2021 BMW X1
Check a specific vehicle
This page describes the model. To see how one particular car is equipped, and whether its identifier is valid, decode its VIN.
Decode a VINThis page describes the model. To see how one particular car is equipped, and whether its identifier is valid, decode its VIN.
Decode a VIN1 recall and 8 owner complaints on record for this model year.
Almost all of this describes the model year, not the individual car. Nothing here can tell you about this vehicle’s mileage, accidents or ownership — no identifier encodes those.
I was involved in an accident today and the front steering wheel airbags didn’t deploy The blue car in the pictures turned in front of me and I hit them
The contact owns a 2021 BMW X1. The contact stated that while driving at approximately 65 mph, another vehicle crashed into the front passenger side of the vehicle. The contact mentioned the air bags failed to deploy from the intensity of the vehicle. A police report was filed. The contact stated that the driver sustained a broken right hand that needed medical attention and was unaware of the other vehicle injuries. The vehicle was towed to the body shop. The dealer was not contacted. The contact attempted to contact the manufacturer but there was no answer. The approximate failure mileage was 6,000. The VIN was not available.
I got into an accident, i was hit on the driver side and the car was pushed to hit a tree, the air bag did not deploy.
The contact owns a 2021 BMW X1. The contact stated that while driving at an undisclosed speed, the vehicle stalled. The contact stated that the navigation screen was glitching and became inoperable. The service message was displayed. There was a red triangle with an exclamation mark displayed. The vehicle was difficult to start. The contact stated that the failure was caused by a failure with the grounding cable. The vehicle was taken to the local dealer, where it was diagnosed and determined that the grounding cable was underneath the vehicle. The battery was previously replaced. No additional repairs were completed. The manufacturer was contacted and referred the contact to the dealer for assistance. The manufacturer confirmed that there was no warranty coverage on the vehicle associated with the repair. The failure mileage was approximately 35,000.
At approximately 20,000 miles, the vehicle was inspected by an authorized dealer due to abnormal noises from the front suspension when turning the steering wheel. The dealer confirmed abnormal noise from the front struts when the wheels were turned while the vehicle was on a lift and diagnosed premature front strut failure. The affected components are available for inspection upon request. Repair was quoted but not performed. This condition involves a safety-critical suspension component and may affect vehicle handling, stability, and braking performance, particularly during turning or emergency maneuvers. This issue follows a prior safety-related brake failure at approximately 17,000 miles. At that time, a brake system warning light illuminated, and the condition was confirmed and repaired by the dealer. Both incidents involve safety-critical systems occurring at unusually low mileage. No warning lights or messages were observed prior to the suspension issue. The vehicle has not been involved in a collision and has not been inspected by police or insurance representatives.
While I was driving my BMW X1 1 to 3 weeks ago, frontal collision warning malfunction, pedestrian alert and request service flashed. It was a distraction and not safe. When My husband brought it to the dealership, they were not certain how to fix it. They took a video while doing diagnostic. The right bumper is pop out a little bit because it got hooked to a protruding rod in a concrete parking block while I was parking in front of a food store in Raritan sometime last year. I did not have it fix yet because it was not so obvious and the aesthetics of the car was not much affected. For that reason, the man in the video was saying that he saw a little damage there and was assuming that there’s sort of impact there to the right but it’s hard for him to tell. He was talking of a hard impact which did not happen. He said, visually he could not see anything that is bent but usually if there is a hard impact, it usually twigs the knuckle or the tire rod and he was pointing to those. He also said that when there is a hard impact, they usually recommend to replace the steering rack which is very delicate electronic steering rack and he was pointing where it is. He said, those 3 parts need to be replaced and he will do an alignment once they’re done. He said the reason why always the collision warning are coming on are because of all the steering angle faults from the steering moving so far off. I spoke with the manager last Monday and agreed with alignment but he said if the warning won’t go away after then, I have to spend about $5,000 to replace all those 3 parts. They were not listening that the car did not get a hard impact that’s why they could not see anything bent. It was just the right side of the bumper that was hooked to a rod. They did not even talk about checking the cameras or sensor of the car which according to google is the common cause of frontal collision malfunction. The root cause should be found to fix the problem.
The car was displaying these messages: Frontal Collision Warning System: Malfunction, Brake intervention not available. Visual and acoustic ️ warnings active. Consult service center. Daytime Pedestrian Warning reduced:Brake intervention not possible, but visual and acoustic warnings are still given. Consult service center. It was inspected by the dealership but they were saying that I have to pay $5,000 for it to be fixed which is not right because I think it is a manufacturer’s defect. They were blaming it to a collision which never happened. A portion of the right side of the bumper came off sometime last year because as I was trying to park it, it got hooked to a rod in a parking block. It is not even obvious that’s why I did not have if fix yet, not a priority for my budget. I need a car to go to work. An unfix controller area network and electronic control units could lead to fatal accident.
On November 18, 2022, around 9:45 a.m. on Rt. 462 in South Carolina. I was driving my 2021 BMW X1 when “boom.” I thought I’d been shot at with a shotgun. I nearly lost control of the car. As it turns out, by sunroof exploded. (See attached photo). My BMW dealer is covering it under warranty, but I thought I should let NHTSA know. It has been replaced, so inspection is not an option. There were no symptoms prior to the failure.
Filed by owners of this model year and unverified by NHTSA — one person’s account, not an established fact.
BMW of North America, LLC (BMW) is recalling certain 2021 2 Series (230i, 230i xDrive, M240i, M240i xDrive), 330e, 330e Xdrive, 4 Series Coupe (430i, 430i xDrive, M440i xDrive) M4 Coupe, M4 Competition Coupe, BMW 4 Series Convertible (430i, M440i), BMW X1 sDrive28i, xDrive28i, 2 Series Gran Coupe (228i, 228i xDrive, M235i xDrive), M2 Competition Coupe, 330i, 330i xDrive, M340i, M340i xDrive, M3, M3 Competition, 530i, 530i xDrive, 540i, 540i xDrive, MINI Hardtop 2 Door (Cooper, CooperS, JCW), X2 sDrive28i, X2 xDrive28i, X2 M35i, Z4 sDrive30i, Z4 M40i, MINI Hardtop 2 Door (Cooper SE), MINI Convertible (Cooper, Cooper S, JCW), MINI Clubman (Cooper S, Cooper S All4, JCW), MINI Countryman (Cooper, Cooper All4, Cooper S, Cooper S All4, JCW All4), Rolls Royce Ghost, MINI Countryman (Cooper S E All4), Rolls Royce Phantom, Rolls Royce Cullinan, and Toyota Supra vehicles. The passenger seat belt Automatic Locking Retractor (ALR) may deactivate early, before the webbing fully retracts. As such, these assemblies fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 208, "Occupant Crash Protection."
Remedy: Dealers will inspect the seat belt retractors (including the seat belts) and, if necessary, replace the retractors, free of charge. Owner notification letters were mailed on September 3, 2021. Owners may contact BMW customer service at 1-800-525-7417; 1-866-825-1525 (MINI); 1-877-877-3735 (Rolls Royce); and 1-888-270-9371 (Toyota).
Published by model year, not by VIN — may not apply to this vehicle, or may already have been done. Confirm with a dealer.
The seatbelts in the second row may not have been manufactured correctly and could cause the car-sensitivity sensors to fail. This could reduce the protective effect of the seatbelts and lead to injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The seat belts of the car were not manufactured correctly. In the event of a collision or accident, the restraint function of the seat belts may be reduced and may not provide the necessary protection. As a result, there may be an increased risk of injury. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The cell modules in the vehicles concerned were not produced in accordance with the specifications, which may cause the module frame to fail. This may lead to a shutdown of the high-voltage system and fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The material used for the B-pillar reinforcement plates is inadequate. This can alter the crash characteristics, leading to an increased risk of injuries in the event of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the inflator of the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments of the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The driver airbag inflator may malfunction due to long-term degradation. In this case, if the airbag is deployed in an accident, the internal pressure in the inflator may be too high. The inflator could burst. Metal fragments may cause injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The hollow shaft of the servomotor was not welded correctly. The weld may not be able to withstand high braking pressure build-up and may break. In this case, the reduced braking performance requires greater force and the braking distance may increase. In addition, the ABS and DSC brake control systems are not assisted. This increases the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant within the integrated inflator of driver airbags can deteriorate during time. If the airbag deploys, it could result in fragments from the inflator casing injuring the vehicle’s occupants. The product does not comply with the Regulation on the approval and market surveillance of Motor Vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The front left seat's height adjustment mechanism may have been incorrectly riveted, potentially compromising the seat's structural integrity. In an accident, this could have a negative impact on the restraint system and increase the risk of injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The seat recliner adjuster may not be correctly welded, which could cause the backrest not to lock. If it doesn't lock, the seatback might not stay secure in a collision, increasing the risk of injury. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The integrated braking system could be compromised, which could lead to an unexpected failure of the hydraulic braking assistance, thereby requiring greater pressure on the brake pedal. This can result in a longer braking distance, as well as failure of the Anti-lock Braking System (ABS) and the Dynamic Stability Control (DSC), increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Matched on brand and model name — Safety Gate publishes no VIN. Check the production dates, and quote the recall code to a dealer.