed by owners of this model year and unverified by NHTSA — one person’s account, not an established fact.