2011 Mazda Mazda6
Vérifier un véhicule précis
Cette page décrit le modèle. Pour savoir comment une voiture précise est équipée et si son identifiant est valide, décodez son VIN.
Décoder un VINCette page décrit le modèle. Pour savoir comment une voiture précise est équipée et si son identifiant est valide, décodez son VIN.
Décoder un VIN6 rappels et 134 signalements de propriétaires enregistrés pour cette année modèle.
Presque tout ceci décrit l'année modèle, pas la voiture précise. Rien ici ne renseigne sur le kilométrage, les accidents ou la propriété de ce véhicule : aucun identifiant ne les encode.
The contact owns a 2011 Mazda MZ6. The contact stated that while her son was driving at approximately 60-65 MPH, the rear subframe had detached, causing the vehicle to spin across four lanes of traffic and then crash into the median wall. The air bags were not deployed. A police report was filed that listed the cause of failure as a passenger's side rear tire blowout due to cracks along the tire. The contact's son sustained a back injury and medical attention was received. The vehicle was towed to the contact's residence where an independent mechanic diagnosed that the rear subframe had detached. The manufacturer was made aware of the failure and a case was opened. The failure mileage was approximately 200,000.
I WAS IN A CRASH WHERE MY FRONT END WAS EASILY DAMAGED AND PASSENGER AIR BAGS NOT DEPLOYED
HAD AN HEAD ON CAR ACCIDENT ON THE STREET MY TIRE BLOW OUT AND HIT A LIGHT POLE. THE PASSENGER AIR BAG DID NOT COME OUT, ALSO THE DRIVER AIRBAG CAME OUT BUT IT WAS DEFLATED NO AIR WAS IN IT OR WHAT EVER MAKES AN AIR BAG BLOW UP. IN WHICH COST ME TO HIT MY HEAD ON THE STEERING WHEEL.
TAKATA RECALL - 2011 MAZDA 6 I WAS THE PASSENGER IN A COLLISION IN NOVEMBER 2015 WHERE THE 2011 MAZDA 6 WAS T-BONED ON THE DRIVER'S SIDE BY ANOTHER VEHICLE (FORD FUSION), WHICH MADE THE MAZDA 6 SPIN SEVERAL TIMES, HOP A CURB, AND DEPLOY THE AIRBAGS. AS THE PASSENGER (FRONT SEAT) I SUFFERED INJURIES CAUSED BY THE TAKATA AIRBAGS AND REQUIRED GOING TO THE HOSPITAL FOLLOWING THE COLLISION. INJURIES INCLUDED AT LEAST THREE FRACTURED/BROKEN RIBS AND MAJOR BRUISING ON MY RIGHT KNEE. INJURIES TOOK OVER 6 MONTHS TO HEAL, TAKING HEAVY DOSES OF PAIN KILLERS JUST TO MANAGE THE PAIN. LINGERING EFFECTS FROM THIS COLLISION CAN STILL BE FELT 7 MONTHS LATER. THE DRIVER DID NOT SUSTAIN MAJOR INJURIES ASIDE FROM SCRAPES AND A FEW BRUISES. POLICE REPORTS DETERMINED THAT THE DRIVER OF THE FORD FUSION WAS RESPONSIBLE FOR THE COLLISION AND WAS CHARGED WITH CARELESS/RECKLESS DRIVING. THAT DRIVER FAILED TO STOP/YIELD IN THEIR TURNING LANE BEFORE DRIVING STRAIGHT INTO THE MAZDA 6. THE MAZDA 6 WAS DECLARED TOTALED BY INSURANCE. THE MAZDA 6 WAS ADDED TO THE TAKATA AIRBAG RECALL IN MAY 2016, APPROXIMATELY 6 MONTHS AFTER THE ACCIDENT HAD OCCURRED.
TWO CAR COLLISION AT AN INTERSECTION .CITY STREETS. BOTH CARS IN MOTION. AIR BAG DEPLOYED BUT DIDN'T INFLATE. SMOKE FILLED INTERIOR. ATTENDING FIREMAN AT FIRST THOUGHT THE CAR WAS ON FIRE. EXAMINATION SHOWED THAT SMOKE WAS COMING FROM A RUPTURE IN THE AIR BAG NEAR THE POINT WHERE THE BAG WAS CONNECTED TO THE STEERING WHEEL.
TL* THE CONTACT OWNED A 2011 MAZDA 6. WHILE THE VEHICLE WAS SHIFTED INTO REVERSE, IT ACCELERATED ON ITS OWN. THE BRAKE PEDAL WAS ENGAGED, BUT THE VEHICLE CONTINUED TO ACCELERATE AND CRASHED INTO THE GARAGE DOOR. THE DRIVER SUFFERED INJURIES TO THE RIGHT ARM THAT REQUIRED MEDICAL ATTENTION. A POLICE REPORT WAS FILED. THE VEHICLE WAS DESTROYED. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE FAILURE MILEAGE WAS 50,000.
TL* THE CONTACT OWNS A 2011 MAZDA 6. THE CONTACT STATED THE MAIN WIRE HARNESS ON THE DRIVER'S SIDE BURNED OUT AND THE VEHICLE SHOOK WHEN BEING DRIVEN. THE CONTACT WAS CONCERNED THAT THE BURNT WIRE HARNESS COULD CAUSE A FIRE OR CAUSE THE AIR BAGS TO DEPLOY ON THEIR OWN. THE DEALER (BAKERSFIELD MAZDA, 3201 CATTLE DR, BAKERSFIELD, CA 93313) STATED THAT THE VIN WAS NOT INCLUDED IN A RECALL. THE MANUFACTURER WAS NOTIFIED. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE APPROXIMATE FAILURE MILEAGE WAS 58,000.
I WAS ON A STREET IN THE CITY WAITING FOR THE LIGHT TO CHANGE. SUDDENLY I LOST CONTROL OF THE CAR, THE CARD ACCELERATED HIMSELF. I TRY TO AND PUT BRAKE TO THE BOTTOM BUT ANYWAY I HIT THE CAR IN FRONT OF ME. MUCH OF THE FRONT OF MY CAR IS BROKEN. THE OTHER CAR WAS DAMAGED IN THE BACK OF THEIR CAR. THE POLICE MADE A REPORT OF WHAT HAPPENED.
THE RIGHT SIDE OF THE ENGINE CRADLE ROTTED AWAY, CAUSING THE RIGHT LOWER CONTROL ARM TO BREAK AWAY AND LOOSING CONTROL OF THE VEHICLE. I WAS ONLY GOING APPROX. 15 MPH ON A SIDE STREET AND APPLYING THE BRAKES WHEN THIS ACCORDED. THE VEHICLE ONLY HAVE APPROX. 85K MILES ON IT.
The contact owns a 2011 Mazda Mazda6. The contact stated that while driving at an undisclosed speed and coming to a stop, the steering wheel was not operating properly. Several days later while the contact's wife was driving at an undisclosed speed, there was play in the steering wheel. Additionally, there was an abnormal sound coming from the passenger’s side wheel. The contact stated that the wheel was turning abnormally. A mechanic arrived at the residence to diagnose the vehicle and determined that the sub frame was rusted. While touching the sub frame, pieces of the sub frame fractured. The dealer was notified of the failure. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was 92,000.
The contact owns a 2011 Mazda Mazda6. The contact stated that while driving at 25 MPH, the contact attempted to swerve out the way of another vehicle as she suddenly lost control of the vehicle. Due to the failure, the contact force to steer the vehicle to the left as the contact attempted to maintain control of the vehicle. The contact managed to pull over into a parking lot and called her husband for assistance. Despite the failure, the contact managed to drive the vehicle home despite the vehicle being extremely difficult to maneuver. The contact's husband managed to drive the vehicle to a local mechanic, who determined that the front subframe had failed due to excessive corrosion of the subframe. The mechanic then informed the contact of NHTSA Campaign Number: 19V323000 (Structure, Suspension); however, the contact was informed that her vehicle was not included in the recall. The manufacturer was notified of the failure where they confirmed that the vehicle was not included in the recall. The vehicle remained in the mechanic's possession and had yet to be repaired. The failure mileage was 115,000.
Front Subframe has corroded and broke. There is a recall on the subframe that was repaired by dealership in 2019, but this repair did not fix the issue since it has now rusted through and broke. The repair was faulty.
Car developed a known recall issue problem, Recall 2818I. Even though Nebraska was not listed as a "salt state", it's obvious that Nebraska has similar conditions to Iowa. Attempts to contact Mazda USA corporate would not even fix the issue, citing cars age and other factors even though the damage is very specific to this particular recall.
2011 Mazda6 A serious safety defect occurred on my vehicle and matches NHTSA Recall 19V-323 / Mazda Recall 2818I (front cross member corrosion due to insufficient coating) despite this recall not being associated with my VIN. Front cross member cracked due to rust, causing loss of steering control, wheel misalignment, and scraping from the front wheel. This is exactly the failure described in the recall (breakage of the cross member and reduced steering control, increasing the risk of a crash). My safety and the safety of others were put at risk. Although my VIN is not currently associated with the recall, all conditions of the recall apply to my vehicle: -2011 Mazda6 within the affected production range -Defect is a manufacturing issue (insufficient paint coating) -Vehicle was registered in Missouri from 2023-2025, which is a listed state The only reason this recall was not associated with my VIN is because the vehicle was not registered in Missouri at the exact time of the 2019 recall campaign. This is an administrative gap, not a safety distinction. It should not be allowed to limit a manufacturer safety defect to specific states. Vehicles move across state lines constantly. A defect that causes loss of steering control does not stop being dangerous when a car crosses a border. Registration records alone did not reflect actual vehicle use or risk. If recalls are state-limited, manufacturers and NHTSA must continue tracking registration changes and associate the recall with the VIN as soon as a vehicle becomes registered in an affected state. Rust is progressive and age-related. Since this recall began in 2019 and it is now 2026, affected vehicles are more likely to experience failure, and many are now registered in different states than they were in 2019. I am requesting that NHTSA associate Recall 19V-323 with my VIN, investigate the adequacy of state-limited recall tracking, and take action to prevent this known safety defect from causing additional crashes.
When I took the car into my ASE mechanic shop for a normal oil change and tire rotation, they performed a general overall car inspection. They noticed that the Driver Side Rear Subframe had rusted through completely, where the coil spring is located. The passenger side was rusted, but has not yet broke through. They stated that the subframe parts should not rust through like this. They also stated that it is dangerous to drive the car in this condition. I have not notified the manufacturer as of yet, but plan to do so. There were no warning lights, but the ride did seem to be rougher than normal. The attach photos contain 2 photos of the failed driver side rear subframe and 1 photo of the good, passenger side rear subframe.
Déposées par des propriétaires de cette année modèle et non vérifiées par la NHTSA : le témoignage d'une personne, pas un fait établi.
3 rappels comportent un avertissement de ne pas conduire ou de stationner dehors. Vérifiez si ce véhicule a déjà été traité avant de le conduire ou de le garer.
Mazda North American Operations (Mazda) is recalling certain 2007-2012 CX-7, CX-9, and 2009-2012 Maza6 vehicles. These vehicles had their passenger frontal air bag inflators previously replaced under a prior recall using inflators of the same design. The inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Solution : Owners are advised not to drive their vehicles until the repair has been performed. Mazda will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. The recall began December 3, 2019. Owners may contact Mazda customer service at 1-800-222-5500, option 4. Mazda's number for this recall is 1317F. Note: This recall supersedes recalls 16V356 and 17V012.
Mazda North American Operations (Mazda) is recalling certain 2011-2013 Mazda6 vehicles sold, or ever registered in Connecticut, Delaware, the District of Columbia, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland,Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, and Wisconsin. The front cross member may corrode after exposure to road salt.
Solution : Mazda will notify owners, and dealers will inspect the cross member and either install a side member and drain hose and apply wax to protect from rust, or install a drain hose and an improved front cross member, free of charge. The recall began June 13, 2019. Owners may contact Mazda customer service at 1-800-222-5500 Option 4. Mazda's number for this recall is 2818I. Note: This recall is an expansion of Recall 18V-631.
Mazda North American Operations (Mazda) is recalling certain 2014-2015 Mazda CX-9 vehicles sold, or ever registered in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, unless covered in "Zone A," Mazda is recalling certain 2011-2013 Mazda6, 2011-2012 CX-7, and 2011-2015 CX-9 sold, or ever registered in the states of Arizona, Arkansas, Delaware, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, West Virginia and the District of Columbia, or "Zone B." Additionally, unless covered in Zone A or Zone B, Mazda is recalling certain 2010-2013 Mazda6, 2010-2012 CX-7, and 2010-2015 CX-9 vehicles ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C." These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Solution : Mazda will notify owners, and dealers will replace the front passenger air bag inflator with an alternate inflator, free of charge. The recall began November 9, 2018. Owners may contact Mazda customer service at 1-800-222-5500, Option 4. Mazda's number for this recall is 1317F.
Mazda North America Operations (Mazda) is recalling certain 2009-2011 Mazda6, and 2007-2011 CX-7 and CX-9 vehicles. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Solution : Owners are advised not to drive their vehicles until the remedy is performed. Mazda will notify owners, and dealers will replace the passenger frontal air bag inflator with an alternate inflator, free of charge. The recall began on August 30, 2017. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 1317F. Note: This recall supersedes recall 16V356 and all vehicles that were not remedied under that campaign are now covered by this one.
Mazda North America Operations (Mazda) is recalling certain model year 2010-2012 Mazda6 vehicles manufactured September 14, 2009, through May 2, 2011, and equipped with 2.5L engine. In the affected vehicles, spiders may weave a web in the evaporative canister vent hose, blocking it and causing the fuel tank to have an excessive amount of negative pressure.
Solution : Mazda will notify owners, and dealers will reprogram the powertrain control module and inspect and clean the canister vent line. If a web was found in the line, the fuel tank and check valve on canister vent line will be replaced. These repairs will be done free of charge. The recall began on April 30, 2014. Owners may contact Mazda at 1-800-222-5500. Mazda's recall number associated with this campaign is 7214C.
Mazda is recalling certain model year 2009-2013 Mazda6 vehicles manufactured February 4, 2008, through August 24, 2012. The door latch mounting screws may become loose.
Solution : Mazda will notify owners, and dealers will apply a thread locking adhesive to the door screws and retorque them, free of charge. The recall began on October 29, 2013. Owners may contact Mazda at 1-800-222-5500. Mazda's recall number is 7013I.
Publiés par année modèle et non par VIN : ils peuvent ne pas concerner ce véhicule, ou avoir déjà été effectués. À confirmer auprès d'un concessionnaire.