2017 BMW M3
2 recalls and 3 owner complaints on record for this model year.
Check a specific vehicle
This page describes the model. To see how one particular car is equipped, and whether its identifier is valid, decode its VIN.
Decode a VIN2 recalls and 3 owner complaints on record for this model year.
This page describes the model. To see how one particular car is equipped, and whether its identifier is valid, decode its VIN.
Decode a VINAlmost all of this describes the model year, not the individual car. Nothing here can tell you about this vehicle’s mileage, accidents or ownership — no identifier encodes those.
BMW of North America, LLC (BMW) is recalling certain 2016-2017 BMW M3 Sedans, 2016-2017 BMW M4 and M4 GTS Coupes and 2017 BMW M4 Convertible vehicles. The connection between the driveshaft and the flange may fail resulting in a loss of propulsion.
Remedy: BMW will notify vehicle owners, and dealers will replace the driveshaft, free of charge. The recall began April 9, 2019. Owners may contact BMW customer service at 1-800-525-7417.
BMW North America, LLC (BMW) is recalling certain model year 2016 BMW M2 Coupe vehicles, 2015-2017 M3 Sedan vehicles and 2015-2016 M4 Coupe and M4 Convertible vehicles. During servicing of the rear differential for a prior service action, the rear sub-frame bolts may have been reused instead of being replaced. Reuse of the existing bolts may cause the bolts to loosen.
Remedy: BMW will notify owners, and dealers will replace the rear sub-frame bolts with new bolts, free of charge. The recall began on November 3, 2016. Owners may contact BMW customer service at 1-800-525-7417.
Published by model year, not by VIN — may not apply to this vehicle, or may already have been done. Confirm with a dealer.
The propellant in the inflator of the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments of the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The driver airbag inflator may malfunction due to long-term degradation. In this case, if the airbag is deployed in an accident, the internal pressure in the inflator may be too high. The inflator could burst. Metal fragments may cause injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The driver airbag inflator may malfunction due to long-term degradation. In this case, if the airbag is deployed in an accident, the internal pressure in the inflator may be too high. The inflator could burst. Metal fragments may cause injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The accumulator in the driver/passenger head airbag inflator can leak, preventing the airbag to fully deploy if activated in an accident, impairing the protective effect of the airbag. Moreover, the accumulator can detach, entering the interior of the vehicle or becoming detached from the vehicle. This can lead to an increased risk of injury for passengers and/or other road users. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Due to a manufacturing error, the weld seam of the integrated transmission control unit (ITCU) may not have been correctly executed. As a result, transmission oil could leak into the ITCU, causing it to fail. This may lead to transmission seizure, increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Matched on brand and model name — Safety Gate publishes no VIN. Check the production dates, and quote the recall code to a dealer.
My car was leaking fuel. This has been reported in numerous vehicles of the same make and model. There is an active warranty extension for this issue, I have attached the bulletin from BMW. My car is not covered for some reason although earlier years of my exact same car are covered. My car was was manufactured a few months after the latest covered date in the attached bulletin. This is a huge safety concern. There was always fuel dripping from my car. This resulted in puddles of fuel if my car was parked for longer than 30 mins. The slightest spark or someones cigarette could have lit up my entire vehicle in flames. Not only is it a safety concern, it should be an environmental concern as well. Everywhere I parked, fuel would be on the ground. Picture of my fuel tank attached. It is consistent with the issue in the bulletin. Photo is from the dealership that repaired my car.
The contact owns a 2017 BMW M3. The contact stated that while driving at approximately 25 MPH, there was an abnormal banging sound coming from the vehicle. In addition, the vehicle failed to operate as designed, without warning. The vehicle was towed to the dealer where it was diagnosed that the driveshaft was fractured and needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure. The VIN was not included in NHTSA Campaign Number: 18V713000 (Power Train). The approximate failure mileage was 53,000.
VEHICLE IS A 2017 BMW M3 WITH 6352 MILES. IN THIS PARTICULAR CASE THE VEHICLE HAD STARTED AND HAD BEEN OPERATING NORMALLY THE DAY PRIOR. THE FOLLOWING DAY THE CAR WAS STATIONARY AND WOULD NOT START.IT WAS CLEAR THERE WAS NO POWER GETTING TO THE ELECTRONICS EVEN THOUGH THE BATTERY WAS FULLY CHARGED. THE VEHICLE WAS TRANSPORTED BY FLATBED TRUCK TO THE LOCAL DEALERSHIP TO DIAGNOSE THE ISSUE. THE DEALERSHIP INVESTIGATED THE ROOT CAUSE AND FOUND THE PRIMARY BATTERY CABLE CONNECTOR TO THE ELECTRICAL DISTRIBUTION BOX HAD FAILED WHERE THERE WAS NO LONGER ELECTRICAL CONTACT BETWEEN THE CABLE END AND THE DISTRIBUTION BOX TERMINAL. THE DEALERSHIP HAD NOT INITIALLY DISCLOSED THAT THEY HAD DONE REPAIR WORK ON OTHER MODELS FOR THE SIMILAR TYPE ELECTRICAL FAILURE. UPON FURTHER RESEARCH IT WAS FOUND THAT THERE HAVE BEEN NUMEROUS RECALLS FOR MANY DIFFERENT MODELS OF BMW INCLUDING 1 SERIES, 3 SERIES AND Z SERIES FOR THE SIMILAR FAILURE MODE OF ELECTRICAL CONNECTION FAILURE AT THE BATTERY CABLE/ DISTRIBUTION BOX CONNECTION. THE FOLLOWING ARE SO FAR THE KNOWN RECALLS RELATED TO THE BATTERY CABLE CONNECTOR FAILURE: 18V-314 FOR MODEL YEARS 2010-2011. OVER 7000 VEHICLES AFFECTED 19V-472 FOR MODEL YEARS 2008-2012 13V-044 FOR MODEL YEARS 2008-2012 OVER 500,000 VEHICLES AFFECTED IT WAS EVENTUALLY CONFIRMED BY THE MECHANICS AT THE DEALERSHIP THAT THIS WAS A SIMILAR FAILURE MODE OF THE CONNECTOR THAT THEY HAD SEEN IN THE PAST HOWEVER THEY COMMENTED THAT THIS WAS THE FIRST 2017 MODEL THAT THEY HAD SEEN WITH THIS FAILURE. THE CONCLUSION CAN BE DRAWN ON THAT THE BATTERY CABLE/ELECTRICAL DISTRIBUTION BOX CONNECTOR DESIGN IS SIMILAR TO THAT USED IN PREVIOUS MODEL YEARS AND THEREFORE WILL FAIL IN A SIMILAR MANNER AND THAT ADDITIONAL MODEL YEARS SHOULD BE ADDED TO THE RECALL SO THAT THE DEFECT CAN BE IDENTIFIED AND REMEDIED AS SOON AS POSSIBLE.
Filed by owners of this model year and unverified by NHTSA — one person’s account, not an established fact.