2 llamadas a revisión y 345 quejas de propietarios registrados para este año del modelo.
Esta página describe el modelo. Para ver cómo está equipado un coche concreto y si su identificador es válido, decodifica su VIN.
Decodificar un VINCasi todo esto describe el año del modelo, no el coche concreto. Nada de aquí dice nada sobre el kilometraje, los accidentes o la titularidad de este vehículo: ningún identificador los codifica.
2006 BMW 330XI BRAKE FAILURE, ACCELERATION, NO STEERING. OCCURRED TWICE; BMW REPAIRED BY DEALER NEW BRAKES, COMPUTER; SECOND OCCURRENCE CAR DID NOT STOP UNTIL HIT TREES. *TR
2006 BMW 330 XI WHEN PRESSING ON THE BRAKE THE CAR ACCELERATED WITH A LOUD NOISE, COULD NOT STEER THE CAR; CRASHED IN TREES. 24,323 MILES STILL UNDER NEW CAR WARRANTY. *TR
HEATED SEAT MALFUNCTIONS CAUSING "HOT SPOT" THAT BURNS SKIN ON REAR UPPER LEG.
DRIVER'S SIDE SEAT HEATER WIRE BURNED THROUGH THE SEAT, MELTED A SPOT ON MY VINYL RAINCOAT AND SUBSEQUENTLY BURNED MY BUTTOCK. VEHICLE WAS IN MOTION ON A CITY STREET AT THE TIME.
AS I DROVE HOME FROM A LONG FLIGHT HOME AFTER THE HOLIDAYS, THE ENGINE CAUGHT FIRE DUE TO A FROZEN CRANK CASE VENTILATION SYSTEM WHICH CAUSED OIL TO SPRAY OUT IN THE ENGINE COMPARTMENT. I PULLED OVER WHEN I NOTICED SMOKE IN THE PASSENGER COMPARTMENT AND SMOKE COMING OUT OF THE HOOD. I WAS ABLE TO BLOW OUT THE FIRE. TEMPERATURES WERE 5 DEGREES F THAT NIGHT. THE DEALER STATED THERE WAS A "MORE ROBUST CRANK CASE VENTILATION SYSTEM" THAT THEY WOULD INSTALL AT MY COST. AFTER THE WEEK LONG REPAIR, THE DEALER BROUGHT MY CAR TO THE FRONT AND TURNED ON THE SEAT HEATERS. I DROVE ABOUT 5 MILES BEFORE NOTING A PINCHING/PAINFUL SENSATION ON MY LEFT UPPER THIGH. I PULLED OVER TO FIND A BURN MARK ON THE LEATHER SEAT AND A BURN ON MY LEFT UPPER THIGH. IT APPEARS TO BE DUE TO A SHORT IN THE SEAT HEATER.
TL* THE CONTACT OWNS A 2006 BMW X3. WHILE DRIVING 55 MPH, THE PASSENGER SEAT WARMER BECAME EXTREMELY HOT AND BURNED THE PASSENGER'S LEG. THE WIRING BEGAN TO SMOKE AND THE CONTACT OBERVED A SPARK. NO MEDICAL ATTENTION WAS REQUIRED. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE VIN WAS INVALID. THE FAILURE MILEAGE WAS APPROXIMATELY 115,967.
DRIVER SEAT CAUGHT FIRE WHEN SEAT WARMER WAS ENGAGED. LEATHER SEAT HAS VISIBLE BURN MARK. FIRE BURNED DRIVER. WHEN SEAT WARMER WAS DISENGAGED, SMOKE BEGAN BILLOWING FROM SEAT, FILLING THE VEHICLE WITH SMOKE. SEAT WARMER WAS ENGAGED UPON VEHICLE START IN OWNER'S GARAGE. VEHICLE WAS MOVING APPROXIMATELY 10 MPS (1-2 MINS LATER) WHEN FIRE BEGAN. *TT
TL*THE CONTACT OWNS A 2006 BMW X3. WHILE DRIVING APPROXIMATELY 45 MPH THE HEATER ON THE DRIVERS SEAT MALFUNCTIONED AND BURNED A HOLE IN THE SEAT. AS A RESULT THE DRIVER WAS INJURED. THE DEALER WAS CONTACTED AND STATED THAT THEY WOULD NOT COVER THE REPAIR COST BECAUSE THE WARRANTY EXPIRED. THE VEHICLE WAS NOT TAKEN TO THE DEALER FOR REPAIRS. THE APPROXIMATE FAILURE MILEAGE WAS 60,000.
The contact owns a 2006 BMW X3. The contact stated that while driving at 30 MPH, the contact rear-ended another vehicle. All the air bags except for the passenger’s side air bag deployed upon impact. The contact suffered a migraine from the collision but did not receive medical attention but planned to go to urgent care afterward. A police report was filed. The vehicle was towed to the contact's residence. The vehicle was not totaled. The manufacturer was not made aware of the failure. Prior to the failure, the dealer serviced the recall under NHTSA Campaign Number: 17V605000 (Air Bags). The failure mileage was approximately 130,000.
ON 8/4/2016 AROUND 7:20AM. I PULLED INTO A PARKING SPACE AT WORK. MY FOOT WAS ON THE BRAKE AND WAS A COMPLETE STOP. SHIFTING FROM DRIVE TO PARK. THE CAR EXCELERATED THROWING ME BACK INTO MY SEAT. I KEPT PUSHING THE BRAKE AND THE CAR WOULD NOT STOP. THE CAR WENT AIRBORNE AND EXCELERATED A SECOND TIME. I HIT A FIRE HYDRANT AND LANDED IN THE STREET. I WAS THEN ABLE TO STOP THE CAR. THE DISTANCE FROM THE PARKING STOP TO THE ROAD WAS ABOUT 20 FEET. THE CAR WAS TOWED TO A BMW DEALER. BMW HAD MY CAR FOR 8 WEEKS. THEY HAD 2 DIFFERENT TECHS COME IN TO LOOK AT THE CAR. THE OUT COME WAS THAT THE BRAKES ARE FINE AND IT DID NOT HAVE ANY CODES. NOTHING IS WRONG WITH THE CAR. I TOLD THEM THAT I DIDN'T WANT THE CAR BACK. SINCE THEY DIDN'T SEE AN ISSUE I TOLD THEM I WOULD TRADE IT IN AND THEY COULD BE LIABLE FOR SOMEONE ELSE GETTING HURT. FUNNY HOW ALL OF THE SUDDEN THEY TOTALED OUT THE CAR. I ENDED UP GETTING A CONCUSSION AND WHIPLASH AND WILL BE DOCTORING FOR A WHILE. THE PERSON AT BMW THAT WAS TAKING CARE OF THIS IS MICHAEL AND HIS PHONE NUMBER IS 201-571-5820. WE WERE TOLD BY AMERICAN FAMILY INSURANCE PERSON THAT GOING AFTER BMW TO GET THE REPORTS FROM THE TECHS WOULD BE VERY DIFFICULT. WE REALLY WOULD LIKE TO KNOW WHAT THE REPORTS SAY. I FEEL LIKE WE WERE GIVEN THE RUN AROUND. I WANT BMW TO ACKNOWLEDGE THAT THEY HAVE ISSUES WITH SUDDEN EXCELERATION. I AM VERY ANGRY ON HOW I WAS TREATED. THEY GAVE US NO INFORMATION AND WE WERE WITHOUT A CAR FOR 7 WEEKS. THE LAST WEEK THEY FINALLY GAVE US A RENTAL. PLEASE LOOK INTO THIS FOR ME.
HAD AN ACCIDENT ON A CITY STREET. VEHICLE WAS IN MOTION & IMPACT WAS ON THE FRONT BUMPER. ALL AIRBAGS DEPLOYED EXCEPT PASSENGER SIDE AIRBAG. VEHICLE HAD THE PASSENGER SIDE AIRBAG LAMP ILLUMINATED FOR A WHILE BEFORE THE ACCIDENT. CALLED DEALER AND BMW LONG BACK WHEN I INITIALLY CAME TO KNOW ABOUT THE RECALL. BUT I WAS TOLD THAT MY VIN IS NOT IN THE RECALL LIST. LUCKILY THERE WAS NO ONE IN THE PASSENGER SEAT WHEN THE ACCIDENT HAPPENED, ELSE WOULD HAVE BEEN WORSE. NHTSA CAMPAIGN NUMBER: 08V384000
MY 2006 3 SERIES BMW WAS INVOLVED IN A FRONTAL CRASH AND THE AIRBAGS FAILED TO DEPLOY AT A SPEED OF 30-35 PLUS WITH A FULL IMPACT. I HAVE SEVERE INJURIES IN THE SHOULDER AND NECK AREA AND HAVE BEEN HAVING BAD MIGRANE HEADACHES AND ALSO INSOMNIA. *TR
TL*THE CONTACT OWNS A 2006 BMW SI (NA). WHILE DRIVING APPROXIMATELY 5 MPH, THE DRIVER'S SIDE OF THE CONTACT'S VEHICLE WAS STRUCK. THE AIR BAGS FAILED TO DEPLOY. BOTH DRIVER'S SIDE DOORS WERE DAMAGED. THERE WERE NO WARNINGS PRIOR TO THE CRASH. THE VEHICLE WAS TOWED TO THE AUTHORIZED DEALER FOR REPAIRS. THE POLICE DEPARTMENT WAS CALLED TO THE SCENE AND A REPORT WAS FILED. AN OCCUPANT OF THE VEHICLE WAS INJURED. THE FAILURE AND CURRENT MILEAGES WERE 20,700.
WITHIN TWO MINUTES OF DRIVING, ON A CITY STREET, THE CAR WITH THE HEATED SEATS ON, I SMELLED A BURNING SMELL AND THOUGHT IT WAS COMING FROM ANOTHER CAR. BUT THE SMELL GOT STRONGER AND IT DIDN'T SMELL LIKE A CAR-RELATED SMELL. EVENTUALLY, THE SMELL GOT SO STRONG AND PUNGENT AND I SUDDENLY HAD A SHARP PAIN ON MY LEFT HIP AND I REALIZED IT THE HEATED SEAT WAS BURNING ME. THE PAIN WAS SO ACUTE I HAD TO LIFT MYSELF OFF OF THE SEAT, WHICH WAS DANGEROUS AND COULD'VE RESULTED IN AN ACCIDENT, AND I IMMEDIATELY PULLED OVER AND TURNED OFF THE HEATED SEATS. ONCE I TURNED THE HEATED SEAT OFF THE PAIN AND SMELL DISSIPATED. I GOT OUT OF THE CAR AND THERE WAS A CLEAR BURN HOLE BOTH ON THE SEAT AND ON MY PANTS. THE SMELL OF BURNT FABRIC LASTED IN THE CAR FOR SEVERAL DAYS AND FOR THE REST OF THE DAY I EXPERIENCED SHARP PAINS ON MY LEFT HIP AS IF IT WAS GETTING BURNED AGAIN.
HEATED SEAT MALFUNCTIONED WHEN TURNED ON THE SEAT GOT SO HOT IT BURNED THE BACK OF MY THIGH, STRONG SMELL OF SOMETHING BURNING. TURNED IT OFF RIGHT AWAY. I HAD JUST TURNED TH CAR ON IT HAPPENED WITHIN SECONDS OF TURNING THE HEATED SEAT BUTTON ON.
Presentadas por propietarios de este año del modelo y sin verificar por la NHTSA: el relato de una persona, no un hecho probado.
Water may come into contact with the starter relay and gradually cause corrosion. This could affect the electrical connection inside the relay and make the engine difficult to start. It may also result in a short circuit and could cause the starter to overheat leading to a fire when the vehicle is in motion or when it is parked with the ignition off. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Due to a manufacturing failure, the protection of the two outer headrests in the second row is reduced. In the event of a collision or accident, passengers could be injured. In addition, headrest parts may become exposed and also cause serious injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The RSW22 starter with reinforced water tightness (RWT) may experience increased abrasion of the magnetic contact, causing deposits to build up at the lowest point inside the relay. These deposits may increase relay contact resistance, leading to starting failures or short circuits. If a short circuit occurs, either when attempting to start the vehicle or while driving due to vibration-related movement of the deposits, it could cause a thermal event and increase the risk of fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Damaged brake discs may have been fitted to the front axle. This can lead the brakes to fail when a heavy load is placed on the wheel concerned, increasing the risk of accident and injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Failure to bolt the plus voltage (B+) cable tightly enough to the starter generator may result in contact problems and an increase in contact resistance at the bolted connection. This may in turn lead to local overheating and the vehicle catching fire or to the engine stalling while the vehicle is coasting. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The positive battery cable of the starter-generator may not have been manufactured correctly. This could result in a loose electrical connection, leading to excessive contact resistance. The vehicle cannot charge or start. Contact points in the starter-generator could overheat and cause a vehicle fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the inflator of the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments of the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The driver airbag inflator may malfunction due to long-term degradation. In this case, if the airbag is deployed in an accident, the internal pressure in the inflator may be too high. The inflator could burst. Metal fragments may cause injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The failure concerns the RSW22 starter, type RWT (reinforced for watertightness). Increased abrasion of the magnetic contact can lead to the formation of deposits at the lowest point of the relay interior. This in turn can increase the resistance of the relay contact, causing accidental ignition or even short circuits, possibly leading to a thermal reaction and fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The failure concerns the RSW22 starter, type RWT (reinforced for watertightness). Increased abrasion of the magnetic contact can lead to the formation of deposits at the lowest point of the relay interior. This in turn can increase the resistance of the relay contact, causing accidental ignition or even short circuits, possibly leading to a thermal reaction and fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The failure concerns the RSW22 starter, type RWT (reinforced for watertightness). Increased abrasion of the magnetic contact can lead to the formation of deposits at the lowest point of the relay interior. This in turn can increase the resistance of the relay contact, causing accidental ignition or even short circuits, possibly leading to a thermal reaction and fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The steering system sensor may malfunction causing an unintended steering movement of the vehicle. This increases the risk of accidents and injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The screw connection of the servo unit on the gear rack casing of the steering system may be faulty. This could cause the steering system to fail and become blocked, increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Due to faulty rear-most screws, the screw fixings of the boot's lashing rails can fail in the event of a rear-end collision with heavy intrusion and penetrate the backs of the rear seats. This increases the risk of injury to the occupants of the rear seats. The vehicles concerned have already been modified in connection with the recall code 0051960500. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant within the integrated inflator of driver airbags can deteriorate during time. If the airbag deploys, it could result in fragments from the inflator casing injuring the vehicle’s occupants. The product does not comply with the Regulation on the approval and market surveillance of Motor Vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Due to faulty rear-most screws, the screw fixings of the boot's lashing rails can fail in the event of a rear-end collision with heavy intrusion, and penetrate the backs of the rear seats. This increases the risk of injury to the occupants of the rear seats. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
A seam on the inflator housing of the driver airbag may not have been correctly welded. In case of accident, when the airbag is deployed, the inflator can burst, releasing metal parts which could cause injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The driver's airbag inflator propellant may deteriorate over time. If activated during an accident, excessive internal pressure may cause the inflator to burst, and metal fragments could pass through the cushion material causing injury to occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Due to a manufacturing error, the weld seam of the integrated transmission control unit (ITCU) may not have been correctly executed. As a result, transmission oil could leak into the ITCU, causing it to fail. This may lead to transmission seizure, increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Emparejadas por marca y nombre de modelo: Safety Gate no publica el VIN. Comprueba las fechas de fabricación y facilita el código de la llamada al concesionario.
BMW of North America, LLC (BMW) is recalling certain 2006-2010 BMW X3 2.5i, X3 3.0i and X3 xDrive30i Sports Activity Vehicles. The front passenger seat occupant detection mat that determines if, and how, the passenger frontal air bag should deploy in a crash may fatigue and develop cracks which could lead to a system failure.
Solución: BMW will notify owners, and dealers will replace the front passenger seat occupant detection mat, free of charge. Interim owner notification letters were mailed on November 27, 2017. A second notification letter will be sent when parts are available. Owners may contact BMW customer service at 1-800-525-7417.
BMW IS RECALLING 200,000 MY 2006 3 SERIES SPORT SEAT, MY 2004-2006 5 SERIES STANDARD AND SPORT SEAT, AND MY 2004-2006 X3 PASSENGER VEHICLES. DEPENDING ON THE MANNER AND FREQUENCY OF THE FRONT PASSENGER'S ENTRY AND EXIT, SMALL CRACKS HAVE DEVELOPED IN THE MAT. IF THIS OCCURS, THE FRONT PASSENGER AIR BAGS, WITH THE EXCEPTION OF THE HEAD PROTECTION SYSTEM, WILL BE DEACTIVATED AND THE AIR BAG WARNING LAMP AS WELL AS THE PASSENGER AIR BAG "ON-OFF" LAMP WILL BE ILLUMINATED.
Solución: DEALERS WILL REWORK THE FRONT PASSENGER SEAT SENSOR MAT SO THAT EXTERNAL FORCE APPLICATION TO THE SEAT DOES NOT CAUSE A CRACK TO THE MAT. THE RECALL BEGAN ON NOVEMBER 6, 2008. BMW WILL ALSO EXTEND THE WARRANTY ON THESE VEHICLES TO 10 YEARS FROM FIRST REGISTRATION WITHOUT ANY MILEAGE LIMIT. OWNERS MAY CONTACT BMW AT 1-800-525-7417.
Publicadas por año del modelo, no por VIN: pueden no afectar a este vehículo o ya estar resueltas. Confírmalo con un concesionario.