3 Rückrufe und 114 Halterbeschwerden für dieses Modelljahr erfasst.
Diese Seite beschreibt das Modell. Um zu sehen, wie ein einzelnes Fahrzeug ausgestattet ist und ob seine Kennung gültig ist, entschlüsseln Sie die FIN.
FIN entschlüsselnFast alles hiervon beschreibt das Modelljahr, nicht das einzelne Fahrzeug. Nichts davon sagt etwas über Laufleistung, Unfälle oder Eigentum dieses Autos — keine Kennung kodiert das.
THIS MORNING 03/13/2020 AT APROX. 2:30AM MY BMW X5 2003 WAS ENGULFED IN FLAMES FOR NO REASON AND MY TWO GERMAN SHEPHERDS HEY YOU AND MY BABY DIESEL WERE INSIDE,AND HOW ONE MADE IT OUT AND THE BABY DIDNT, I BUSTED WINDOWS CAUSE I HEARD HIM CRYING ,,,,I COULDNT GET HIM I TRIED TO I TRIED OH MY GOD MY POOR BABY , I WAS INJURED AND SCARED FOR LIFE WITH THAT. MY CAR WAS OFF AND PARKED IN FRONT OF A FRIENDS HOUSE ON A SIDE STREET, ALL A LOSS. NO PICTURES TAKEN ,SEVERAL POLICE AND FIRE DEPT. CAME.
TL-THE CONTACT OWNS A 2003 BMW X5. THE CONTACT STATED WHILE DRIVING AT AN UNKNOWN SPEED ATTEMPTING TO ENGAGED THE BRAKES, THE VEHICLE BEGAN TO ACCELERATE AT FULL SPEED. THE VEHICLE CRASHED INTO A TREE. THE VEHICLE WAS DEEMED DESTROYED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 140,000. PAM
THE SEAT HEATER WAS TURNED ON TO THE HIGHEST SETTING. WHILE DRIVING WITH MY 4-YEAR OLD SON IN THE BACK, I SMELLED SMOKE, THEN SHORTLY AFTER, MY LEFT BUTT CHEEK FELT BURNING. I LOOKED DOWN AND SURE ENOUGH SMOKE WAS COMING OUT OF A AN AMBER GLOWING HOLE IN THE LEATHER SEAT. LUCKILY I DIDN'T PANIC... SLOWED DOWN AND PULLED OVER AND TURNED OFF THE HEATER. I DON'T USE THE HEATER ANYMORE BECAUSE EVEN AT THE LOWEST SETTING IT STARTS SMOKING AGAIN. *TR
TL*THE CONTACT OWNS A 2003 BMW 540. WHILE THE CONTACT'S DAUGHTER WAS DRIVING APPROXIMATELY 30 MPH, SHE HEARD A LOUD NOISE. THE FRONT DRIVER'S SIDE DOOR AIR BAG AND REAR DOOR AIR BAGS DEPLOYED, INJURING HER LEFT ARM AND LEG. THE VEHICLE WAS DRIVEN TO A BMW DEALER. THE VIN WAS UNKNOWN. THE CURRENT AND FAILURE MILEAGES WERE 68,000.
Wiring dash fire. Heavy smoke from dash and vehicle completely in flame in minute. My son sent me a recording while it was happening, he did no know what to do or what was happening.
The contact owns a 2003 BMW X5. The contact stated the vehicle was parked, while entering the vehicle he noticed the dashboard was melted, which was caused by a fire that occurred independently. The contact stated he reviewed a camera that was near the location of the vehicle and saw the fire occur on the video. The contact did not call the fire department to report the incident. The contact stated no one was injured nor sought medical attention. The vehicle was not drivable. The contact towed the vehicle to the local dealer. The vehicle was not diagnosed or repaired. The manufacturer had been informed of the failure. The failure mileage was approximately 137,000.
My 2003 BMW X5 was parked outside of my house, turned off and not driven for hours and burst into flames consuming the whole dashboard, fire department said that fire was due to some electrical problem with car, very scary please help could of killed my family the incident was recorded on home surveillance footage, but I cannot upload because of size
LH - Driver side seat caught fire and melted through seat material and melted onto my coat. there are burn marks / holes through the seat due to the heater malfunction/ short. My coat was also ruined with plastic melted onto it from the seat.
TL* THE CONTACT OWNS A 2003 BMW X5. WHILE ATTEMPTING TO DRIVE THE VEHICLE, THE CONTACT NOTICED SMOKE UNDER THE HOOD. WHEN HE OPENED THE HOOD, HE NOTICED FLAMES AROUND THE MOTOR. THE CONTACT QUICKLY EXTINGUISHED THE FIRE. THERE WERE NO WARNING INDICATORS ILLUMINATED. THE CONTACT CALLED BMW OF DALLAS (6200 LEMMON AVE, DALLAS, TX 75209, (972) 763-5528) AND WAS INFORMED THAT THE VEHICLE WAS OUT OF WARRANTY. THE VEHICLE WAS NOT TAKEN TO A DEALER AND WAS NOT REPAIRED. THE MANUFACTURER WAS NOT MADE AWARE OF THE FAILURE. THE FAILURE MILEAGE WAS APPROXIMATELY 180,000.
PARKED VEHICLE, NOTICE SMOKE COMING FROM UNDERNEATH HOOD, TURNED INTO FIRE, HEARD 'BOOM,' VEHICLE EXPLODED, HOUSTON FIRE DEPT RESPONDED AND WILL HAVE REPORT OF THIS INCIDENT
DRIVING SLOWLY DOWN STREET, SAW SMOKE COMING FROM FRONT RIGHT UNDER HOOD, PULED OVER TO SIDE, FLAMES VISIBLE COMING FROM HOOD, WITHIN 15 MINUTES, ENTIRE FRONT ON FIRE, FIRE DEPARTMENT CAME WITHIN 5-10 MINUTES, MAJOR FIRE, TOTAL LOSS. ALL THIS TOOK ABOUT 30 MINUTES. FORTUNATELY, NO INJURIES.
TL* THE CONTACT OWNS A 2003 BMW X5. WHILE DRIVING APPROXIMATELY 65 MPH, THERE WAS THE SMELL OF PLASTIC BURNING AND THE VEHICLE WOULD NOT ACCELERATE. THE CONTACT STATED THAT THERE WAS SMOKE COMING FROM THE FRONT OF THE VEHICLE. THE ENGINE STALLED WITHOUT WARNING. MOMENTS LATER, THE VEHICLE WAS ENGULFED IN FLAMES. THE FIRE DEPARTMENT EXTINGUISHED THE FIRE AND FILED A REPORT. THE VEHICLE WAS BURNED DOWN TO THE FRAME. THE VEHICLE WAS DESTROYED AND TOWED TO A BODY SHOP. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 100,000.
TL* THE CONTACT OWNS A 2003 BMW X5. THE CONTACT STATED THAT THERE WAS A ABNORMAL BURNING ODOR. THE CONTACT THEN NOTICED THAT THE DRIVER'S SIDE SEAT HEATER HAD MALFUNCTIONED AND BURNED A HOLE THROUGH THE LEATHER. THE VEHICLE WAS NOT TAKEN TO A DEALER FOR DIAGNOSTIC TESTING. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE. THE VEHICLE WAS NOT REPAIRED. THE APPROXIMATE FAILURE AND CURRENT MILEAGE WAS 90,000.
TL* THE CONTACT OWNS A 2003 BMW X5. THE CONTACT STATED THAT THE FRONT PASSENGER SIDE CAUGHT FIRE WHILE PARKED IN A RESIDENTIAL GARAGE. THE MANUFACTURER INVESTIGATED THE FAILURE AND CONCLUDED THAT CAUSE OF THE FIRE WAS NOT DUE A MANUFACTURING DEFECT. A POLICE REPORT WAS FILED OF THE INCIDENT. THE CONTACT STATED THAT THE BATTERY WAS REPLACED TWICE AND THE COMPUTER SYSTEM WAS REPLACED THREE TIMES PRIOR TO THE FIRE. THE VEHICLE WAS DESTROYED. THE APPROXIMATE FAILURE AND CURRENT MILEAGE WAS 150,000. UPDATED 2/15/13 *CN THE CONSUMER BELIEVED THE FIRE WAS DUE TO AN ELECTRICAL FAILURE. UPDATED 02/02/513
MY 2003 BMW 530I SEDAN CAUGHT FIRE DUE TO AN ELECTRICAL FAULT WHILE PARKED IN NEW HAVEN, CONNECTICUT. THE FIRE DEPARTMENT AND POLICE WERE CALLED. CASE #[XXX] WAS ASSIGNED BY OFFICER [XXX] OF THE NEW HAVEN PD. THE CAR, TOO BADLY DAMAGED TO REPAIR, WAS HAULED AWAY FOR EVENTUAL SCRAPPING. I WAS CLOSE TO THE CAR WHEN THE FIRE STARTED. FLAMES WERE ERUPTING FROM THE DASH, WHERE THE CLIMATE CONTROL SWITCHES ARE LOCATED. I TRIED SMOTHERING THE FLAMES WITH A SWEATER. THIS DID NOT INTERRUPT THE PROGRESS OF THE FIRE. THERE WAS NO PERSONAL INJURY OR PROPERTY DAMAGE OTHER THAN TO THE CAR AND ITS CONTENTS. ITEMS SITUATED IN THE FRONT SEAT AREA WERE NOT RECOVERED, DUE TO THE INTENSITY OF THE FIRE. THE APPARENT CAUSE OF THE FIRE WAS AN ELECTRICAL FAULT. IN 2010 NEW COUNTRY BMW IN HARTFORD TWICE REPLACED THE CLIMATE CONTROL FAN FINAL STAGE RESISTOR, ONCE IN APRIL AND AGAIN IN OCTOBER, AT NO CHARGE FOR THE SECOND REPLACEMENT. IN THE DAYS BEFORE THE FIRE THE CLIMATE CONTROL WAS AGAIN ACTING ERRATICALLY, AND THE EVIDENCE INDICATES THE FINAL STAGE RESISTOR WAS FAILING ONCE AGAIN. BMW NORTH AMERICA INSPECTED THE CAR AND CONFIRMED THAT THE FIRE WAS CAUSED BY AN ELECTRICAL FAULT IN THE AREA BEHIND THE DASH WHERE THE FINAL STAGE RESISTOR IS LOCATED. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).*TR
Von Haltern dieses Modelljahrs eingereicht und von der NHTSA nicht geprüft — die Schilderung einer Person, keine feststehende Tatsache.
2 Rückrufe enthalten eine Fahrverbots- oder Abstellwarnung. Prüfen Sie, ob dieses Fahrzeug bereits instand gesetzt wurde, bevor Sie es fahren oder abstellen.
BMW of North America, LLC (BMW) is recalling certain 2000-2002 BMW 320i, 323i, 325i, 325xi, 330i, 330xi, 323Ci, 325Ci, 330Ci, M3, 323iT, 325iT and 325xiT vehicles, 2001-2002 525i, 530i, 540i, M5, 525iT and 540iT vehicles, and 2001-2003 X5 3.0i, X5 4.4i, and X5 4.6is vehicles. These vehicles may have had a driver-side air bag module installed as replacement equipment such as after a vehicle crash necessitating replacement of the original air bag, or as a remedy part for a prior recall. These replacement modules contain an air bag inflator that may rupture due to propellant degradation occurring after long-term exposure to lower absolute humidity, temperature and temperature cycling.
Abhilfe: Owners are advised not to drive their vehicles until the vehicle has been remedied. BMW will notify owners, and dealers will inspect the driver side air bag module, replacing it as necessary, free of charge. The recall began March 15, 2017. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain model year 2002-2005 325i, 325xi, 330i, and 330xi Sedans, and 325xi and 325i Sportswagons, 2002-2006 330Ci, 325Ci, and M3 Convertibles and 325i, 330i, and M3 Coupes, 2002-2003 M5, 540i, 525i Sedan, and 530i Sedans, and 540i and 525i Sportswagons, and 2003 X5 3.0i and 4.4i Sports Activity Vehicles. Please note that the 5-series and X5 vehicles are only included if they are equipped with the optional sports steering wheel. The affected vehicles are equipped with a dual-stage driver frontal air bag that may be susceptible to moisture intrusion which, over time, could cause the inflator to rupture.
Abhilfe: Owners are advised not to drive their vehicles until the vehicle has been remedied. BMW will notify owners, and dealers will replace the front driver air bag module, free of charge. The recall began Aug 2016. Owners may contact BMW customer service at 1-800-525-7417. Note: This recall supersedes recall 14V-348 in its entirety. Additionally, vehicles that have had their driver side frontal air bag replaced previously as part of a recall remedy need to have their air bag replaced under this recall as well. Note: On December 17, 2015 BMW removed the model year 2004 X5 3.0i and 4.4i Sports Activity vehicle from this recall. Those vehicles were mistakenly identified as including the air bags that are subject to this recall.
ON CERTAIN PASSENGER VEHICLES, IT IS POSSIBLE THAT THE DISTANCE BETWEEN THE BRAKE LINE AND THE STEERING SHAFT JOINT IS NOT SUFFICIENT. IF THIS OCCURS, THE BRAKE LINE COULD COME INTO CONTACT WITH THE JOINT AND EVENTUALLY SUFFER DAMAGE AND CORROSION.
Abhilfe: DEALERS WILL INSPECT THE DISTANCE BETWEEN THE BRAKE LINE AND THE STEERING SHAFT JOINT, AND IF NECESSARY, INCREASE THE DISTANCE. OWNER NOTIFICATION BEGAN JUNE 23, 2003. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT BMW AT 1-800-831-1117.
Nach Modelljahr veröffentlicht, nicht nach FIN — betrifft dieses Fahrzeug möglicherweise nicht oder wurde bereits erledigt. Beim Händler bestätigen.
Water may come into contact with the starter relay and gradually cause corrosion. This could affect the electrical connection inside the relay and make the engine difficult to start. It may also result in a short circuit and could cause the starter to overheat leading to a fire when the vehicle is in motion or when it is parked with the ignition off. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The engine starter’s electrical contacts may overheat and cause the vehicle to start improperly. Continued starting attempts can intensify the overheating and ignite surrounding components, potentially leading to a vehicle fire while driving or shortly after parking. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The RSW22 starter with reinforced water tightness (RWT) may experience increased abrasion of the magnetic contact, causing deposits to build up at the lowest point inside the relay. These deposits may increase relay contact resistance, leading to starting failures or short circuits. If a short circuit occurs, either when attempting to start the vehicle or while driving due to vibration-related movement of the deposits, it could cause a thermal event and increase the risk of fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The positive battery cable of the starter-generator may not have been manufactured correctly. This could result in a loose electrical connection, leading to excessive contact resistance. The vehicle cannot charge or start. Contact points in the starter-generator could overheat and cause a vehicle fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The chemical substances in the inflators of the TAKATA PSDI4 airbags may deteriorate over time, particularly in warm, humid climates. This could cause the airbag to rupture with too much force in the event of an accident, which could lead to serious or even fatal injuries in the worst-case scenario. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The failure concerns the RSW22 starter, type RWT (reinforced for watertightness). Increased abrasion of the magnetic contact can lead to the formation of deposits at the lowest point of the relay interior. This in turn can increase the resistance of the relay contact, causing accidental ignition or even short circuits, possibly leading to a thermal reaction and fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The failure concerns the RSW22 starter, type RWT (reinforced for watertightness). Increased abrasion of the magnetic contact can lead to the formation of deposits at the lowest point of the relay interior. This in turn can increase the resistance of the relay contact, causing accidental ignition or even short circuits, possibly leading to a thermal reaction and fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The hollow shaft of the servomotor was not welded correctly. The weld may not be able to withstand high braking pressure build-up and may break. In this case, the reduced braking performance requires greater force and the braking distance may increase. In addition, the ABS and DSC brake control systems are not assisted. This increases the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The software-based overload protection function cannot sufficiently prevent the starter being overloaded in the event of repeated long start-up attempts. The starter may overheat or sparks may be produced as a result of an increased current flow. This increases the risk of a fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The gas generator in knee airbag modules was not properly inserted into the air cushion, resulting in the cushion failing to unfold sufficiently. As a result, it may not be able to deploy correctly in the event of an accident, leading to a reduction in the restraint effect, increasing the risk of injury to the occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
A seam on the inflator housing of the driver airbag may not have been correctly welded. In case of accident, when the airbag is deployed, the inflator can burst, releasing metal parts which could cause injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The stated maximum load specified in the user manual is incorrect. This could cause users to overload the vehicle, potentially leading to damage to the car and an increased risk of accidents and injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The integrated braking system could be compromised, which could lead to an unexpected failure of the hydraulic braking assistance, thereby requiring greater pressure on the brake pedal. This can result in a longer braking distance, as well as failure of the Anti-lock Braking System (ABS) and the Dynamic Stability Control (DSC), increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The dashboard in the affected vehicles may not have been manufactured to the manufacturer specifications. In the event of anaccident, the passenger side airbag may not deploy as intended which could increase the risk of injury to the frontpassenger. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Due to a manufacturing error, the weld seam of the integrated transmission control unit (ITCU) may not have been correctly executed. As a result, transmission oil could leak into the ITCU, causing it to fail. This may lead to transmission seizure, increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Abgeglichen über Marke und Modellname — Safety Gate veröffentlicht keine FIN. Prüfen Sie die Produktionsdaten und nennen Sie dem Händler den Rückrufcode.