2019 BMW X7
11 recalls and 47 owner complaints on record for this model year.
Check a specific vehicle
This page describes the model. To see how one particular car is equipped, and whether its identifier is valid, decode its VIN.
Decode a VIN11 recalls and 47 owner complaints on record for this model year.
This page describes the model. To see how one particular car is equipped, and whether its identifier is valid, decode its VIN.
Decode a VINAlmost all of this describes the model year, not the individual car. Nothing here can tell you about this vehicle’s mileage, accidents or ownership — no identifier encodes those.
BMW of North America, LLC (BMW) is recalling certain 2020 340I, X6, 2020-2025 840I, 2020-2022 740LI, 2019-2020 X7, and X5 vehicles. After repeated attempts, the starter motor may overheat from an electrical overload.
Remedy: Dealers will replace the engine starter, free of charge. This recall includes vehicles repaired under recall 24V576 and those owners will need to have their vehicle repaired again. Owner notification letters were mailed February 9, 2026. Owners may contact BMW customer service at 1-800-525-7417. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov November 17, 2025.
BMW of North America, LLC is recalling certain 2019-2020 X5, X7, 2020 3 Series Sedan, X6, 2020-2021 7 Series Sedan, 2020 8 Series Convertible, 8 Series Coupe, and 2020 8 Series Gran Coupe vehicles. Please see the recall report for the complete list of models. In the event the starter motor fails, repeated attempts to start the vehicle can cause the starter motor to overheat from an electrical overload.
Remedy: Dealers will update the vehicle software, free of charge. Owner notification letters were mailed September 27, 2024. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2019-2022 BMW X7 xDrive40i, X7 Drive50i, X7 M50i vehicles with third-row seats. One or more of the compression springs that lock the backrest may not have been installed properly, and could dislodge or detach.
Remedy: Dealers will inspect the third-row seat and, if necessary, remove and reinstall improperly installed compression springs, and reinstall any missing springs, free of charge. Owner notification letters were mailed November 4, 2022. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2022 4 Series Gran Coupe (430i, 430i xDrive, M440i xDrive); 2019-2022 X5 sDrive40i, X5 xDrive40i, X5 xDrive50i, X5 M50i, X5M; 2021-2022 X5 xdrive45e; 2020-2022 X6 sDrive40i, X6 xDrive40i, X6 xDrive50i, X6M and 2019-2023 X7 xDrive40i, X7 xDrive50i, X7 M50i, X7 xDrive60i, X7 M60i, X7M, Alpina XB7 vehicles. The roof function control unit may be programmed incorrectly, allowing the sunroof to close without the key fob present inside the vehicle. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 118, "Power-Operated Window Systems."
Remedy: Dealers will reprogram the roof function control unit, free of charge. Owner notification letters were mailed June 20, 2022. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2019-2021 X3 sDrive30i, X3 xDrive30i, X3 M40i, X3M, X4 xDrive30i, X4 M40i, M550i, X4M, X5 sDrive40i, X5 xDrive40i, X5 xDrive50i, X5M, X5 M50i, X7 xDrive40i, X7 xDrive50i, X7 M50i, Alpina XB7, 330i, 330i xDrive, M340i, M340i xDrive, and 8 Series Coupe, Convertible and Grand Coupe, 840i, 840i xDrive, M850i xDrive, M8, 2020-2021 530e, 530e xDrive, 330e, 330e xDrive, 745Le, 745Le xDrive, X5 xDrive45e, X3 xDrive30e, X6 sDrive40i, X6 xDrive40i, X6 xDrive50i, X6 M50i, X6M, 530i, 530i xDrive, 540i, 540i xDrive, M550i xDrive, M5, 740i, 740Li, 740Li xDrive, M760i Drive, M760Li xDrive, 750Li xDrive Alpina, Alpina B7 xDrive, and 2021 4 Series Coupe 430i, 430i xDrive, M440i xDrive vehicles. When shifting into Reverse, a small portion of the rearview image may be obscured, or the screen may not illuminate. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 111, "Rear Visibility."
Remedy: BMW will notify owners, and dealers will inspect the rearview camera software and update it if necessary, free of charge. The recall began April 16, 2021. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2020-2021 8 Series Coupe, Grand Coupe and convertible 840i, 840i xDrive, M850i xDrive, M8 and 740 Li, 740 Li xDrive, 750 Li xDrive, M760 Li xDrive, X6 sDrive40i, X6 xDrive40i, X6 xdrive50i, X6 M50i, X6M, and 2019-2021 X5 sDrive40i, X5 xDrive40i, X5 xDrive50i, X5 M50i, X5M, X7 xDrive40i, X7 xDrive50i, X7 M50i, and 2021 M3, M3 Competition, M4 Coupe, M4 Competition Coupe, X5 xDrive45e, 745 Le xDrive. The rotor and shaft within the integrated brake system may not have been welded properly and could separate during a hard braking event, possibly resulting in a loss of the Antilock Brake System (ABS) and braking assistance.
Remedy: BMW will notify owners, and dealers will replace the integrated brake system, free of charge. Owner notification letters were mailed on May 25, 2021. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2018 540d, 2018-2020 530i, 530i xDrive, 540i, 540i xDrive, M550i xDrive, M5, 530e, 530e xDrive, X3 sDrive, X3 xDrive, X3 M40i, X3 M, and 2019-2020 X4 xDrive, X4 M40i, X4 M, X7 xDrive, X7 M50i, 740Li, 740Li xDrive, 750Li, 750Li xDrive, 8 Series Convertible and Coupe 840i, 840i xDrive, M850i xDrive, X5 sDrive, X5 xDrive, X5 M50i, X6 xDrive, X6 M50i, 330i, 330i xDrive, M340i, M340i xDrive, Z4 sDrive, Z4 M40i, 740Le xDrive and 745Le xDrive, 2018-2019 640i xDrive Gran Turismo and Rolls-Royce Phantom, 2019 M850i xDrive Gran Coupe and Rolls-Royce Cullinan and 2020 Toyota Supra vehicles. The back-up camera and display settings can be adjusted such that the rear view image is no longer visible and the system will retain that setting the next time the vehicle is placed in reverse. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 111, "Rearview Mirrors."
Remedy: BMW will notify owners, and dealers will update the back-up camera software, free of charge. The recall began November 8, 2019. Owners may contact BMW customer service at 1-800-525-7417 or Rolls-Royce at 1-877-877-3735. Toyota owners may contact Toyota customer service at 1-888-270-9371.
BMW of North America, LLC (BMW) is recalling certain 2019 X5 xDrive50i and X7 xDrive40i vehicles. The left side wheel bolts may have been insufficiently tightened and may loosen over time.
Remedy: BMW will notify owners, and dealers will replace and tighten the left side wheel bolts, free of charge. The recall began July 16, 2019. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2020 750i xDrive, 2019 M850i xDrive Coupe, M850i xDrive Convertible, X5 xDrive50i, X7 xDrive50i, and M5 vehicles. The high pressure fuel pump may not have been properly attached to the engine, which may cause the fuel pump flange to crack, resulting in a fuel leak.
Remedy: BMW will notify owners, and dealers will replace the high pressure fuel pumps, free of charge. The recall began August 27, 2019. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2019 X7 xDrive40i and X7 xDrive50i vehicles. The driver and passenger head air bags may not have been properly aligned with the trim during installation.
Remedy: BMW will notify owners, and dealers will inspect and, as necessary, reinstall the head air bags, free of charge. The recall began July 18, 2019. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC is recalling certain 2019 BMW X7 xDrive40i and X7 xDrive50i vehicles equipped with the "business lounge seat" option. The attachment bolts between the seat adapter and the vehicle may not have been properly tightened.
Remedy: None of the affected vehicles have been sold and are quarantined on dealer lots. BMW dealers will replace the attachment bolts for the seat adapter, free of charge. The recall began on February 27, 2019. Owners may contact BMW's customer service at 1-800-525-7417.
Published by model year, not by VIN — may not apply to this vehicle, or may already have been done. Confirm with a dealer.
Water may come into contact with the starter relay and gradually cause corrosion. This could affect the electrical connection inside the relay and make the engine difficult to start. It may also result in a short circuit and could cause the starter to overheat leading to a fire when the vehicle is in motion or when it is parked with the ignition off. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The engine starter’s electrical contacts may overheat and cause the vehicle to start improperly. Continued starting attempts can intensify the overheating and ignite surrounding components, potentially leading to a vehicle fire while driving or shortly after parking. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The hollow shaft of the servomotor was not welded correctly. The weld may not be able to withstand high braking pressure build-up and may break. In this case, the reduced braking performance requires greater force and the braking distance may increase. In addition, the ABS and DSC brake control systems are not assisted. This increases the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The software-based overload protection function cannot sufficiently prevent the starter being overloaded in the event of repeated long start-up attempts. The starter may overheat or sparks may be produced as a result of an increased current flow. This increases the risk of a fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The gas generator in knee airbag modules was not properly inserted into the air cushion, resulting in the cushion failing to unfold sufficiently. As a result, it may not be able to deploy correctly in the event of an accident, leading to a reduction in the restraint effect, increasing the risk of injury to the occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The integrated braking system could be compromised, which could lead to an unexpected failure of the hydraulic braking assistance, thereby requiring greater pressure on the brake pedal. This can result in a longer braking distance, as well as failure of the Anti-lock Braking System (ABS) and the Dynamic Stability Control (DSC), increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The dashboard in the affected vehicles may not have been manufactured to the manufacturer specifications. In the event of anaccident, the passenger side airbag may not deploy as intended which could increase the risk of injury to the frontpassenger. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Matched on brand and model name — Safety Gate publishes no VIN. Check the production dates, and quote the recall code to a dealer.
ON DECEMBER 21ST 2019, THE BREAKS ON OUR BRAND NEW 2019 X7 BMW COMPLETELY GAVE OUT WHILE MY HUSBAND AND I AND THREE MINOR CHILDREN WERE TRAVELING ABOUT 70 MPH ON NY INTERSTATE 87. ALL THE LIGHTS STARTED BLINKING INSIDE THE VEHICLE AND IT KEPT DRIVING COMPLETELY WITHOUT OUR ABILITY TO STOP IT. SINCE THAT DATE, FOR OVER 40+ DAYS THE CAR HAS BEEN WITH BMW FOR REPAIR WITH NO COMMUNICATION FROM CORPORATE ON THE CAUSE JUST A CONFIRMATION THAT THE BRAKES INDEED WENT OUT. IT IS UNCLEAR WHETHER THIS IS A ONE-OFF ISSUE OR AN ISSUE WITH A FLEET OF THEIR CARS, BMW IS REFUSING ANY TRANSPARENCY INTO THE ISSUE.
This happened on my vehicle. Oil pump is supposed to last life of the vehicle per BMW. This left me stranded on the side of the road for hours and now is costing $9k to replace oil pump. My car has less than 100k miles. I'm reporting a safety issue with BMW vehicles equipped with the B58TU engine, primarily 2019-2021 models. These vehicles have an oil pump with an internal plastic component that regulates oil pressure, and this part is fracturing in the field, causing sudden loss of oil pressure. The failure typically occurs during cold starts in low temperatures. When it fails, oil pressure becomes erratic or is lost entirely, often with little to no warning before engine damage or vehicle disablement. Warning signs, when present, include inability to measure oil level electronically, abnormal oil pressure, or sudden drivetrain malfunction warnings. These can rapidly progress to engine shutdown or severe damage from oil starvation. This creates a dangerous situation because the vehicle can become disabled without warning while driving or after startup. This is especially hazardous when cars become immobilized in traffic or during winter conditions when failures occur most frequently, leaving occupants exposed to freezing temperatures while awaiting assistance. Pump replacement requires extensive disassembly and commonly costs $6,000-$8,000, assuming no engine damage. A critical concern: owners cannot determine if their vehicle has the original plastic pump or the later metal revision. BMW's VIN-based parts lookup now shows updated components even when original plastic parts remain installed, and BMW has removed the original plastic part number from dealer networks entirely. Failures are reported across multiple production years, and the scope of affected vehicles remains unclear. Because this condition causes sudden vehicle disablement without adequate warning, especially in cold weather, I believe this warrants investigation as a potential safety-related defect.
I am reporting a safety concern involving BMW vehicles equipped with the B58 Technical Update (B58TU) engine, commonly found in model years 2019–2021. These vehicles utilize a variable-displacement engine oil pump containing an internal thermoplastic adjusting component responsible for regulating oil pressure. Field failures are increasingly being reported in which this internal component fractures, resulting in sudden loss or instability of engine oil pressure/lubrication. Loss of lubrication can cause the vehicle to become disabled without warning while driving or shortly after startup. This creates a safety hazard, particularly when vehicles become immobilized in active traffic or during winter conditions the cold is when they fail the most, where occupants may be exposed to freezing temperatures while awaiting assistance. Owners are currently unable to determine whether their vehicles contain the original thermoplastic oil pump design or a later revised version utilizing metal internal components, as VIN-based parts information now identifies updated components in the car even when no replacement has occurred and the old components are actually in the car. Also, BMW has actively removed the plastic part number out of all dealer networks, demonstrating knowledge of the defective component.
The contact owns a 2019 BMW X7. The contact stated that the Auto START/STOP feature failed to function as intended. There was a fire message displayed. The vehicle was taken to the local dealer, where it was diagnosed; however, the dealer was unable to update the control unit. The control unit was not communicating as intended. The vehicle was not repaired. The contact received notification of NHTSA Campaign Number: 24V576000 (Electrical System, Engine, and Engine Cooling). The manufacturer was contacted, but no assistance was provided. The failure mileage was approximately 134,000.
I was told today that my BMW engine oil pump is failing because of plastic internal components which will cause irreversible catastrophic engine damage during operation which is extremely dangerous and that I was informed by the dealer that BMW quietly changed them 2 years after due to the failure rate. If the oil pump shatters, debris can permanently damage the engine during operation jeopardizing my safety and those driving around me, making replacement with the upgraded, all-metal oil pump, that BMW quietly changed due to this failure, nearly $6k -$8k to fix and is not covered though they admit it is a known failure/safety issue. As of XXX, BMW Korea is running a free repair campaign (recall) to address oil pump failures affecting the B58TU engine in that country. Affected vehicles include models manufactured between XXX and XXX. BMW Korea replaces the non-safe original plastic oil pump with BMW's upgraded metal design, and even covers prior out-of-pocket replacements. NHTSA needs to hold BMW accountable and force BMW USA to complete the same safety recall for the exact same issue of faulty engine oil pumps they installed to save money as BMW Korea for the United States. Safety recalls should NOT be optional in USA and especially so if BMW is already doing the recall in another country for same issue identified in their cars sold here in the [XXX] too. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
The shark fin antenna seal on my BMW failed, allowing water to enter the Telematics Control Unit (TCU). This caused a complete failure of the vehicle’s Emergency SOS / BMW Assist crash notification system. The failure occurred without any warning messages or prior indications that the system was compromised. Because the TCU controls the vehicle’s automatic crash notification and emergency call functions, this failure disabled a critical safety system. This defect placed me and my family at risk, as the vehicle would not be able to automatically contact emergency services in the event of a collision or other serious incident. The failure first occurred in April 2026. I immediately contacted my BMW dealership’s service center, where the service advisor acknowledged that the shark fin seal had issues causing this to happen (water intrusion). However, instead of treating this as a safety defect, I was told to file an insurance claim. I also contacted BMW Customer Service, but both the dealership and BMW declined responsibility and refused to cover the repair. The shark fin antenna seal is a manufacturer‑installed, non‑serviceable component. Its failure directly disabled a federally regulated safety system without warning. BMW’s refusal to address this issue leaves the safety defect unresolved and exposes other owners to the same risk.
The contact owns a 2019 BMW X7. The contact stated that while driving at an undisclosed speed, the engine overheated and the engine seized. The check engine warning light was illuminated. While attempting to restart the vehicle, the vehicle restarted with the power train warning light illuminated. The vehicle was taken to the dealer; however, the vehicle was not diagnosed, and the failure reoccurred. The failure was a persistent failure. The contact stated that there was thick white smoke coming from the exhaust. The contact noticed a fuel odor on the interior and exterior of the vehicle. In addition, the RPM was elevated. The vehicle was towed to the dealer. The contact stated that the failure was a known failure with the vehicle. The manufacturer was made aware of the failure but provided no assistance. The contact was informed that the repair was not covered under recall or warranty. The failure mileage was approximately 102,000.
I am reporting a safety concern involving BMW vehicles equipped with the B58 Technical Update (B58TU) engine, commonly found in model years 2019–2021. These vehicles use a variable-displacement oil pump with an internal thermoplastic component that regulates oil pressure. This component is increasingly failing in the field, often fracturing and causing sudden loss or instability of oil pressure. Failures commonly occur during cold starts in low temperatures. When the component breaks, oil pressure may become erratic or drop entirely, often with little or no warning before engine damage or vehicle shutdown. Early warning signs can include inability to measure oil level, abnormal oil pressure behavior, or drivetrain malfunction alerts. In many cases, failures quickly lead to engine shutdown or severe damage due to oil starvation. This can leave vehicles suddenly disabled while driving or shortly after startup, creating a safety risk—especially in traffic or in cold weather, where occupants may be exposed to freezing conditions while waiting for assistance. Repair requires extensive disassembly, with oil pump replacement alone typically costing $6,000–$8,000, excluding additional engine damage. Owners also cannot reliably determine whether their vehicle has the original thermoplastic component or an updated metal version, as parts databases now default to the revised design regardless of what is actually installed. Failures have been reported across multiple model years, and the full scope of affected vehicles remains unclear. Because this issue can cause sudden vehicle disablement without adequate warning—particularly in cold conditions—it may represent a safety-related defect warranting investigation.
BMW has a known issue that the fin antenna on the roof leaks and sets off a cascade of dangerous issues with the Emergency Call function and disabling the heads up dash so that you cannot see your navigation. On April 2, 2026 in Austin, TX it rained and our car started sending an Emergency Call request repeatedly to BMW. BMW operators called repeatedly even though they knew there was no emergency and that they were actively interrupting our driving. The heads up dash would not allow us to see our maps to navigate, but only displayed a notification that an Emergency Call had been initiated. BMW needs to address and recall this antenna seal so that owners can use their cars safely (with all functions) while not paying out of pocket for BMW's failure.
Safety Defect Report — Engine Oil Pump Failure (BMW B58TU Engine) Component or System Involved The failure involves the variable-displacement engine oil pump installed in BMW vehicles equipped with the B58 Technical Update (B58TU) engine, commonly found in model years 2019–2021. The oil pump contains an internal thermoplastic adjusting component that regulates engine oil pressure. Field reports indicate this internal component can fracture, causing unstable or complete loss of engine oil pressure. The failed component may be available for inspection upon request if retained after repair. Description of Failure and Safety Risk When the internal thermoplastic adjusting component fails, engine oil pressure regulation becomes erratic or is lost entirely. This results in insufficient engine lubrication and may cause sudden engine shutdown or severe mechanical damage due to oil starvation. Loss of engine power or complete engine disablement can occur without adequate warning, creating a safety hazard if the vehicle becomes immobilized while driving or shortly after startup. This risk is heightened when the failure occurs in active traffic or in cold weather conditions, where occupants may be exposed to freezing temperatures while awaiting assistance. Operating Conditions and Failure Pattern The failure most frequently occurs during cold-start operation in low ambient temperatures. Failures appear to progress rapidly once symptoms begin. Warning Lamps, Messages, or Prior Symptoms Reported precursor symptoms may include: Inability to electronically measure engine oil level. Abnormal or unstable oil pressure behavior. Sudden drivetrain malfunction warnings. Minimal or no actionable warning prior to engine damage or shutdown. These symptoms may appear shortly before failure or may not provide sufficient time for corrective action. Inspection or Confirmation of the Problem Field failures have been reported across multiple vehicles and production years. In many cases
Transfer case goes bad on all 2019 models. I'm in awe that there's not a recall on it. A replacement costs around $9k. Somebody should look into this. Thank you
My car was not starting up, I sent to my mechanic and we got it fixed. But have to change my starter , I tried to buy the starter from bmw they told me I have a recall and I can’t purchase that part until I send the car to a dealership. The car is been shipped out of the country and it’s in Ghana now. Please I really need your help to make this purchase and clear the recall
The contact owns a 2019 BMW X7. The contact stated that while driving approximately 40 MPH, the vehicle started to vibrate, and the vehicle lost motive power. The contact stated that the message "Timing Chain Failure - Contact Manufacturer" was displayed. The contact had taken the vehicle to a local dealer, where it was diagnosed and determined that there was no failure. The vehicle was not repaired. The contact stated that the loss of motive power and vibration was a recurring failure and occurred at 40 MPH or faster. The manufacturer was informed of the failure and was advised that there was no recall related to the failure, and referred the contact to the dealer. The failure mileage was approximately 50,000.
My 2019 BMW X7 is under Safety Recall 25V-644 for an overheating/fire-risk defect, but the recall remedy is unavailable. The vehicle has now experienced multiple safety-related failures that appear to be progressing. BMW diagnosed the following failures: • Emergency Call System Malfunction • GPS and maps not working • Failure of the TCB telematics module • Failure of the antenna and TCB battery due to fluid ingress • Battery voltage in the red zone • All four tire pressure sensors beginning to fail • Collapsed engine mounts attributed to heat • $11,296 in repair estimates related to electrical and heat damage Immediately after picking up the vehicle from BMW service, a new battery/charging system warning light appeared that was NOT present before the visit. This suggests further deterioration of the electrical system. The combination of: • an open fire-risk recall with no fix available, • fluid ingress damaging telematics components, • multiple electrical and safety-system failures, and • new warning lights appearing after service makes this vehicle unsafe to operate, especially for long-distance highway travel. I am requesting that NHTSA document this as a safety-defect case and assist in ensuring BMW provides a safe resolution.
the transfer case for this 2019 is failing, and cannot be repaired without changing the entire case according to the mechanic notes. there is a significant grinding when turning at slow speeds and a locking-up feeling to the steering. dealer will not admit to any issues. car was inspected by an independent certified BMW mechanic no warning or indication given other than the impaired handling of the vehicle.
Filed by owners of this model year and unverified by NHTSA — one person’s account, not an established fact.