2009 BMW X6
10 recalls and 19 owner complaints on record for this model year.
Check a specific vehicle
This page describes the model. To see how one particular car is equipped, and whether its identifier is valid, decode its VIN.
Decode a VIN10 recalls and 19 owner complaints on record for this model year.
This page describes the model. To see how one particular car is equipped, and whether its identifier is valid, decode its VIN.
Decode a VINAlmost all of this describes the model year, not the individual car. Nothing here can tell you about this vehicle’s mileage, accidents or ownership — no identifier encodes those.
5 recalls carry a do-not-drive or park-outside warning. Check whether this vehicle was remedied before driving or storing it.
BMW of North America, LLC (BMW) is recalling certain 2008-2013 128i and 135i Convertibles, 128i, 135i, and M Coupes, 2007-2010 X3 30si and X3 xDrive30i, 2013-2015 X1 sDrive28i, X1 xDrive28i and X1 xDrive35i, 2007-2013 328i, 328i xDrive, 335i, 335is, 335i xDrive and M3 Coupes, 2006-2011 328i, 328xi, 328i xDrive, 325i, 325xi, 330i, 330xi, 335i, 335xi, 335i xDrive and M3, 2009-2011 335D, 2006-2012 325xi, 328i, 328xi and 328i xDrive, 2010-2011 X6 ActiveHybrid, 2007-2013 328i, 335i, 335is, M3 Coupes, X5 30si, X5 xDrive30i, X5 xDrive35i, X5 48i, X5 xDrive48i, X5 xDrive50i and X5 M, 2009-2013 X5 xDrive35d and 2008-2014 X6 xDrive35i, X6 xDrive50i and X6M vehicles equipped with non-desiccated driver frontal air bag inflators containing phase stabilized ammonium nitrate (PSAN) that were used as interim remedy parts for previous Takata recalls. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Remedy: BMW will notify owners, and dealers will replace the driver air bag. On X5 and X6 vehicles, only the inflator will be replaced. All repairs will be performed free of charge. The recall began March 11, 2020. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2009-2012 X5 xDrive35d, 2008-2012 X6 xDrive35i, X6 xDrive50i and X6 M, 2007-2012 X5 30si, X5 xDrive30i, X5 xDrive35i, X5 48i, X5 xDrive48i, X5 xDrive50i and X5 M and 2010-2011 X6 ActiveHybrid vehicles equipped with non-desiccated, passenger frontal air bag inflators containing phase stabilized ammonium nitrate (PSPI-2) propellant that were used as interim remedy parts for previous Takata recalls. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Remedy: Owners are advised not to drive their vehicles until this remedy is performed. BMW will notify owners, and dealers will replace the passenger front air bag, free of charge. The recall began March 11, 2020. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2007-2013 X5 xDrive30i, X5 xDrive35i, X5 xDrive48i, X5 xDrive50i and X5 M vehicles, 2008-2014 X6 xDrive35i, X6 xDrive50i and X6 M vehicles, 2009-2013 X5 xDrive35d vehicles and 2010-2011 X6 ActiveHybrid vehicles. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Remedy: Owners are advised not to drive their vehicles until the remedy is performed. BMW will notify owners, and dealers will replace the passenger frontal air bag module, free of charge. The recall began March 14, 2019. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2011-2012 BMW 550i, 550i xDrive, 550i Gran Turismo, 550i Gran Turismo xDrive, 750i, 750Li, 750i xDrive, 750Li xDrive, 760Li, X5 xDrive50i, X5 M, X6 xDrive50i, X6 M, ActiveHybrid7, MINI Cooper S Convertible, John Cooper Works (JCW) Convertible, Cooper S Countryman, Cooper S Countryman ALL4, Cooper S, JCW, Cooper S Clubman, JCW Clubman, Cooper S Roadster, JCW Roadster, Cooper S Coupe, JCW Coupe and Rolls-Royce Ghost, 2011 BMW X6 Hybrid and 2012 BMW 650i Coupe, 650i xDrive Coupe, 650i Convertible and 650i xDrive Convertible vehicles. The electric auxiliary water pump may fail and cause the circuit board to overheat.
Remedy: BMW will notify owners, and dealers will replace the electric auxiliary water pump, free of charge. Depending on the model, there are currently limited parts available, however not all parts are available at this time. Owners will be notified of the recall beginning June 11, 2018, and will receive a second notification when remedy parts become available. Owners may contact BMW customer service at BMW 1-800-525-7417, MINI at 1-866-825-1525, or Rolls-Royce at 1-877-877-3735. Note: BMW recommends that owners park their vehicle outdoors until the recall remedy has been performed.
BMW of North America, LLC (BMW) is recalling certain 2007-2013 X5 xDrive30i, X5 xDrive35i, X5 xDrive48i, X5 xDrive50i, X5 M, 2009-2010 X5 xDrive35d vehicles and 2009-2013 X6 xDrive35i, X6 xDrive50i, and X6 M vehicles ever registered in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." BMW is also recalling certain 2007-2010 X5 xDrive30i, X5 xDrive35i, X5 xDrive48i, X5 xDrive50i, X5 M, X5 xDrive35d, X6 xDrive35i, X6 xDrive50i and X6M vehicles ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." BMW is also recalling certain 2007-2009 X5 xDrive30i, X5 xdrive35i, X5 xDrive48i, X5 xDrive50i, X5 M, X5 xDrive35d, X6 xDrive35i, X6 xDrive50i and X6M vehicles ever registered in the states of AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY or "Zone C." These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Remedy: Owners are advised not to drive their vehicles until the remedy is performed. BMW will notify owners, and dealers will replace the passenger front air bag module, free of charge. The recall is expected to begin March 2018. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2012 X5 xDrive30i, X5 xDrive35i, X5 xDrive48i, X5 xDrive50i, X5 M, X6 xDrive35i, X6 xDrive50i, and X6 M vehicles originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, BMW is recalling certain 2009 X5 xDrive30i, X5 xDrive35i, X5 xDrive48i, X5 xDrive50i, and X5 M vehicles, 2008-2009 X6 xDrive 35i, X6 xDrive50i, X6 M, and 2009 X5 xDrive35d vehicles originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Additionally, unless included in "Zone A" or "Zone B" above, BMW is recalling certain 2007-2008 X5 xDrive30i, X5 xDrive35i, X5 xDrive48i, X5 xDrive50i and X5 M vehicles, and 2008 X6 xDrive35i, X6 xDrive50i, and X6 M vehicles originally sold, or ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to high absolute humidity and temperature cycling.
Remedy: Owners are advised not to drive their vehicles until the remedy is performed. BMW will notify owners, and dealers will replace the front passenger air bag inflator or air bag module, free of charge. Interim letters were mailed March 2017. Owners will receive a second notice when remedy parts become available. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain model year 2007-2011 BMW X5 3.0si, X5 4.8i, X5 M, X5 xDrive30i, X5 xDrive35i, X5 xDrive48i and X5 xDrive50i, 2008-2011 X6 x Drive35i, X6 xDrive50i and X6 M, 2010-2011 X6 ActiveHybrid, 535i xDrive Gran Turismo, 535i Gran Turismo, 550i xDrive Gran Turismo and 550i Gran Turismo, 2011-2012 528i, 535i, 535i xDrive, 550i and 550i xDrive and 2012 535i ActiveHybrid, 640i Convertible, 650i Convertible, 650i xDrive Convertible, 650i Coupe and 650i Coupe xDrive vehicles. The affected vehicles have in-tank fuel pumps that may have insufficiently crimped wire contacts.
Remedy: BMW will notify owners, and dealers will replace the fuel pump module, free of charge. The recall began February 2017. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain model year 2007-2011 X5 xDrive30i, X5 xDrive35i, X5 xDrive48i, X5 xDrive50i and X5M vehicles, 2009-2011 X5 xDrive35d vehicles, 2008-2011 X6 xDrive35i, X6 xDrive50i and X6 M vehicles, and 2010-2011 X6 ActiveHybrid vehicles originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, BMW is recalling certain model year 2007-2008 X5 xDrive30i, X5 xDrive35i, X5 xDrive48i, X5 xDrive50i and X5M vehicles, and 2008 BMW X6 xDrive35i, X6 xDrive50i and X6 M vehicles originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Vehicles of these model years and models that were not originally sold or ever registered in either Zones A or B are not subject to this safety recall. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to high absolute humidity and temperature cycling.
Remedy: Owners are advised not to drive their vehicles until they have been repaired. BMW will notify owners, and dealers will replace the passenger frontal air bag inflator or air bag module, free of charge. The recall began July 28, 2017. Owners may contact BMW customer service at 1-800-525-7417.
BMW IS RECALLING CERTAIN MODEL YEAR 2011 5-SERIES, MODEL YEAR 2010-2011 5-SERIES GRAN TURISMO, MODEL YEAR 2009-2011 7-SERIES, MODEL YEAR 2010-2011 X5 SAV, AND MODEL YEAR 2008-2011 X6 SAV VEHICLES EQUIPPED WITH 8- OR 12-CYLINDER, TURBOCHARGED, ENGINES BECAUSE THE CIRCUIT BOARD FOR THE ELECTRIC AUXILIARY WATER PUMP CAN OVERHEAT.
Remedy: BMW WILL NOTIFY OWNERS, AND DEALERS WILL REPLACE THE AUXILIARY WATER PUMP FREE OF CHARGE. THE SAFETY RECALL BEGAN ON DECEMBER 19, 2011. OWNERS MAY CONTACT BMW CUSTOMER RELATIONS AND SERVICES AT 1-800-525-7417.
BMW IS RECALLING MY 2009 X5 AND X6 VEHICLES. THE REAR BRAKE DISCS MAY NOT HAVE BEEN MANUFACTURED ACCORDING TO SPECIFICATIONS. AS A RESULT, A REDUCTION IN BRAKING PERFORMANCE AT THE AFFECTED REAR WHEEL COULD OCCUR.
Remedy: BMW WILL NOTIFY OWNERS AND WILL REPAIR THE VEHICLES BY INSPECTING THE REAR BRAKE DISCS AND, IF NECESSARY, REPLACE THEM FREE OF CHARGE. THE SAFETY RECALL BEGAN ON SEPTEMBER 11, 2009. OWNERS MAY CONTACT BMW CUSTOMER RELATIONS AND SERVICES TOLL-FREE AT 1-800-525-7417.
Published by model year, not by VIN — may not apply to this vehicle, or may already have been done. Confirm with a dealer.
Water may come into contact with the starter relay and gradually cause corrosion. This could affect the electrical connection inside the relay and make the engine difficult to start. It may also result in a short circuit and could cause the starter to overheat leading to a fire when the vehicle is in motion or when it is parked with the ignition off. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The engine starter’s electrical contacts may overheat and cause the vehicle to start improperly. Continued starting attempts can intensify the overheating and ignite surrounding components, potentially leading to a vehicle fire while driving or shortly after parking. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The RSW22 starter with reinforced water tightness (RWT) may experience increased abrasion of the magnetic contact, causing deposits to build up at the lowest point inside the relay. These deposits may increase relay contact resistance, leading to starting failures or short circuits. If a short circuit occurs, either when attempting to start the vehicle or while driving due to vibration-related movement of the deposits, it could cause a thermal event and increase the risk of fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The failure concerns the RSW22 starter, type RWT (reinforced for watertightness). Increased abrasion of the magnetic contact can lead to the formation of deposits at the lowest point of the relay interior. This in turn can increase the resistance of the relay contact, causing accidental ignition or even short circuits, possibly leading to a thermal reaction and fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The hollow shaft of the servomotor was not welded correctly. The weld may not be able to withstand high braking pressure build-up and may break. In this case, the reduced braking performance requires greater force and the braking distance may increase. In addition, the ABS and DSC brake control systems are not assisted. This increases the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The software-based overload protection function cannot sufficiently prevent the starter being overloaded in the event of repeated long start-up attempts. The starter may overheat or sparks may be produced as a result of an increased current flow. This increases the risk of a fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The gas generator in knee airbag modules was not properly inserted into the air cushion, resulting in the cushion failing to unfold sufficiently. As a result, it may not be able to deploy correctly in the event of an accident, leading to a reduction in the restraint effect, increasing the risk of injury to the occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The integrated braking system could be compromised, which could lead to an unexpected failure of the hydraulic braking assistance, thereby requiring greater pressure on the brake pedal. This can result in a longer braking distance, as well as failure of the Anti-lock Braking System (ABS) and the Dynamic Stability Control (DSC), increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The dashboard in the affected vehicles may not have been manufactured to the manufacturer specifications. In the event of anaccident, the passenger side airbag may not deploy as intended which could increase the risk of injury to the frontpassenger. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Due to a manufacturing error, the weld seam of the integrated transmission control unit (ITCU) may not have been correctly executed. As a result, transmission oil could leak into the ITCU, causing it to fail. This may lead to transmission seizure, increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Matched on brand and model name — Safety Gate publishes no VIN. Check the production dates, and quote the recall code to a dealer.
TL* THE CONTACT OWNS A 2009 BMW X6. WHILE DRIVING APPROXIMATELY 20 MPH, THE VEHICLE SUDDENLY STALLED AND SHUT OFF. THE VEHICLE WAS TOWED TO THE DEALER AND REPAIRED, BUT THE FAILURE CONTINUED. ALSO, WHILE DRIVING, FUEL FUMES AND SMOKE WERE PRESENT INSIDE THE VEHICLE. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE FAILURE MILEAGE WAS 70,000.
I WAS DRIVING HOME I LOST POWER IN MY ENGINE MY RADIATOR FAN WAS EXTREMELY HIGH THE GATE IS GOING UP AND DOWN WHEN THE CAR WAS COLD AND MY OBD GOT BURN OUT
I TOOK MY 2009 BMW X6 TO THE BMW DEALER, ADVANTAGE BMW MIDTOWN (HOUSTON, TEXAS) FOR SUSPECTED OIL LEAK AND EXCESSIVE WHITE SMOKE COMING FROM BOTH EXHAUST PIPES. I REQUESTED MULTI-POINT INSPECTION INCLUDING THE ENGINE. THE COMPLETE MULTI-POINT INSPECTION RESULTS ALONG WITH FINDINGS AND AN ESTIMATE CAN BE FOUND IN THE ATTACHED REPORT. WHICH INCLUDE: REPLACE VALVE SEALS, OIL RETURN COVER AND REAR MAIN SEAL (VALVE SEAL LEAKING AND MULTIPLE OIL LEAKS) REPLACE UPPER OIL PAN GASKET (UPPER OIL PAN GASKET LEAKING) REPLACE BULKHEAD COVERS (BULKHEAD COVERS COMING APART) REPLACE BOTH POST CAT O2 SENSORS (FAULTS STORED FOR POST-CAT O2 SENSORS) SPOKE WITH/COMMUNICATED WITH BMW SERVICE ADVISOR REP, BMW MIDTOWN (HOUSTON, TEXAS) REGARDING N63 ENGINE: VALVE SEAL REPLACEMENT " MANUFACTURER COMMUNICATIONS' LOCATED IN THE NHTSA WEBSITE: COMPONENTS: ENGINE NHTSA ID NUMBER: 10149960 MANUFACTURER COMMUNICATION NUMBER: B110815 MY CAR LISTESTED UNDER THIS CATAGOLRY AND ALL OTHER N63 ENGINE PROBLEMS (CASES). BMW SERVICE ADVISOR REP SAID ALREADY COMMUNICATE WITH BMW USA AND THE THEY TOLD HIM IM NOT QUALIFIED SINCE MY CAR IS 2009 OVER 10 OLD. NEXT MORNING, I CALLED BMW RECALL HOTLINE AT (800) 525-7417 AND THE EXCUTIVE OFFICES THEY TOLD ME THE SAME THING. MY CAR HAS 58243 MILES. THANK YOU
THE CAR WOULD SHAKE UNCONTROLLABLY AND WON'T ACCELERATE . IT STUTTERS AND READS REDUCE ENGINE POWER. THE CAR WAS IN MOTION AT THE TIME ON A CITY STREET. IT ALMOST STOPPED COMPLETELY. *TR
I TOOK MY 2009 BMW X6 TO THE BMW DEALER, UNION CITY GA FOR 3 PURPOSES: SUSPECTED LEAK OF COOLANT; CHECK ENGINE LIGHT ON; AND EXCESSIVE SMOKE COMING FROM BOTH EXHAUST PIPES. SPOKE WITH/COMMUNICATED VIA EMAIL WITH BMW SVC REP, WENT OVER DOCUMENTED CONCERNS...TO INCLUDE SMOKE FROM BOTH EXHAUST PIPES; RECEIVED DOCUMENT FOR APPROVAL; WHICH I APPROVED. RECEIVED VEHICLE 3 DAYS LATER, RETURNING HOME WITH VEHICLE TO OBSERVE SMOKE 'EXCESSIVE' FROM BOTH EXHAUST PIPES. RETURNED VEHICLE, TO BE TOLD BY SVC MGR, "I'M SORRY, I CAN ONLY REPRIMAND SVC REP, AS THE WORK THAT WAS DONE WOULD NOT CORRECT SMOKE FROM EXHAUST." THEN, SVC MGR WENT ON TO SPEAK OF THE CLASS ACTION LAW SUIT THAT ADDRESSED THIS PROBLEM, BUT THE TIMEFRAME TO HAVE THIS CORRECTED (FOR FREE) HAD EXPIRED 'BY DATE"...AND THIS INFORMATION IS USUALLY SENT TO THE ORIGINAL OWNER. AS I EXPRESSED TO HIM, I AM THE 4TH OWNER OF THIS VEHICLE AND RECEIVED NO INFORMATION...HE OF COURSE WAS APOLOGETIC AND GAVE AN ESTIMATE OF $8K TO CORRECT THIS PROBLEM (THAT I WAS "TOLD" AND PAID FOR WOULD CORRECT THE PROBLEM). I CALLED HQ BMW ONLY TO RECEIVE AN APOLOGY AND REFERRED TO BMW UNION CITY...TO RECEIVE A WRITTEN ESTIMATE FROM THE [SAME] SVC MANAGER. *SMOKE OBSERVED WIHILE VEHICLE IS STATIONARY WITH ENGINE ON; AND IN MOTION IN BOTH CITY AND ON HIGHWAY. BEGAN 3/16 - 3/31/2020
VANOS CAMSHAFT FAULT. FC 2A82 AND FC 2A87. I WAS DRIVING AT A SPEED OF 25MPH THE REDUCED ENGINE POWER LIGHT COMES ON. I STOP TURN THE CAR OFF AND RESTART IT THE LIGHT IS NOW OFF AFTER DRIVING FOR 10MINS THE LIGHT COMES BACK ON THERE IS A LOSS OF POWER I'M STEPPING ON THE GAS AND THE CAR IS NOT GOING THIS HAS HAPPENED NEARLY EACH TIME I'VE DRIVEN THE CAR LATELY. I TAKE THE CAR TO A SHOP SPENDING ALMOST $1000 TO TELL ME THE VANOS OR CAMSHAFT ITSELF IS THE PROBLEM THIS REPAIR IS CLOSE TO $4000. I SEE THAT THIS IS BINDER RECALL FOR 2010 TO 2014 MODELS I'M THINKING YOU JUST FORGOT US. HELP THANK YOU.
ENGINE IS LEAKING OIL AND IT'S A FIRE HAZARD... GOOGLE SEARCH FOR EXACTLY THE SAME ISSUE INDICATES THAT THIS IS A VERY COMMON WITH BMW. CAR HAS 25K MILES AND OIL FILTER GASKET AND CYLINDER HEAD ARE LEAKING OIL INTO ENGINE, THIS SHOULD NEVER HAPPEN ON A HARDLY DRIVEN CAR. SUSPECT BMW IS INTENTIONALLY USING DEFECTIVE PARTS TO CHARGE OUTRAGEOUS REPAIR FEES. OTHER MANUFACTURES RECALL THIS TYPE OF ISSUE, WHY IS BMW GETTING AWAY WITH THIS? SEE EXAMPLE YOUTUBE VIDEOS AT HTTPS://M.YOUTUBE.COM/WATCH?V=5CO92U-WA94 AND HTTPS://M.YOUTUBE.COM/WATCH?V=RYJLM5VEMMO
TL* THE CONTACT OWNS A 2009 BMW X6. THE CONTACT RECEIVED A RECALL NOTIFICATION FOR NHTSA CAMPAIGN NUMBER: 16V746000 (FUEL SYSTEM, GASOLINE). THE PART NEEDED WAS UNAVAILABLE TO PERFORM THE RECALL REPAIR. THE MANUFACTURER WAS NOT NOTIFIED OF THE ISSUE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. PARTS DISTRIBUTION DISCONNECT.
TL* THE CONTACT OWNS A 2009 BMW X6. THE CONTACT RECEIVED A RECALL NOTIFICATION FOR NHTSA CAMPAIGN NUMBER: 16V364000 (AIR BAGS); HOWEVER, THE PART TO DO THE REPAIR WAS UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE MANUFACTURER WAS MADE AWARE OF THE ISSUE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. VIN TOOL CONFIRMS PARTS NOT AVAILABLE.
TL* TAKATA RECALL. THE CONTACT OWNS A 2009 BMW X6. THE CONTACT RECEIVED A NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V071000 (AIR BAGS) HOWEVER, THE PART TO DO THE REPAIR WAS UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE MANUFACTURER WAS MADE AWARE OF THE ISSUE. THE CONTACT HAD NOT EXPERIENCED ANY FAILURES. VIN TOOL CONFIRMS PARTS NOT AVAILABLE.
TL* THE CONTACT OWNS A 2009 BMW X6. THE CONTACT STATED THAT THE FRONT DRIVER AND PASSENGER SIDE HEADLIGHT LENSES PREMATURELY DETERIORATED AND WERE CRACKED TO THE POINT THAT THE LENSES COULD FRACTURE. THE CONTACT STATED THAT A SOLUTION WAS MELTING THE SEALER. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 39,000. UPDATED 11/18/15*LJ CONTACT STATED THE HEADLIGHT LENSES CANNOT BE REPLACED. THE ENTIRE HEADLIGHT ASSEMBLY HAS TO BE REPLACED BOTH LEFT AND RIGHT THE COST IS $4,500.00 TO FIX. CONTACT'S CONCERN IS MOISTURE WILL GET IN THE HEAD LIGHTS AND CAUSE COMPLETE FAILURE AT NIGHT AND HAVE AN ACCIDENT. 4/13/18*JB *JB
TL* THE CONTACT OWNS A 2009 BMW X6. WHILE DRIVING AT APPROXIMATELY 60 MPH, THE HOT TEMPERATURE WARNING LIGHT ILLUMINATED AND THE ENGINE STALLED. THE VEHICLE HAD TO COOL DOWN IN ORDER FOR THE VEHICLE TO RESTART. THE FAILURE RECURRED TWICE. THE VEHICLE WAS REPAIRED. THE MANUFACTURER WAS NOT MADE AWARE OF THE FAILURE AND THE VIN WAS NOT INCLUDED IN NHTSA CAMPAIGN NUMBER: 11V521000 (ENGINE AND ENGINE COOLING). THE FAILURE MILEAGE WAS APPROXIMATELY 77,000. MA 07/30/2015
TL* THE CONTACT OWNS A 2009 BMW X6. THE CONTACT STATED THAT THERE WAS A NOISE COMING FROM THE FRONT OF THE VEHICLE. THE CONTACT ALSO MENTIONED THAT THE VEHICLE OVERHEATED SEVERAL TIMES. THE VEHICLE WAS TAKEN TO AN AUTHORIZED DEALER WHO REPLACED THE AUXILIARY WATER PUMP. THE FAILURE DID NOT RECUR. THE VEHICLE WAS NOT INCLUDED IN NHTSA CAMPAIGN NUMBER: 11V521000 (ENGINE AND ENGINE COOLING). THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 54,000.
WAS GOING TO LUNCH APPROX. 3-4 MILES FROM MY HOME AS I PULLED INTO THE PARKING LOT, THE COMPUTER GAVE A PANIC WARNING TO IMMEDIATELY TURN OFF THE ENGINE AS IT WAS OVERHEATING AND CAN CAUSE DAMAGE. I TURNED OFF THE MOTOR AND WAS CONFUSED AS THAT WAS THE ONLY WARNING AND IT APPEARED THAT NOTHING WAS WRONG. I GOT OUT OF THE CAR AND OPENED THE HOOD. AS I WAS DOING SO THE EXPANSION TANK EXPLODED AND THE HOT WATER SHOT PAST ME AND JUST CAUGHT MY RIGHT SHOULDER. NEEDLESS TO SAY IF THIS CAUGHT ME DEAD ON I WOULD HAVE BEEN BURNED BADLY. I CALLED THE DEALER AND WAS TOLD THAT THERE WAS NO RECALL ON MY VEHICLE. THE DEALER ALSO TOLD ME TO CALL ANOTHER DEALER AS THEY MAY HAVE BETTER INFORMATION. I HAD THE EXPANSION TANK REPLACED AND THEY REPLACED THE COOLANT. THERE SEEMS TO BE A AIR POCKET IN THE ENGINE AND THE COOLANT NEEDS TO BE TOPPED OFF AFTER RUNNING THE ENGINE. IF NO RECALL, WHY NOT? *TR
TL* THE CONTACT OWNS A 2009 BMW X6. THE CONTACT STATED THAT THE VEHICLE BECAME VERY UNSTABLE WHEN DRIVING OVER BUMPS. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS NOT NOTIFIED. THE VIN WAS UNAVAILABLE. THE FAILURE MILEAGE WAS 74,000.
Filed by owners of this model year and unverified by NHTSA — one person’s account, not an established fact.