2008 BMW X6
8 recalls and 4 owner complaints on record for this model year.
Check a specific vehicle
This page describes the model. To see how one particular car is equipped, and whether its identifier is valid, decode its VIN.
Decode a VIN8 recalls and 4 owner complaints on record for this model year.
This page describes the model. To see how one particular car is equipped, and whether its identifier is valid, decode its VIN.
Decode a VINAlmost all of this describes the model year, not the individual car. Nothing here can tell you about this vehicle’s mileage, accidents or ownership — no identifier encodes those.
4 recalls carry a do-not-drive or park-outside warning. Check whether this vehicle was remedied before driving or storing it.
BMW of North America, LLC (BMW) is recalling certain 2008-2013 128i and 135i Convertibles, 128i, 135i, and M Coupes, 2007-2010 X3 30si and X3 xDrive30i, 2013-2015 X1 sDrive28i, X1 xDrive28i and X1 xDrive35i, 2007-2013 328i, 328i xDrive, 335i, 335is, 335i xDrive and M3 Coupes, 2006-2011 328i, 328xi, 328i xDrive, 325i, 325xi, 330i, 330xi, 335i, 335xi, 335i xDrive and M3, 2009-2011 335D, 2006-2012 325xi, 328i, 328xi and 328i xDrive, 2010-2011 X6 ActiveHybrid, 2007-2013 328i, 335i, 335is, M3 Coupes, X5 30si, X5 xDrive30i, X5 xDrive35i, X5 48i, X5 xDrive48i, X5 xDrive50i and X5 M, 2009-2013 X5 xDrive35d and 2008-2014 X6 xDrive35i, X6 xDrive50i and X6M vehicles equipped with non-desiccated driver frontal air bag inflators containing phase stabilized ammonium nitrate (PSAN) that were used as interim remedy parts for previous Takata recalls. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Remedy: BMW will notify owners, and dealers will replace the driver air bag. On X5 and X6 vehicles, only the inflator will be replaced. All repairs will be performed free of charge. The recall began March 11, 2020. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2009-2012 X5 xDrive35d, 2008-2012 X6 xDrive35i, X6 xDrive50i and X6 M, 2007-2012 X5 30si, X5 xDrive30i, X5 xDrive35i, X5 48i, X5 xDrive48i, X5 xDrive50i and X5 M and 2010-2011 X6 ActiveHybrid vehicles equipped with non-desiccated, passenger frontal air bag inflators containing phase stabilized ammonium nitrate (PSPI-2) propellant that were used as interim remedy parts for previous Takata recalls. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Remedy: Owners are advised not to drive their vehicles until this remedy is performed. BMW will notify owners, and dealers will replace the passenger front air bag, free of charge. The recall began March 11, 2020. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2007-2013 X5 xDrive30i, X5 xDrive35i, X5 xDrive48i, X5 xDrive50i and X5 M vehicles, 2008-2014 X6 xDrive35i, X6 xDrive50i and X6 M vehicles, 2009-2013 X5 xDrive35d vehicles and 2010-2011 X6 ActiveHybrid vehicles. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Remedy: Owners are advised not to drive their vehicles until the remedy is performed. BMW will notify owners, and dealers will replace the passenger frontal air bag module, free of charge. The recall began March 14, 2019. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2011-2012 BMW 550i, 550i xDrive, 550i Gran Turismo, 550i Gran Turismo xDrive, 750i, 750Li, 750i xDrive, 750Li xDrive, 760Li, X5 xDrive50i, X5 M, X6 xDrive50i, X6 M, ActiveHybrid7, MINI Cooper S Convertible, John Cooper Works (JCW) Convertible, Cooper S Countryman, Cooper S Countryman ALL4, Cooper S, JCW, Cooper S Clubman, JCW Clubman, Cooper S Roadster, JCW Roadster, Cooper S Coupe, JCW Coupe and Rolls-Royce Ghost, 2011 BMW X6 Hybrid and 2012 BMW 650i Coupe, 650i xDrive Coupe, 650i Convertible and 650i xDrive Convertible vehicles. The electric auxiliary water pump may fail and cause the circuit board to overheat.
Remedy: BMW will notify owners, and dealers will replace the electric auxiliary water pump, free of charge. Depending on the model, there are currently limited parts available, however not all parts are available at this time. Owners will be notified of the recall beginning June 11, 2018, and will receive a second notification when remedy parts become available. Owners may contact BMW customer service at BMW 1-800-525-7417, MINI at 1-866-825-1525, or Rolls-Royce at 1-877-877-3735. Note: BMW recommends that owners park their vehicle outdoors until the recall remedy has been performed.
BMW of North America, LLC (BMW) is recalling certain 2012 X5 xDrive30i, X5 xDrive35i, X5 xDrive48i, X5 xDrive50i, X5 M, X6 xDrive35i, X6 xDrive50i, and X6 M vehicles originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, BMW is recalling certain 2009 X5 xDrive30i, X5 xDrive35i, X5 xDrive48i, X5 xDrive50i, and X5 M vehicles, 2008-2009 X6 xDrive 35i, X6 xDrive50i, X6 M, and 2009 X5 xDrive35d vehicles originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Additionally, unless included in "Zone A" or "Zone B" above, BMW is recalling certain 2007-2008 X5 xDrive30i, X5 xDrive35i, X5 xDrive48i, X5 xDrive50i and X5 M vehicles, and 2008 X6 xDrive35i, X6 xDrive50i, and X6 M vehicles originally sold, or ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to high absolute humidity and temperature cycling.
Remedy: Owners are advised not to drive their vehicles until the remedy is performed. BMW will notify owners, and dealers will replace the front passenger air bag inflator or air bag module, free of charge. Interim letters were mailed March 2017. Owners will receive a second notice when remedy parts become available. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain model year 2007-2011 BMW X5 3.0si, X5 4.8i, X5 M, X5 xDrive30i, X5 xDrive35i, X5 xDrive48i and X5 xDrive50i, 2008-2011 X6 x Drive35i, X6 xDrive50i and X6 M, 2010-2011 X6 ActiveHybrid, 535i xDrive Gran Turismo, 535i Gran Turismo, 550i xDrive Gran Turismo and 550i Gran Turismo, 2011-2012 528i, 535i, 535i xDrive, 550i and 550i xDrive and 2012 535i ActiveHybrid, 640i Convertible, 650i Convertible, 650i xDrive Convertible, 650i Coupe and 650i Coupe xDrive vehicles. The affected vehicles have in-tank fuel pumps that may have insufficiently crimped wire contacts.
Remedy: BMW will notify owners, and dealers will replace the fuel pump module, free of charge. The recall began February 2017. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain model year 2007-2011 X5 xDrive30i, X5 xDrive35i, X5 xDrive48i, X5 xDrive50i and X5M vehicles, 2009-2011 X5 xDrive35d vehicles, 2008-2011 X6 xDrive35i, X6 xDrive50i and X6 M vehicles, and 2010-2011 X6 ActiveHybrid vehicles originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, BMW is recalling certain model year 2007-2008 X5 xDrive30i, X5 xDrive35i, X5 xDrive48i, X5 xDrive50i and X5M vehicles, and 2008 BMW X6 xDrive35i, X6 xDrive50i and X6 M vehicles originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Vehicles of these model years and models that were not originally sold or ever registered in either Zones A or B are not subject to this safety recall. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to high absolute humidity and temperature cycling.
Remedy: Owners are advised not to drive their vehicles until they have been repaired. BMW will notify owners, and dealers will replace the passenger frontal air bag inflator or air bag module, free of charge. The recall began July 28, 2017. Owners may contact BMW customer service at 1-800-525-7417.
BMW IS RECALLING CERTAIN MODEL YEAR 2011 5-SERIES, MODEL YEAR 2010-2011 5-SERIES GRAN TURISMO, MODEL YEAR 2009-2011 7-SERIES, MODEL YEAR 2010-2011 X5 SAV, AND MODEL YEAR 2008-2011 X6 SAV VEHICLES EQUIPPED WITH 8- OR 12-CYLINDER, TURBOCHARGED, ENGINES BECAUSE THE CIRCUIT BOARD FOR THE ELECTRIC AUXILIARY WATER PUMP CAN OVERHEAT.
Remedy: BMW WILL NOTIFY OWNERS, AND DEALERS WILL REPLACE THE AUXILIARY WATER PUMP FREE OF CHARGE. THE SAFETY RECALL BEGAN ON DECEMBER 19, 2011. OWNERS MAY CONTACT BMW CUSTOMER RELATIONS AND SERVICES AT 1-800-525-7417.
Published by model year, not by VIN — may not apply to this vehicle, or may already have been done. Confirm with a dealer.
Water may come into contact with the starter relay and gradually cause corrosion. This could affect the electrical connection inside the relay and make the engine difficult to start. It may also result in a short circuit and could cause the starter to overheat leading to a fire when the vehicle is in motion or when it is parked with the ignition off. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The engine starter’s electrical contacts may overheat and cause the vehicle to start improperly. Continued starting attempts can intensify the overheating and ignite surrounding components, potentially leading to a vehicle fire while driving or shortly after parking. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The RSW22 starter with reinforced water tightness (RWT) may experience increased abrasion of the magnetic contact, causing deposits to build up at the lowest point inside the relay. These deposits may increase relay contact resistance, leading to starting failures or short circuits. If a short circuit occurs, either when attempting to start the vehicle or while driving due to vibration-related movement of the deposits, it could cause a thermal event and increase the risk of fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The failure concerns the RSW22 starter, type RWT (reinforced for watertightness). Increased abrasion of the magnetic contact can lead to the formation of deposits at the lowest point of the relay interior. This in turn can increase the resistance of the relay contact, causing accidental ignition or even short circuits, possibly leading to a thermal reaction and fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The hollow shaft of the servomotor was not welded correctly. The weld may not be able to withstand high braking pressure build-up and may break. In this case, the reduced braking performance requires greater force and the braking distance may increase. In addition, the ABS and DSC brake control systems are not assisted. This increases the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The software-based overload protection function cannot sufficiently prevent the starter being overloaded in the event of repeated long start-up attempts. The starter may overheat or sparks may be produced as a result of an increased current flow. This increases the risk of a fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The gas generator in knee airbag modules was not properly inserted into the air cushion, resulting in the cushion failing to unfold sufficiently. As a result, it may not be able to deploy correctly in the event of an accident, leading to a reduction in the restraint effect, increasing the risk of injury to the occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The integrated braking system could be compromised, which could lead to an unexpected failure of the hydraulic braking assistance, thereby requiring greater pressure on the brake pedal. This can result in a longer braking distance, as well as failure of the Anti-lock Braking System (ABS) and the Dynamic Stability Control (DSC), increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The dashboard in the affected vehicles may not have been manufactured to the manufacturer specifications. In the event of anaccident, the passenger side airbag may not deploy as intended which could increase the risk of injury to the frontpassenger. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Due to a manufacturing error, the weld seam of the integrated transmission control unit (ITCU) may not have been correctly executed. As a result, transmission oil could leak into the ITCU, causing it to fail. This may lead to transmission seizure, increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Matched on brand and model name — Safety Gate publishes no VIN. Check the production dates, and quote the recall code to a dealer.
TL* THE CONTACT OWNS A 2008 BMW X6. THE CONTACT STATED THAT VEHICLE FAILED TO START AFTER MULTIPLE ATTEMPTS. THE CONTACT ALSO STATED THAT SEVERAL ELECTRIC FEATURES FAILED TO FUNCTION AS DESIGNED. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC AND DIAGNOSED WITH AN INTELLIGENT BATTERY SENSOR CABLE MALFUNCTION. THE CONTACT CALLED BMW OF HONOLULU (777 KAPIOLANI BLVD, HONOLULU, HI 96813) WHERE HE WAS INFORMED OF AN UNKNOWN MANUFACTURER'S RECALL THAT WAS INITIATED ON SIMILAR VEHICLES HOWEVER, THE VIN WAS NOT INCLUDED. THE CONTACT WAS REFERRED TO THE MANUFACTURER FOR ASSISTANCE. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE AND CONFIRMED THAT THE VIN WAS NOT INCLUDED. NO FURTHER ASSISTANCE WAS PROVIDED. THE VEHICLE WAS NOT REPAIRED. THE FAILURE MILEAGE 58,000.
DEFECTED AIR BACK HAS BEEN RECALLED SINCE MARCH. SO FAR, I DO NOT KNOW WHAT HAPPEN TO THE REPLACEMENT PART. CAN YOU PUT A LOT OF PRESSURE TO THE COMPANY FOR THIS PROBLEM. I HAVE BEEN DRIVING THIS SUV SINCE I RECEIVED THE RECALLED LETTER. EVERY TIME WE GET OUT WITH THIS SUV, WE PUT OUR LIFE ON THE LINE. HOW CAN WE DO TO GET IT REPLACE SOONER. PLEASE HELP.
I WAS TRYING TO PASS A CAR ON THE INTERSTATE WHEN THE POWER TO MY ENGINE WAS CUT BY THE CAR'S COMPUTER. THE CAR FOLLOWING ME ALMOST RAN INTO THE BACK OF ME. THIS HAPPENED THREE TIMES OVER 4 MONTHS. IN NUMEROUS WRITTEN LETTERS TO BMW AND TO THE DEALER, THEY RESPONDED BY SAYING IT WAS MY FAULT, BECAUSE I HAD NOT INSTALLED THE "PROPER" TIRES ON THE CAR WHEN THE ORIGINAL ONES WORE OUT. OR COURSE, THEY SOLD AND INSTALLED THE REPLACEMENTS, AND NEVER WARNED ME ABOUT ANYTHING. THE ORIGINAL 20" TIRES, AND THE ONLY "APPROVED" ONES, ARE RUN-FLAT HIGH PERFORMANCE TIRES THAT RIDE TERRIBLY, AND ARE NOT RECOMMENDED FOR WINTER DRIVING. SO I WANTED TO INSTALL ALL-SEASON TIRES - BMW DOESN'T APPROVE ANY ALL-SEASON TIRES FOR THIS CAR- NOT IN THE 20" SIZE REQUIRED. SO I PICKED A MODEL TIRE THAT MICHELIN SALES FOR SUMMER AND WINTER USE, AND THE DEALER OBTAINED THEM INSTALLED THEM - SAYING NOTHING ABOUT ANY PROBLEMS. TO MAKE A LONG STORY SHORT - THE BMW STABILITY CONTROL SYSTEM WAS PROGRAMMED FOR ONLY THIS ONE TIRE, AND NOW WITH DIFFERENT TIRES THE COMPUTER THINKS THE CAR IS SLIDING WHEN IT IS NOT, AND CUTS FUEL TO THE ENGINE. THIS HAPPENS IF I TRY TO PASS A CAR ON A CURVE. SO NOW I HAVE A CHOICE - I CAN DRIVE ON ALL SEASON TIRES THAT ARE REASONABLY EFFECTIVE IN THE SNOW - AND HOPE I DON'T HAVE TO ACCELERATE IN A CURVE ON INTERSTATE - OR I CAN USE THE RECOMMENDED TIRES - THAT ARE NOT SUITABLE FOR WINTER DRIVING IN KY. FRANKLY, THIS IS A DISASTER WAITING TO HAPPEN. *TR
I BOUGHT A BRAND NEW 2008 BMW X6 IN APRIL 08 AND VARIOUS PROBLEMS KEEP RE-OCCURRING WITH IT. THE MAIN PROBLEM NOW IS THE BACK COVERS OF THE DRIVER AND PASSENGER FRONT SEAT KEEP COMING OUT OF PLACE. IT HAS OCCURRED 3 TIMES IN THE PAST 12 MONTHS. THIS IS A MAJOR SAFETY CONCERN FOR ME IF THE CAR IS IN AN ACCIDENT, THE BACK COVER WOULD LOOSE AND DETACH FROM THE SEAT DURING IMPACT AND CAUSE SERIOUS INJURY TO MY 20 MONTHS CHILD. THE BMW DEALERS REFUSED TO REPAIR THE ISSUE AND CLAIMING THAT THEY ARE ONLY COSMETIC PROBLEMS. BUT THE VEHICLE SHOULD BE RETESTED BY NHTSA FOR THE SEAT ISSUES AND RECALL THE VEHICLES FOR SUCH PROBLEM DUE TO CHILDRENS' SAFETY CONCERNS. *TR
Filed by owners of this model year and unverified by NHTSA — one person’s account, not an established fact.