4 llamadas a revisión y 85 quejas de propietarios registrados para este año del modelo.
Esta página describe el modelo. Para ver cómo está equipado un coche concreto y si su identificador es válido, decodifica su VIN.
Decodificar un VINCasi todo esto describe el año del modelo, no el coche concreto. Nada de aquí dice nada sobre el kilometraje, los accidentes o la titularidad de este vehículo: ningún identificador los codifica.
TL* TAKATA RECALL. THE CONTACT OWNS A 2010 BMW X3 SAV. THE CONTACT STATED THAT THE VEHICLE STALLED WITHOUT WARNING IN THE MIDDLE OF THREE LANES OF TRAFFIC. THE CONTACT EXITED THE VEHICLE WHILE THE PASSENGER REMAINED INSIDE. ANOTHER VEHICLE DRIVING AT A HIGH RATE OF SPEED CRASHED INTO THE REAR OF THE CONTACT'S VEHICLE, PUSHED THE VEHICLE TO THE LEFT, AND CAUSED IT TO CRASH INTO A CURB. THE AIR BAGS DID NOT DEPLOY. THE DRIVER WAS NOT INJURED. THE FRONT PASSENGER SUSTAINED MAJOR INJURIES TO THE BACK, SHOULDER, AND NECK. MEDICAL ATTENTION WAS REQUIRED. A POLICE REPORT WAS FILED. THE VEHICLE WAS TOWED TO A REPAIR SHOP AND THE BODY DAMAGE WAS REPAIRED. THE VEHICLE WAS TOWED TO THE DEALER WHERE THE VANOS HOUSING BOLTS WERE SUPPOSEDLY REPLACED. THE VIN WAS INCLUDED IN NHTSA CAMPAIGN NUMBER: 16V071000 (AIR BAGS). THE CONTACT RECEIVED NOTIFICATION OF A MANUFACTURER RECALL FOR NHTSA CAMPAIGN NUMBER: 14V176000 (ENGINE AND ENGINE COOLING). THE MANUFACTURER WAS NOTIFIED, BUT HAD NOT CALLED THE CONTACT BACK. THE FAILURE MILEAGE WAS NOT AVAILABLE. PARTS DISTRIBUTION DISCONNECT.
No warnings. The car started smoking while driving down the interstate. Lost electrical and brakes at around 30 mph while trying to stop. My daughter had to roll out of the car while moving because my brakes wouldn’t stop. Finally slammed in park. Car was totaled.
THE DRIVER'S SEAT HEATER MALFUNCTION. THE SEAT OVER HEATED AND A HOLE WAS CREATED AS A RESULT OF BURN ON TOP OF THE COIL.
IN MOTION WHEN IT STARTED SMOKING. STATIONARY WHEN IT WENT UP IN FLAMES
TL* THE CONTACT OWNS A 2010 BMW 3 SERIES. THE CONTACT STATED THAT WHILE DRIVING APPROXIMATELY 20 MPH, SMOKE STARTED TO EMIT FROM THE FRONT DRIVER SIDE OF THE VEHICLE. THE VEHICLE WAS MERGED TO THE SIDE OF THE ROAD IN ORDER TO INSPECT THE VEHICLE. THE CONTACT STATED THAT ONCE THE HOOD OF VEHICLE WAS OPEN, HE OBSERVED FLAMES COMING FROM THE ENGINE. THE CONTACT EXTINGUISHED THE FIRE. THE VEHICLE WAS TOWED TO A DEALER WHO STATED THE EMISSION VALVE OVERHEATED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE FAILURE MILEAGE WAS 38,000.
I HAVE BEEN DRIVING FOR OVER 2 YEARS WITH DEFECTIVE AIR BAGS (FRONT). I HAVE RECEIVED MANY NOTICES ABOUT THIS BUT NO RESULTS. THE FIRST NOTICE SAID "IN THE EVENT OF A CRASH NECESSITATING DEPLOYMENT OF THE DRIVER'S FRONT AIR BAG, EXCESSIVE IONTERNAL PRESSURE COULD CAUSE RUPTURING OF THE AIR BAG INFLATOR, RESULTING IN METAL FRAGMENTS STRIKING THE DRIVER OR OTHER PASSENGERS POTENTIALLY RESULTING IN SERIOUS INJURY OR DEATH. I WAS INVOLVED IN A REAR END COLLISION AND MY AIR BAG DID NOT DEPLOY!!!!!! I HAVE ADVISED MY ATTORNEY OF THIS RECALL ( OVER 2 YEARS) IN CASE I AM KILLED BY THIS DEFECTIVE AIR BAG.
DRIVING FROM WORK ON A SNOWING DAY, GOING ABOUT 25 TO 35. THE REAR OF THE CAR STARTED GOING TO THE OTHER SIDE OF LANE. I TRADED TO GET CONTROL BUT IT WAS TO LATE. I HIT A GUARD RAIL AND THE AIR BAGS NEVER CAME OUT. *TR
The contact owns a 2010 BMW X3. The contact stated that after the dealer had performed the recall repair of NHTSA Campaign Number: 22V119000 (Engine and Engine Cooling); the vehicle experienced a significant rough idle, and abnormal whistling and squealing sounds were coming from the engine while the contact was driving from the dealer parking lot. The contact drove back to the dealer, where it was diagnosed that the new PCV valve cover gasket had caused a vacuum leak. The dealer related the failure to the recall remedy. The dealer charged a fee for the repair. The contact declined to pay the fee because the recall repair was the cause of the failure. The contact stated that the vehicle had not experienced a failure before the recall repair. The vehicle was not repaired. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was 119,940.
The contact owns a 2010 BMW X3. The contact received notification of NHTSA Campaign Number: 23V707000 (Engine and Engine Cooling); however, the part to do the recall repair was not yet available. The contact stated that while starting the vehicle, several unknown warning lights illuminated, and the vehicle was shuddering. The contact stated that the failure persisted while driving, and the vehicle decelerated unintendedly on several occasions. The local dealer was contacted. The vehicle was not diagnosed or repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the failure. The failure mileage was approximately 120,000. VIN tool confirms parts not available.
The contact owns a 2010 BMW X3. The contact received notification of NHTSA Campaign Number: 23V707000 (Engine and Engine Cooling); however, the part to do the recall repair was not yet available. The contact stated that while driving at various speeds and depressing the accelerator pedal, the vehicle hesitated to respond. The contact also stated that the vehicle made an abnormal rattling while the engine revved between 2000-3000 RPMs. Additionally, the contact stated that the vehicle stalled on cold idles. The contact was able to restart the vehicle. There was no warning light illuminated. The local dealer was contacted. The vehicle was not diagnosed or repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure. The failure mileage was approximately 100,000. VIN tool confirms parts not available.
The contact owns a 2010 BMW X3. The contact received notification of NHTSA Campaign Number: 23V707000 (Engine and Engine Cooling); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.
The contact owns a 2010 BMW X3. The contact stated that while driving at various speeds and while the vehicle was idling, there was an abnormal rattling sound coming from the vehicle. The check engine light warning light was illuminated. Additionally, the vehicle hesitated while depressing the accelerator pedal. The contact received notification of NHTSA Campaign Number: 23V707000 (Engine and Engine Cooling) however, the part to do the recall repair was not yet available. The local dealer was made aware of the issue and confirmed that parts were not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The failure mileage was approximately 120,000. VIN tool confirms parts not available.
The contact owns a 2010 BMW X3. The contact received notification of NHTSA Campaign Number: 23V707000 (Engine and Engine Cooling) however, the part to do the recall repair was not yet available. The local dealer was not contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.
The contact owns a 2010 BMW X3. The contact received notification of NHTSA Campaign Number: 23V707000 (Engine and Engine Cooling) however, the part to do the recall repair was not yet available. The local dealer was contacted, and it was confirmed that the part was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact stated that the vehicle had stalled and lost motive power while driving. The vehicle was not diagnosed or repaired. The failure mileage was 130,000. VIN tool confirms parts not available.
BMW is not addressing this recall in a timely manner. The history makes me think they're intentionally stalling the process and allowing customer engines to fail, reducing repair loads on their service centers. This VANOS bolt issue has been well-known and wide-spread for over a decade (see [XXX] for example), and BMW has been selectively recalling very narrow ranges of engines over this period. Now, they are claiming that parts are unavailable for this recall issued in Oct 2023 - 6 months ago. When I called their corporate office, they claimed parts should be available "any day now. 7-10 at the most," with no further explanation. My engine could blow up on the road at any moment. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
Presentadas por propietarios de este año del modelo y sin verificar por la NHTSA: el relato de una persona, no un hecho probado.
BMW of North America, LLC (BMW) is recalling certain 2010-2012 1 Series Coupe, 1 Series Convertible, 3 Series Sedan, 3 Series Convertible, 2010-2011 3 Series Sportswagon, 3 Series Coupe, 5 Series Sedan, X3 xDrive 28i, X3 xDrive 30i, X5 xDrive30i, and Z4 sDrive30i vehicles. The aluminum bolts that secure the housing for the variable camshaft timing adjustment (VANOS) unit can loosen over time and possibly break.
Solución: Dealers will replace the four VANOS bolts, free of charge. Interim letters notifying owners of the safety risk are expected to be mailed December 18, 2023. Owner notification letters were mailed June 19, 2024. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2008-2013 128i and 135i Convertibles, 128i, 135i, and M Coupes, 2007-2010 X3 30si and X3 xDrive30i, 2013-2015 X1 sDrive28i, X1 xDrive28i and X1 xDrive35i, 2007-2013 328i, 328i xDrive, 335i, 335is, 335i xDrive and M3 Coupes, 2006-2011 328i, 328xi, 328i xDrive, 325i, 325xi, 330i, 330xi, 335i, 335xi, 335i xDrive and M3, 2009-2011 335D, 2006-2012 325xi, 328i, 328xi and 328i xDrive, 2010-2011 X6 ActiveHybrid, 2007-2013 328i, 335i, 335is, M3 Coupes, X5 30si, X5 xDrive30i, X5 xDrive35i, X5 48i, X5 xDrive48i, X5 xDrive50i and X5 M, 2009-2013 X5 xDrive35d and 2008-2014 X6 xDrive35i, X6 xDrive50i and X6M vehicles equipped with non-desiccated driver frontal air bag inflators containing phase stabilized ammonium nitrate (PSAN) that were used as interim remedy parts for previous Takata recalls. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Solución: BMW will notify owners, and dealers will replace the driver air bag. On X5 and X6 vehicles, only the inflator will be replaced. All repairs will be performed free of charge. The recall began March 11, 2020. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2008-2011 128i and 2007-2011 328i, 328xi, 328i xDrive, 525i, 525xi, 528i, 528xi, 530i, 530xi, X3 3.0si, X3 xDrive30i, X5 xDrive30i, Z4 3.0i, Z4 3.0si and Z4 sDrive30i vehicles. The heater for the positive crankcase ventilation (PCV) valve may short circuit.
Solución: BMW will notify owners, and dealers will replace the PCV valve heater, free of charge. Interim letters were mailed on November 27, 2017. Owners will receive a second notification by the end of October 2018. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2006-2010 BMW X3 2.5i, X3 3.0i and X3 xDrive30i Sports Activity Vehicles. The front passenger seat occupant detection mat that determines if, and how, the passenger frontal air bag should deploy in a crash may fatigue and develop cracks which could lead to a system failure.
Solución: BMW will notify owners, and dealers will replace the front passenger seat occupant detection mat, free of charge. Interim owner notification letters were mailed on November 27, 2017. A second notification letter will be sent when parts are available. Owners may contact BMW customer service at 1-800-525-7417.
Publicadas por año del modelo, no por VIN: pueden no afectar a este vehículo o ya estar resueltas. Confírmalo con un concesionario.
Water may come into contact with the starter relay and gradually cause corrosion. This could affect the electrical connection inside the relay and make the engine difficult to start. It may also result in a short circuit and could cause the starter to overheat leading to a fire when the vehicle is in motion or when it is parked with the ignition off. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Due to a manufacturing failure, the protection of the two outer headrests in the second row is reduced. In the event of a collision or accident, passengers could be injured. In addition, headrest parts may become exposed and also cause serious injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The RSW22 starter with reinforced water tightness (RWT) may experience increased abrasion of the magnetic contact, causing deposits to build up at the lowest point inside the relay. These deposits may increase relay contact resistance, leading to starting failures or short circuits. If a short circuit occurs, either when attempting to start the vehicle or while driving due to vibration-related movement of the deposits, it could cause a thermal event and increase the risk of fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Damaged brake discs may have been fitted to the front axle. This can lead the brakes to fail when a heavy load is placed on the wheel concerned, increasing the risk of accident and injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Failure to bolt the plus voltage (B+) cable tightly enough to the starter generator may result in contact problems and an increase in contact resistance at the bolted connection. This may in turn lead to local overheating and the vehicle catching fire or to the engine stalling while the vehicle is coasting. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The positive battery cable of the starter-generator may not have been manufactured correctly. This could result in a loose electrical connection, leading to excessive contact resistance. The vehicle cannot charge or start. Contact points in the starter-generator could overheat and cause a vehicle fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the inflator of the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments of the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The driver airbag inflator may malfunction due to long-term degradation. In this case, if the airbag is deployed in an accident, the internal pressure in the inflator may be too high. The inflator could burst. Metal fragments may cause injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The failure concerns the RSW22 starter, type RWT (reinforced for watertightness). Increased abrasion of the magnetic contact can lead to the formation of deposits at the lowest point of the relay interior. This in turn can increase the resistance of the relay contact, causing accidental ignition or even short circuits, possibly leading to a thermal reaction and fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The failure concerns the RSW22 starter, type RWT (reinforced for watertightness). Increased abrasion of the magnetic contact can lead to the formation of deposits at the lowest point of the relay interior. This in turn can increase the resistance of the relay contact, causing accidental ignition or even short circuits, possibly leading to a thermal reaction and fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The failure concerns the RSW22 starter, type RWT (reinforced for watertightness). Increased abrasion of the magnetic contact can lead to the formation of deposits at the lowest point of the relay interior. This in turn can increase the resistance of the relay contact, causing accidental ignition or even short circuits, possibly leading to a thermal reaction and fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The steering system sensor may malfunction causing an unintended steering movement of the vehicle. This increases the risk of accidents and injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The screw connection of the servo unit on the gear rack casing of the steering system may be faulty. This could cause the steering system to fail and become blocked, increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Due to faulty rear-most screws, the screw fixings of the boot's lashing rails can fail in the event of a rear-end collision with heavy intrusion and penetrate the backs of the rear seats. This increases the risk of injury to the occupants of the rear seats. The vehicles concerned have already been modified in connection with the recall code 0051960500. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant within the integrated inflator of driver airbags can deteriorate during time. If the airbag deploys, it could result in fragments from the inflator casing injuring the vehicle’s occupants. The product does not comply with the Regulation on the approval and market surveillance of Motor Vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Due to faulty rear-most screws, the screw fixings of the boot's lashing rails can fail in the event of a rear-end collision with heavy intrusion, and penetrate the backs of the rear seats. This increases the risk of injury to the occupants of the rear seats. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
A seam on the inflator housing of the driver airbag may not have been correctly welded. In case of accident, when the airbag is deployed, the inflator can burst, releasing metal parts which could cause injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The driver's airbag inflator propellant may deteriorate over time. If activated during an accident, excessive internal pressure may cause the inflator to burst, and metal fragments could pass through the cushion material causing injury to occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Due to a manufacturing error, the weld seam of the integrated transmission control unit (ITCU) may not have been correctly executed. As a result, transmission oil could leak into the ITCU, causing it to fail. This may lead to transmission seizure, increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Emparejadas por marca y nombre de modelo: Safety Gate no publica el VIN. Comprueba las fechas de fabricación y facilita el código de la llamada al concesionario.