7 rappels et 52 signalements de propriétaires enregistrés pour cette année modèle.
Cette page décrit le modèle. Pour savoir comment une voiture précise est équipée et si son identifiant est valide, décodez son VIN.
Décoder un VINPresque tout ceci décrit l'année modèle, pas la voiture précise. Rien ici ne renseigne sur le kilométrage, les accidents ou la propriété de ce véhicule : aucun identifiant ne les encode.
My car had an accident and it was hit by another car on the left side, but the camera which was assumed to record the accident, it did not. Fortunately no one get injury. But I have to pay with my insurance. BWM did not admit such fatal error. I talked to them but they said I can sue them.... 1. I went to BMW Darien, the specilist said the camera only worked when being hit by the front, but it is not true, there are 4 cameras which record 360 degree around. 2. I assumed whenever an accident happened, the camera system will be activated, but the BMW people said because the accident was not severe, then the sensors did not work. But when checking my car, the whole left side was damaged, it is not a minor hit. Thus I question how severe would it be sufficient to trigger the system. 3. I have not been to the dealer. 4. The insurance just checked the damage and send me an estimated amount to repair the car. 5. there is no message, or because I was not the driver, I did not know.
Collision warning failed. Automatic emergency braking failed. Unknown if brakes were delayed or had issue stopping. I rear ended the car the in front of me, going from a stop while attempting to make a right hand turn. There were no system warnings or emergency braking applied although the car is equipped with those and many more safety features. During the accident the air bags were not deployed. So the impact was not severe but caused a combined $10,000 plus in cosmetic damage to both vehicles.
The contact owns a 2024 BMW X7. The contact received notification of NHTSA Campaign Number: 24V104000 (Electronic Stability Control(ESC), Service Brakes, Hydraulic); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.
The contact owns a 2024 BMW X7. The contact received notification of NHTSA Campaign Number: 24V104000 (ELECTRONIC STABILITY CONTROL (ESC), SERVICE BRAKES, HYDRAULIC); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available .
The contact owns a 2024 BMW X7. The contact received notification of NHTSA Campaign Number: 24V104000 (Electronic Stability Control (ESC), Service Brakes, Hydraulic); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was contacted. The manufacturer was not made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.
Outstanding recall that the manufacturer has failed or is unable to remedy in a timely manner.
While driving northbound on [XXX] near West Greenwich, RI with my wife and two young children, the front sunroof glass of our 2024 BMW X7 spontaneously exploded at highway speed. There were no overhead structures or nearby vehicles that could have caused an impact. Conditions were slightly rainy. Approximately one week before this event, the vehicle displayed a warning that the sunroof was “not initialized.” I followed the reset procedure, and the message cleared. It’s unclear if that alert was related, but the sunroof’s failure seems more than coincidental. The explosion caused loud noise, exposure to weather, and panic inside the cabin. Fortunately, the cloth sunshade was closed and minimized glass intrusion. We pulled off the highway, documented the damage, and temporarily sealed the roof using materials from a local hardware store. BMW has not yet confirmed whether this repair will be covered under warranty. We were forced to fly home due to lack of a functioning vehicle. I am reporting this because it was a serious safety issue that could have resulted in greater harm under slightly different circumstances. Please investigate this issue further as it appears similar to other spontaneous sunroof failures reported in recent years. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
The contact owns a 2024 BMW X7. The contact stated that after test driving a similar vehicle, the contact decided to purchase a similar vehicle; however, while writing up the contract, the salesperson added the incorrect VIN on the sales contract. The contact had been receiving notification of NHTSA Campaign Number: 24V104000 (Electronic Stability Control (ESC), Service Brake, Hydraulic); however, the VIN listed on the recall notice was for the vehicle test driven, not the actual vehicle that was purchased. The contact had not yet received a recall notification for the vehicle owned. The contact requested to be removed from the recall distribution list for the incorrect VIN, and for the correct VIN to be added. The local dealer was contacted. The manufacturer was made aware of the issue but offered no assistance.
Cannot safety drive the car with the major recall on the braking system. I have slid through intersections trying to brake - thankfully no other cars were present at the time. No remedy or solution has been offered and BMW refuses to order the part or allow trade-in on the vehicle.
The contact owns a 2024 BMW X7. The contact received notification of NHTSA Campaign Number: 24V104000 (ELECTRONIC STABILITY CONTROL (ESC), SERVICE BRAKES, HYDRAULIC); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was made aware of the issue. The manufacturer was not made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.
2024 X7 with 13k miles on it roughly. Have had multiple drivetrain malfunction issues that caused car to not start. Dealer first did a software update which i dont believe fixed anything. second time the issue happened they said it was due to the car battery not being charged enough. car has had multiple issues related to low charge. BMW says its due to me not taking the car on long enough drives. However the charging on the car is inconsistent and faults related to the 48volt charging system which have stated (repair required soon) 224F8F were cleared by the dealer and not investigated. Car has many times exhibited low battery issues with electronics being sporatic and unreliable. car will sometimes charge battery on short drives and other times will not charge the battery on long/normal drives. charging is inconsistent. Many people on BMW forums have had drivetrain malfunction errors [XXX] and in some cases bmw has replaced transmissions. however i believe an investigation is warranted as the dealership in my case is just clearing codes and not repairing the car. i believe there is an issue with the charging system on the car thats causing errors in other modules/sensors based on all the issues i have had with this car. i have brought the car in for at least 10 service visits. BMW continues to clear codes and not perform thorough investigation and look at history of vehicle. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
I’ve had multiple issues starting with a left tail light/left brake malfunction. Took my vehicle into Sewell Grapevine and they replaced the left taillight and module. After picking up my vehicle, I began having issues with my dash within a couple days of the repair mentioned above. The assisted parking began turning on by itself when the vehicle came to a complete stop. This happened multiple times while driving. I have multiple videos. I uploaded a screen shot. The dash also turned black. Returned my vehicle to Sewell, they said they recalibrated the rear view mirror and checked the connections. On [XXX] while driving home, the vehicle had an inability to drive sos call emergency services malfunction come up multiple times. The car lost all power and the steering wheel was trying to correct the vehicle until you lifted your foot off the gas peddle. This also happened multiple times while spring in excess of 70 mph on the freeway. As of today, Feb 26, 2025, my vehicle is currently at Sewell in Grapevine, Tx with no plan from the dealership on how to correct these issues. This is the second X7, same body style, that I have owned with serious safety issues like this. Sewell Grapevine had to buy back the first vehicle as they were unable to repair the first one. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
Car presents the forward collision mitigation and lane departure warning are inoperable. Errors popped up 10-20 times while driving a short distance. These are repeat errors that BMW has not fixed. As i drove the car kept alerting me that the systems were offline. They would come back online and go back offline as i drove. Car has been to dealership around 8-9 times and BMW says there is adamant that nothing is wrong with the car even though this error has been happening since I have had the car at around 1000 miles. Currently at ~13k miles now.
Multiple times when my 2024 X7 has started or I have been driving a warning message pops up that states that Forward Collision Mitigation or other safety systems are "reduced". BMW has stated there is nothing to fix on the car.
The door lock actuator for the front driver door failed twice. The first time it failed, the car would not unlock from the outside. All other doors would unlock. I had my kids in the back of the car and I was trying to get inside the car to drive and it wouldn't open. I had to pry off the cap covering the keyhole on the door with a screwdriver and then insert the blade key and manually turn the actuator. I got this failed unlocking on video and submitted it to BMW. They claimed they could not replicate and that there was no issue with the door and gave me the car back without fixing anything. A short time later I was parked at the grocery store, this time inside the car, and the car door wouldnt open. I pulled on the inside handle and there was a lot of resistance to it. I had to yank on it pretty hard and finally the door popped open. I then tried to close the door but there was no resistance on the latch and the door would no longer close. I called BMW roadside and they instructed me to pull the handle on the outside three time and the inside three times and this would fix the door. This did not work and they had to tow the car. I had to drive the car home while holding the door closed because I needed to get to our other car and move the car seats over for my [XXX] and [XXX] . BMW currently has the car now and they said the actuator has failed and they are replacing it. BMW refused to fix the car when presented with a video of the non-functioning door latch/lock until it left the car in an unsafe manner where the car door would swing open and never close. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
Déposées par des propriétaires de cette année modèle et non vérifiées par la NHTSA : le témoignage d'une personne, pas un fait établi.
Water may come into contact with the starter relay and gradually cause corrosion. This could affect the electrical connection inside the relay and make the engine difficult to start. It may also result in a short circuit and could cause the starter to overheat leading to a fire when the vehicle is in motion or when it is parked with the ignition off. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The engine starter’s electrical contacts may overheat and cause the vehicle to start improperly. Continued starting attempts can intensify the overheating and ignite surrounding components, potentially leading to a vehicle fire while driving or shortly after parking. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The hollow shaft of the servomotor was not welded correctly. The weld may not be able to withstand high braking pressure build-up and may break. In this case, the reduced braking performance requires greater force and the braking distance may increase. In addition, the ABS and DSC brake control systems are not assisted. This increases the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The software-based overload protection function cannot sufficiently prevent the starter being overloaded in the event of repeated long start-up attempts. The starter may overheat or sparks may be produced as a result of an increased current flow. This increases the risk of a fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The gas generator in knee airbag modules was not properly inserted into the air cushion, resulting in the cushion failing to unfold sufficiently. As a result, it may not be able to deploy correctly in the event of an accident, leading to a reduction in the restraint effect, increasing the risk of injury to the occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The integrated braking system could be compromised, which could lead to an unexpected failure of the hydraulic braking assistance, thereby requiring greater pressure on the brake pedal. This can result in a longer braking distance, as well as failure of the Anti-lock Braking System (ABS) and the Dynamic Stability Control (DSC), increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The dashboard in the affected vehicles may not have been manufactured to the manufacturer specifications. In the event of anaccident, the passenger side airbag may not deploy as intended which could increase the risk of injury to the frontpassenger. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Rapprochés par marque et nom de modèle — Safety Gate ne publie pas de VIN. Vérifiez les dates de production et indiquez le code de rappel au concessionnaire.
BMW of North America, LLC (BMW) is recalling certain 2025 Mini Cooper S, Mini Countryman S All4, X2, 2024 Rolls-Royce Spectre, 2023-2025 i7, 7 Series, X7, 2024-2025 i5, 5 Series, 2023-2024 XM, X1, 2024-2025 X6, and X5 vehicles. The integrated brake (IB) system may malfunction and result in a loss of power brake assist or cause the Antilock Brake (ABS) and Dynamic Stability Control (DSC) systems to not function properly.
Solution : The Integrated brake system will be inspected and, if necessary, replaced, free of charge. Owner notification letters are expected to be mailed August 21, 2026. Owners may contact BMW customer service at 1-800-525-7417 or Rolls-Royce customer service at 1-877-877-3735. Vehicle Identification Numbers (VINs) involved in this recall will become searchable on NHTSA.gov beginning August 21, 2026. Vehicles previously repaired under recall 24V739 or 24V104 will need to have the new remedy completed.
BMW of North America, LLC. (BMW) is recalling certain 2023-2024 X1, X5, X6, X7, XM, 530i, i5, 740i, 760i, i7, and 750e vehicles. Please see the recall report for a complete list of models and model years. The integrated brake (IB) system may malfunction and result in a loss of power brake assist or cause the Antilock Brake (ABS) and Dynamic Stability Control (DSC) systems to not function properly.
Solution : Dealers will replace the integrated brake module, free of charge. Interim owner notification letters notifying owners of the safety risk are expected to be mailed November 22, 2024. Second letters will be mailed once the parts are available. Owners may contact BMW customer service at 1-800-525-7417. Vehicles in this recall were previously repaired under recall number 24V-104 and will need to have the new remedy completed.
BMW of North America (BMW) is recalling certain 2023-2024 X1, 2024-2025 X5, 2025 X6, 2023-2025 X7, 740i, 760i, 2024 XM, 530i, 540i, i7, 750e, X2, 2024-2025 i5, 2024 Rolls Royce Spectre, 2025 MINI Countryman S ALL4, JCW Countryman ALL4, and 2025 MINI Hardtop 2 Door (Cooper, Cooper S) vehicles. Please refer to the recall report for the complete list of models. The welds in the servomotor of the integrated brake control module may break, causing a loss of power brake assist and rear brake function. In addition, the Antilock Brake System (ABS) and Dynamic Stability Control (DSC) system may not function.
Solution : Dealers will replace the integrated brake system, free of charge. Owner notification letters were mailed November 13, 2024. Owners can contact BMW Customer Service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2024 X5 sDrive40i, X5 xDrive40i and X7 xDrive40i vehicles. The instrument panel may not have been manufactured properly, which can result in improper air bag deployment or the panel separating during air bag deployment.
Solution : Dealers will replace the instrument panel, free of charge. Owner notification letters were mailed April 16, 2024. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC. (BMW) is recalling certain 2023-2025 BMW, MINI, and Rolls-Royce vehicles. Please see the recall report for a complete list of models and model years. The integrated brake (IB) system may malfunction and result in a loss of power brake assist or cause the Antilock Brake (ABS) and Dynamic Stability Control (DSC) systems to not function properly.
Solution : Dealers will replace the integrated brake system, free of charge. Owner notification letters were mailed between June and December 2024. Owners may contact BMW customer service at 1-800-525-7417 or Rolls Royce customer service at 1-877-877-3735.
BMW of North America, LLC (BMW) is recalling certain 2023 BMW XM, 2024 BMW X5 sDrive40i, X5 xDrive40i, X5 M60i, X5 M, X5 xDrive50e, X6 xDrive40i, X6 M60i, X6 M, X7 xDrive40i, X7 M60i, and Alpina XB7 vehicles. The front passenger knee air bag may not deploy as intended.
Solution : Dealers will replace the front passenger knee air bag, free of charge. Owner notification letters were mailed November 3, 2023. Owners may contact BMW's customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2024 X5 sDrive40i, X5 xDrive40i, X5 M60i, X5 M, xDrive 50e, 2024 X6 xDrive40i, X6 M60i, X6 M, 2024 X7 xDrive40i, X7 M60i, Alpina XB7, and 2023 XM vehicles. The knee air bag (driver and/or passenger) may not have been manufactured correctly, which can result in the knee air bag not deploying as intended.
Solution : Dealers will replace the knee air bag (driver and/or passenger), free of charge. Owner notification letters were mailed September 6, 2023. Owners may contact BMW customer service at 1-800-525-7417.
Publiés par année modèle et non par VIN : ils peuvent ne pas concerner ce véhicule, ou avoir déjà été effectués. À confirmer auprès d'un concessionnaire.