6 Rückrufe und 70 Halterbeschwerden für dieses Modelljahr erfasst.
Diese Seite beschreibt das Modell. Um zu sehen, wie ein einzelnes Fahrzeug ausgestattet ist und ob seine Kennung gültig ist, entschlüsseln Sie die FIN.
FIN entschlüsselnFast alles hiervon beschreibt das Modelljahr, nicht das einzelne Fahrzeug. Nichts davon sagt etwas über Laufleistung, Unfälle oder Eigentum dieses Autos — keine Kennung kodiert das.
A deer was standing ahead in the road and I began to brake! I was only going 25-30mph. The brakes were hard to push and it felt like something was malfunctioning eventually hitting the deer straight on!!! The Automatic Braking System did NOT work, the forward collision warning did NOT work and the BRAKES did not work after pressing hard to brake to avoid a collision!!! I have had this BMW for over a year and have had several recalls that the dealership fixed EXCEPT for the IB recall issued on 2/12/24 that they still have NO REMEDY!!!!!!! Not only is this a MAJOR safety issue that I've expressed to them many times- the worst has happened now and my braking system FAILED causing a collision!!! The Phil Hughes service dept. has lied about filling my washer fluid and that the faulty battery issue was due to it sitting too long! I drive this car EVERY DAY!! They also did not even disclose to me that there were faulty sensor issues when I had it serviced recently!! I do NOT trust them at this point!! Just this past week my check engine light went off and on. My husband unscrewed and screwed on the gas cap - the light was still on and then just went off as I was driving the next day! My battery still goes completely dead for unknown reasons....... I DO NOT FEEL SAFE!!! I am disabled from being rear-ended from a tractor trailer 4 years ago and this car has completely TRAUMATIZED me all over again and I will not drive this BMW ever again!!
The vehicle is equipped with a dual clutch transmission and has the EPA mandated auto-start feature. When you stop the vehicle and the engine shuts off and then remove your foot from the brake to go forward, the engine hesitates to restart and then starts, revs, dumps the clutch and propels you forward at a dangerous rate. My wife was trying to pull into the garage and stopped a little short. When she tried to move forward about a foot, the car started and lurched forward hitting the house. There is no way to disable the auto start feature and there are no buttons in the car. This is going to get someone killed when they are trying to make a left turn across traffic and first the car doesn't restart and then it starts and flies into traffic. I complained to BMW and they say this is the way the government mandates the car to be.
In November 2025, I was driving an errand on city streets in a neighborhood. Speed was approximately 30-35MPH. Two lane road. There were no hazards in the road and while I was descending down a hill, my forward collision/emergency braking system activating, causing my vehicle to come to a complete and full stop from road speed. This had happened several other times when reversing out of parking spots into traffic or driving position but since the speed was slow and I do have cross traffic/collision avoidance, I initially I assume it was related to surrounding vegetation and sensor sensitivity. The issue happened again in December 2025 but I was moving at a much slower pace. In May 2025, I had the BMW integrated braking system recall addressed (NHTS #24V1040034860200). However, per the NHTSAA website, it appears there was a subsequent recall/safety repair required for the exact same issue, NHTS Recall #24V739000. I was not aware of this; was not notified by the dealership nor BMW and it could correlate to this issue. On June 4, 2026, I took my BMW to the BMW of El Cajon dealership in order to investigate the issue, as well as to address a nail in a tire and a brake warning light. Prior to attending the appointment, I noted the second recall for the braking system. However, the dealership is not checking or simply stating that there is no open recall on my vehicle which does not correlate with the NHTSA website. I am pushing this issue up the administrative chain of command but am very concerned. The dealership is simply attempting to replicate the issue without further investigation and refused to check the computer system nor the equipment replaced in May 2025 to confirm that there are no mechanical/system failures. Had this issue occurred on a freeway, I would have been in HUGE danger. I request that the NHTSA look into BMW and, specifically, this dealerships handling of mandatory safety recalls.
am writing to report a potential safety and fire hazard issue involving my BMW X1, along with ongoing electrical concerns I have experienced with this vehicle since purchase. Approximately two weeks ago, for the first time in three years, I needed to bring the vehicle in for an oil change. Due to my work commute of more than two hours each way, neither the BMW dealership near my home nor the one near my workplace was able to accommodate me within a reasonable timeframe. Because I could not continue driving without service, I brought the vehicle to Jiffy Lube for an oil change. During the visit, I agreed to replace the cabin/carbon air filter as recommended. Approximately three weeks later, while driving, I turned on the air conditioning and immediately noticed a strong burning smell coming from the vents. Concerned about a possible electrical or overheating issue, I turned the air off immediately. I contacted BMW service and the earliest available appointment was scheduled for May 20, 2026. During the scheduling call, the BMW service representative informed me that my vehicle also had an active recall that would be addressed during my appointment. When I asked for details, I was told it involved a “software update issue.” On May 18, 2026, I attempted to use the air conditioning again. This time, the burning smell became significantly worse and was combined with a musty odor. Shortly afterward, the ventilation system stopped blowing air entirely. When I arrived at BMW service, I explained the symptoms to my advisor. He responded that the issue “sounded familiar” and stepped away to speak with someone else. When he returned, he explained that another customer had recently reported a similar issue involving a recall on a BMW M5, but stated that the BMW X1 did not currently have the same recall. Given the burning odor, ventilation failure, and the similarity to another BMW recall-related complaint, I believe this issue should be investigated further as a potential hazar
Right around mid-December 2025, I parked my car, and went to bed, just to wake up on a notification that my battery was depleted and I should go to a service center. I went to the nearest BMW dealership, and had them check out the issue. They said it was caused by 2 incidents where I the car's engine was off with key on for 9 minutes and 10 minutes respectively. and therefore it is my fault and the battery is damaged. So, they had to replace it, and they charged me $1,100 for it. I still don't see how that's my fault, because when I put the car in parking and not exit, the engine turns itself off anyways, but entertainment stays on.
1 Brakes: The brakes seem to have excessive wear. The car was purchased new and started making loud squeaking noises after about 18k miles. The squeaking sometimes went away after regular maintenance, but usually reappeared withing a few hundred miles of driving. Two different BMW dealership service centers examined the car at different times and claimed the squeaking was a sensor, however there was never a dashboard light or computerized message stating the same. At about 29K, a dashboard light and computerized message displayed warning the brakes needed regular maintenance. Strangely, the loud squeaking went away as soon as the dashboard light displayed. 2 Lane Keeping Assistance: the car will attempt to swerve into other lanes, fighting my attempts to control the steering wheel. This happens when lane markings have been redrawn, but the vehicle is detecting the painted-over lines and tries to divert to there instead. It also happens when a lane has an option to split into different directions. If I am driving straight, the vehicle will try to swerve into the alternate direction, instead of proceeding in the direction the car is already traveling. This sometimes risks driving into a curbs or barriers that separate the directions and has occurred numerous times.
The Rear Cross Traffic system does not work! A few days ago a car stopped inches away from me without any warning. I was backing out of a parking space at the grocery store.
Dealer says the needed parts are on back order. It has been over 1 year, and I have been unable to get the needed repairs.
The contact owns a 2023 BMW X1. The contact received notification of NHTSA Campaign Number: 24V104000 (ELECTRONIC STABILITY CONTROL (ESC), SERVICE BRAKES, HYDRAULIC); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact stated while driving at various speeds and attempting to slow down, the brake pedal was depressed; however, there was a slight resistance while depressing the brake pedal. There was no warning light illuminated. The vehicle was not repaired. The manufacturer was not made aware of the failure. The approximate failure mileage was 1,000. VIN tool confirms parts not available.
The contact owns a 2023 BMW X1 equipped with Bridgestone Tires, Tire Line: Turanza, Tire Size: 225/55/R18, DOT Numbers: 16C1005HC0723 (Rear Tires) and 16C1005HC0823 (Front Tires). The contact stated that upon taking the vehicle for service, the contact was informed that all 4 tires needed to be replaced. The contact was informed that the front tires had 1-millimeter of treadwear remaining, and the rear tires had 3-millimeter of treadwear remaining. The vehicle was taken to the dealer, who was unable to determine the cause of the abnormal treadwear. The vehicle was not repaired. The manufacturer was notified of the failure, a case was opened, and the contact was referred to the NHTSA Hotline for assistance. The failure mileage was 7,000.
The contact owns a 2023 BMW X1. The contact received notification of NHTSA Campaign Number: 24V104000 (Electronic Stability Control (ESC), Service Brakes, Hydraulic); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.
I received notice on the recall for my vehicle in October 2024. Since then I have tried to make appointments with BMW of Ramsey to fix the recall issue and they have told me each time that the part is not available and they cannot fix the issue. We are now in May 2025 and this has not been attended to.
The contact owns a 2023 BMW X1. The contact received notification of NHTSA Campaign Number: 24V104000 (Electronic Stability Control (ESC), Service Brakes, Hydraulic); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.
The contact owns a 2023 BMW X1. The contact received notification of NHTSA Campaign Number: 24V104000 (Electronic Stability Control (ESC), Service Brakes, Hydraulic); however, the part to do the recall repair was not yet available. The local dealer was contacted and confirmed that parts were not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.
The contact owns a 2023 BMW X1. The contact received notification of NHTSA Campaign Number: 24V104000 (ELECTRONIC STABILITY CONTROL (ESC), SERVICE BRAKES, HYDRAULIC); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available .
Von Haltern dieses Modelljahrs eingereicht und von der NHTSA nicht geprüft — die Schilderung einer Person, keine feststehende Tatsache.
BMW of North America, LLC (BMW) is recalling certain 2025 Mini Cooper S, Mini Countryman S All4, X2, 2024 Rolls-Royce Spectre, 2023-2025 i7, 7 Series, X7, 2024-2025 i5, 5 Series, 2023-2024 XM, X1, 2024-2025 X6, and X5 vehicles. The integrated brake (IB) system may malfunction and result in a loss of power brake assist or cause the Antilock Brake (ABS) and Dynamic Stability Control (DSC) systems to not function properly.
Abhilfe: The Integrated brake system will be inspected and, if necessary, replaced, free of charge. Owner notification letters are expected to be mailed August 21, 2026. Owners may contact BMW customer service at 1-800-525-7417 or Rolls-Royce customer service at 1-877-877-3735. Vehicle Identification Numbers (VINs) involved in this recall will become searchable on NHTSA.gov beginning August 21, 2026. Vehicles previously repaired under recall 24V739 or 24V104 will need to have the new remedy completed.
BMW of North America, LLC. (BMW) is recalling certain 2023-2024 X1, X5, X6, X7, XM, 530i, i5, 740i, 760i, i7, and 750e vehicles. Please see the recall report for a complete list of models and model years. The integrated brake (IB) system may malfunction and result in a loss of power brake assist or cause the Antilock Brake (ABS) and Dynamic Stability Control (DSC) systems to not function properly.
Abhilfe: Dealers will replace the integrated brake module, free of charge. Interim owner notification letters notifying owners of the safety risk are expected to be mailed November 22, 2024. Second letters will be mailed once the parts are available. Owners may contact BMW customer service at 1-800-525-7417. Vehicles in this recall were previously repaired under recall number 24V-104 and will need to have the new remedy completed.
BMW of North America (BMW) is recalling certain 2023-2024 X1, 2024-2025 X5, 2025 X6, 2023-2025 X7, 740i, 760i, 2024 XM, 530i, 540i, i7, 750e, X2, 2024-2025 i5, 2024 Rolls Royce Spectre, 2025 MINI Countryman S ALL4, JCW Countryman ALL4, and 2025 MINI Hardtop 2 Door (Cooper, Cooper S) vehicles. Please refer to the recall report for the complete list of models. The welds in the servomotor of the integrated brake control module may break, causing a loss of power brake assist and rear brake function. In addition, the Antilock Brake System (ABS) and Dynamic Stability Control (DSC) system may not function.
Abhilfe: Dealers will replace the integrated brake system, free of charge. Owner notification letters were mailed November 13, 2024. Owners can contact BMW Customer Service at 1-800-525-7417.
BMW of North America, LLC. (BMW) is recalling certain 2023-2025 BMW, MINI, and Rolls-Royce vehicles. Please see the recall report for a complete list of models and model years. The integrated brake (IB) system may malfunction and result in a loss of power brake assist or cause the Antilock Brake (ABS) and Dynamic Stability Control (DSC) systems to not function properly.
Abhilfe: Dealers will replace the integrated brake system, free of charge. Owner notification letters were mailed between June and December 2024. Owners may contact BMW customer service at 1-800-525-7417 or Rolls Royce customer service at 1-877-877-3735.
BMW of North America, LLC (BMW) is recalling certain 2023 X1 xDrive28i, X1 M35i vehicles. On the second-row outboard seats, the seat belts may have been pinched by an interior trim panel during vehicle assembly.
Abhilfe: Dealers will inspect and adjust the interior trim panel, as necessary, free of charge. Owner notification letters were mailed June 9, 2023. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2022-2023 iX xDrive40, iX xDrive50, iX M60 and 2022-2023 X1 xDrive28i vehicles. The front driver's air bag may have been manufactured incorrectly and may not deploy as intended during a crash.
Abhilfe: Dealers will replace the driver's air bag, free of charge. Owner notification letters were mailed April 14, 2023. Owners may contact BMW customer service at 1-800-525-7417.
Nach Modelljahr veröffentlicht, nicht nach FIN — betrifft dieses Fahrzeug möglicherweise nicht oder wurde bereits erledigt. Beim Händler bestätigen.
The seatbelts in the second row may not have been manufactured correctly and could cause the car-sensitivity sensors to fail. This could reduce the protective effect of the seatbelts and lead to injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The seat belts of the car were not manufactured correctly. In the event of a collision or accident, the restraint function of the seat belts may be reduced and may not provide the necessary protection. As a result, there may be an increased risk of injury. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The cell modules in the vehicles concerned were not produced in accordance with the specifications, which may cause the module frame to fail. This may lead to a shutdown of the high-voltage system and fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The material used for the B-pillar reinforcement plates is inadequate. This can alter the crash characteristics, leading to an increased risk of injuries in the event of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the inflator of the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments of the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The driver airbag inflator may malfunction due to long-term degradation. In this case, if the airbag is deployed in an accident, the internal pressure in the inflator may be too high. The inflator could burst. Metal fragments may cause injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The hollow shaft of the servomotor was not welded correctly. The weld may not be able to withstand high braking pressure build-up and may break. In this case, the reduced braking performance requires greater force and the braking distance may increase. In addition, the ABS and DSC brake control systems are not assisted. This increases the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant within the integrated inflator of driver airbags can deteriorate during time. If the airbag deploys, it could result in fragments from the inflator casing injuring the vehicle’s occupants. The product does not comply with the Regulation on the approval and market surveillance of Motor Vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The front left seat's height adjustment mechanism may have been incorrectly riveted, potentially compromising the seat's structural integrity. In an accident, this could have a negative impact on the restraint system and increase the risk of injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The seat recliner adjuster may not be correctly welded, which could cause the backrest not to lock. If it doesn't lock, the seatback might not stay secure in a collision, increasing the risk of injury. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The integrated braking system could be compromised, which could lead to an unexpected failure of the hydraulic braking assistance, thereby requiring greater pressure on the brake pedal. This can result in a longer braking distance, as well as failure of the Anti-lock Braking System (ABS) and the Dynamic Stability Control (DSC), increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Abgeglichen über Marke und Modellname — Safety Gate veröffentlicht keine FIN. Prüfen Sie die Produktionsdaten und nennen Sie dem Händler den Rückrufcode.