2017 BMW X3
6 recalls and 92 owner complaints on record for this model year.
Check a specific vehicle
This page describes the model. To see how one particular car is equipped, and whether its identifier is valid, decode its VIN.
Decode a VIN6 recalls and 92 owner complaints on record for this model year.
This page describes the model. To see how one particular car is equipped, and whether its identifier is valid, decode its VIN.
Decode a VINAlmost all of this describes the model year, not the individual car. Nothing here can tell you about this vehicle’s mileage, accidents or ownership — no identifier encodes those.
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2013-2018 328d, 328d xDrive, 2014-2018 328d Sports Wagon, 328d xDrive Sports Wagon, 2014-2016 535d, 535d xDrive, 2015 740Ld xDrive, 2015-2017 X3 xDrive28d SAV, and 2014-2017 X5 xDrive35d SAV diesel vehicles equipped with an Exhaust Gas Recirculation (EGR) module with an integrated cooler. The EGR cooler may leak internally, causing coolant to mix with diesel engine soot, which could result in smoldering particles and a melting intake manifold.
Remedy: Dealers will replace the EGR cooler and inspect the intake manifold, replacing it as necessary, free of charge. This recall includes all vehicles previously recalled under 18V-755. Vehicles previously recalled under 18V-755 will need to have the new remedy performed for this recall. An interim owner notification letter was mailed on January 18, 2022. The remedy is expected to be available in June 2022. Owner notification letters were mailed on July 6, 2022. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2014-2018 328d, 328d xDrive, X5 xDrive35d, 2014-2016 535d, 535d xDrive, 2015 740Ld xDrive, and 2015-2017 X3 xDrive28d vehicles. The high-pressure fuel pump may fail.
Remedy: Dealers will replace the high-pressure fuel pump, free of charge. Owner notification letters were mailed on January 14, 2022. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2013-2018 BMW 328d and 328d xDrive, 2014-2018 328d Sports Wagon and 328d xDrive Sports Wagon, 2014-2016 535d and 535d xDrive, 2015 740Ld xDrive, 2015-2017 X3 xDrive28d SAV and 2014-2017 X5 xDrive35d SAV vehicles equipped with an Exhaust Gas Recirculation (EGR) module with an integrated cooler. If the EGR cooler leaks internally, the coolant can mix with diesel engine soot. The high EGR temperatures may result in these particles possibly smoldering and melting the intake manifold.
Remedy: BMW will notify owners, and dealers will inspect and replace the EGR cooler as necessary. If a leak has already occurred, the engine intake manifold will also be replaced. These repairs will be made free of charge. The recall began May 13, 2019. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling one model year 2017 BMW X3 xDrive 28i vehicle manufactured on June 7, 2016. This vehicle has electronic power steering (EPS), and the contact pins on the EPS control unit may not have been welded properly resulting in increased resistance.
Remedy: The vehicle was repaired at the dealership before sale. Therefore, an owner notification notice will not be issued for this campaign. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain model year 2011-2017, X3 sDrive28i, X3 xDrive28i and X3 xDrive35i, vehicles manufactured July 2, 2010 to April 14, 2016, 2015-2017 X3 xDrive28d vehicles manufactured March 10, 2014 to March 31, 2016, and 2015-2017 x4 xDrive28i, X4 xDrive35i and X4 xDriveM40i vehicles manufactured March3, 2014 to April 15, 2016. The affected vehicles have lower anchor bars for securing child restraint seats that may become damaged when using the European-ISOFIX-type, rigid-style connector, child restraint system.
Remedy: BMW will notify owners, and dealers will weld a reinforcing bracket to the lower anchor bars and the vehicle body, free of charge. The recall began on July 13, 2016. Owners may contact BMW customer service at 1-800-525-7417.
Published by model year, not by VIN — may not apply to this vehicle, or may already have been done. Confirm with a dealer.
Water may come into contact with the starter relay and gradually cause corrosion. This could affect the electrical connection inside the relay and make the engine difficult to start. It may also result in a short circuit and could cause the starter to overheat leading to a fire when the vehicle is in motion or when it is parked with the ignition off. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Due to a manufacturing failure, the protection of the two outer headrests in the second row is reduced. In the event of a collision or accident, passengers could be injured. In addition, headrest parts may become exposed and also cause serious injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The RSW22 starter with reinforced water tightness (RWT) may experience increased abrasion of the magnetic contact, causing deposits to build up at the lowest point inside the relay. These deposits may increase relay contact resistance, leading to starting failures or short circuits. If a short circuit occurs, either when attempting to start the vehicle or while driving due to vibration-related movement of the deposits, it could cause a thermal event and increase the risk of fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Damaged brake discs may have been fitted to the front axle. This can lead the brakes to fail when a heavy load is placed on the wheel concerned, increasing the risk of accident and injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Failure to bolt the plus voltage (B+) cable tightly enough to the starter generator may result in contact problems and an increase in contact resistance at the bolted connection. This may in turn lead to local overheating and the vehicle catching fire or to the engine stalling while the vehicle is coasting. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The positive battery cable of the starter-generator may not have been manufactured correctly. This could result in a loose electrical connection, leading to excessive contact resistance. The vehicle cannot charge or start. Contact points in the starter-generator could overheat and cause a vehicle fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the inflator of the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments of the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The driver airbag inflator may malfunction due to long-term degradation. In this case, if the airbag is deployed in an accident, the internal pressure in the inflator may be too high. The inflator could burst. Metal fragments may cause injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The failure concerns the RSW22 starter, type RWT (reinforced for watertightness). Increased abrasion of the magnetic contact can lead to the formation of deposits at the lowest point of the relay interior. This in turn can increase the resistance of the relay contact, causing accidental ignition or even short circuits, possibly leading to a thermal reaction and fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The failure concerns the RSW22 starter, type RWT (reinforced for watertightness). Increased abrasion of the magnetic contact can lead to the formation of deposits at the lowest point of the relay interior. This in turn can increase the resistance of the relay contact, causing accidental ignition or even short circuits, possibly leading to a thermal reaction and fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The failure concerns the RSW22 starter, type RWT (reinforced for watertightness). Increased abrasion of the magnetic contact can lead to the formation of deposits at the lowest point of the relay interior. This in turn can increase the resistance of the relay contact, causing accidental ignition or even short circuits, possibly leading to a thermal reaction and fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The steering system sensor may malfunction causing an unintended steering movement of the vehicle. This increases the risk of accidents and injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The screw connection of the servo unit on the gear rack casing of the steering system may be faulty. This could cause the steering system to fail and become blocked, increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Due to faulty rear-most screws, the screw fixings of the boot's lashing rails can fail in the event of a rear-end collision with heavy intrusion and penetrate the backs of the rear seats. This increases the risk of injury to the occupants of the rear seats. The vehicles concerned have already been modified in connection with the recall code 0051960500. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant within the integrated inflator of driver airbags can deteriorate during time. If the airbag deploys, it could result in fragments from the inflator casing injuring the vehicle’s occupants. The product does not comply with the Regulation on the approval and market surveillance of Motor Vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Due to faulty rear-most screws, the screw fixings of the boot's lashing rails can fail in the event of a rear-end collision with heavy intrusion, and penetrate the backs of the rear seats. This increases the risk of injury to the occupants of the rear seats. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
A seam on the inflator housing of the driver airbag may not have been correctly welded. In case of accident, when the airbag is deployed, the inflator can burst, releasing metal parts which could cause injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The driver's airbag inflator propellant may deteriorate over time. If activated during an accident, excessive internal pressure may cause the inflator to burst, and metal fragments could pass through the cushion material causing injury to occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Due to a manufacturing error, the weld seam of the integrated transmission control unit (ITCU) may not have been correctly executed. As a result, transmission oil could leak into the ITCU, causing it to fail. This may lead to transmission seizure, increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Matched on brand and model name — Safety Gate publishes no VIN. Check the production dates, and quote the recall code to a dealer.
NOTIFYING YOU OF A SAFETY MATTER THAT THE CONSTITUENT EXPERIENCED WHILE DRIVING HIS SON'S 2017 BMW X3 ON JUNE 29TH A APPROXIMATELY 6:30PM INVOLVING THE VEHICLES FRONT AND SIDE AIRBAGS. *LD THE CONSUMER STATED THE AIRBAGS DEPLOYED FOR UNKNOWN REASONS. THE DRIVER CRASHED INTO A GUARD RAILED. THE DRIVER AND 2 PASSENGERS RECEIVED BRUISES FROM THE IMPACT. THEY WERE TRANSPORTED TO THE HOSPITAL FOR OBSERVATION. UPDATED 09/11/2017*JS
While driving on the freeway my brakes failed. I had pushed the pedal all the way down and the vehicle was still moving. This caused a rear end collision. There were no warnings that appeared.
I LEASED A 2017 BMW X3 WITH 3370 MILES ON IT SO ALMOST BRAND NEW. I HAVE A 7.6 MILE COMMUTE FROM WORK TO HOME. I WAS DRIVING HOME FROM WORK AROUND 230PM PST SOUTH ON THE 405 (HIGHWAY) IN LOS ANGELES. I PULL UP TO MY HOUSE AND PARK THE VEHICLE ON MY CITY STREET. I PARK TURN OFF THE VEHICLE AND LOCK THE DOORS AND WALK INTO MY HOUSE. WITHIN 15 MINUTES, MY NEIGHBOR KNOCKS ON MY DOOR AND INFORMS ME THAT MY CAR IS ON FIRE. WHEN I LOOK OUTSIDE AT MY VEHICLE, IN BETWEEN THE HOOD OF MY CAR AND FRONT WINDSHIELD ARE SPITTING FLAMES OUT ONTO THE WINDSHIELD. IT THEN PROCEEDED TO BURN FAST AND HOT AND THERE WERE 30 FOOT FLAMES THAT HAD RUINED OUR FENCE AS WELL AS SINGED OUR NEIGHBORS TREE. THE FIRE DEPARTMENT CAME AND FINALLY TOOK OUT THE FLAME BUT THE VEHICLE WAS COMPLETELY RUINED. THE TOW TRUCK SHOWED UP LATER BUT HE REFUSED TO TOW THE VEHICLE BECAUSE HE SAW SMOKE AGAIN. THE VEHICLE HAD CAUGHT BACK ON FIRE ON THE PASSENGER WINDOW SIDE. AIRBAGS HAD ALSO STARTED BLOWING UP WHEN THE SECOND FIRE CAUGHT. I HAD PUT MY HEAD INTO THE WINDOW WHEN THE FIRE WAS OUT TO RETRIEVE ANYTHING THAT I COULD BUT WITHIN 10 SECONDS OF PULLING MY HEAD OUT OF THE PASSENGER SIDE ANOTHER AIRBAG WENT OFF AND ALMOST TOOK OFF MY HEAD. THERE WAS A DUAL INVESTIGATION WITH BMW AND MY INSURANCE SAFECO. THE INVESTIGATION IS ONGOING. INITIAL REPORT SAID THE DEFECT HAS SOMETHING TO DO WITH THE FUEL LINE. IF THIS CAR WAS IN A GARAGE OR ANY CLOSER TO OUR HOUSE EVERYTHING WOULD HAVE GONE UP IN FLAMES. OUR STORY WAS ON THE NEWS AS WELL. THERE WAS NO KNOWN RECALL ON THIS VEHICLE AS I HAVE CHECKED EVERYWHERE. HTTPS://ABC7.COM/LA-FAMILY-DEMANDS-ANSWERS-AFTER-PARKED-BMW-CATCHES-FIRE/4213154/ HTTPS://WWW.NBCLOSANGELES.COM/NEWS/LOCAL/BMW-SPONTANEOUSLY-COMBUSTS-PARKED-ON-LA-STREET-493018841.HTML HTTPS://KTLA.COM/2018/09/13/PARKED-BMW-MYSTERIOUSLY-CATCHES-FIRE-IN-WESTCHESTER/
ENGINE SEIZED AT 65MPH HIGHWAY SPEEDS DURING COMMUTE TO WORK ON BUSY BOSTON HIGHWAY. NARROWLY AVOIDED SEVERAL COLLISIONS AS VEHICLE COASTED TO STOP. VEHICLE WAS PURCHASED NEW FROM A BMW DEALER THREE WEEKS AGO AND HAS LESS THAN 2,000 MILES ON IT. DEALER ADVISES AN "OVERSIZED BEARING WAS FOUND IN THE ENGINE CAUSING IT TO OVERHEAT AND SEIZE". ENGINE REQUIRES REPLACEMENT. TRANSMISSION, TRANSFER CASE, ELECTRONICS AND COOLING SYSTEM DAMAGE ARE SUSPECTED BY THE DEALER TECH AND WILL REQUIRE MONITORING.
The contact owns a 2017 BMW X3. The contact stated that while the contact's wife was pulling into a driveway, the vehicle sporadically accelerated and crashed into another vehicle. The contact stated that his wife was pumping the brakes but the vehicle failed to stop immediately. No air bags were deployed. The contact's wife was not injured and did not receive medical attention. A police report was filed. The vehicle was towed to a repair shop. The manufacturer was made aware of the failure. The approximate failure mileage was 100,000. The VIN was not available.
As I was pulling into my assigned parking spot in my building complex. Both me and my 6yr old daughter were in the vehicle. As I was pulling into my parking spot and went to brake and put my vehicle in park- my brakes locked, gave out and the vehicle continued to proceed forward. As it proceeded forwarded, I immediately kept trying to brake- but because the vehicle is all wheel drive it accelerated forward pushing through the concrete parking bumper guard located on the floor of the parking spot. Because of the acceleration, the vehicle crashed into the storage units connected to the building structure. I immediately tried reversing and forced the car into park without braking. Thankfully my daughter was still in her car seat. It was terrifying and we were in so much panic and scared. My neighbors came to our rescue- because I was distraught knowing that we had literally just come off of the highway and that could have happened at any point with my child in the car. My insurance is able to cover the damages - but, the auto repairs do not consist of checking the brakes/malfunction. I cannot see myself staying with this vehicle and putting the safety of myself and daughter in jeopardy. I am praying that BMW takes the necessary measures to assist in addressing this
TL* THE CONTACT OWNS A 2017 BMW X3. THE CONTACT WAS ATTEMPTING TO STOP AT A STOP SIGN AND PRESSED DOWN ON THE BRAKE PEDAL BUT THE VEHICLE ACCELERATED. THE VEHICLE HIT ANOTHER VEHICLE STOPPED IN FRONT AT THE STOP SIGN. THERE WERE NO INJURIES AND A POLICE REPORT WAS NOT FILED. THE VEHICLE HIT THE BACK BUMPER OF THE OTHER VEHICLE AT 5 MPH. THERE WAS NO VISIBLE DAMAGE WITH ONLY THE LICENSE PLATE BEING TORN OFF. THE DEALER AND MANUFACTURER HAD NOT YET BEEN CALLED. THE OTHER PERSON FILED A CLAIM WITH THE CONTACT'S INSURANCE COMPANY. THE FAILURE MILEAGE WAS 16,420.
I WAS STOPPED AT A TRAFFIC LIGHT AND WITHOUT WARNING THE CAR ACCELERATED. I SIDESWIPED THE CAR IN FRONT OF ME AND PROCEED TO CROSS A 4 LANE HIGHWAY. I TRIED TO STOP BUT KEPT GOING , JUMPED A CURB GOT ON A GRASSY AREA DID A 360 TO A ROAD JUMPED BACK ON THE GRASS AND CAME TO REST IN SOME BUSHES AND WIRE FENCE. DAMAGE TO DRIVERS SIDE FRONT END. IHAVE PICTURES IN MY PHONE, BUT DON'T KNOW HOW TO ATTACH THEM TO THIS FORM?
CAUSING THE CAR TO JUMP FORWARD. BY PUTTING CAR IN NEUTRAL AND DEPRESSING THE BRAKE ON A GRADE, WHEN I HAD COMPLETED, I NOTICED THE THE RPM GAGE WAS AT 4000 RPM WITH BRAKE ON. THE VEHICLE WAS STATIONARY AT THE TIME. THREE TIMES IT HAS HAPPENED AS I SLOWED DOWN AND IT LURCHED FORWARD STRIKING OBSTICALLS. WHEN BRAKING IT POSSIBLE TO ENGAGE THE GAS PEDAL
AUGUST 19, 2017 I PULLED INTO MY DRIVEWAY AT A VERY LOW SPEED AND APPLIED THE BRAKES TO PARK. THE CAR AGGRESSIVELY ACCELERATED EVEN THOUGH MY FOOT WAS ON THE BRAKE. THE CAR WENT THROUGH MY NEIGHBORS FENCES AND IT FINALLY STOPPED BETWEEN TWO GARAGES BEHIND MY PROPERTY ON THE NEXT STREET. I COULD NOT OPEN THE DOORS OR WINDOWS FOR A MINUTE OR TWO. I DO NOT FEEL SAFE DRIVING THIS CAR AGAIN.
I WAS STOPPING MY CAR AT A RED SIGNAL BEHIND ANOTHER VEHICLE. I APPLIED BREAKS AND VEHICLE REACHED TO COMPLETE STOP. IMMEDIATELY, ENGINE PICKED UP AND STARTED MOVING FORWARD EVEN THOUGH BREAKS ARE COMPLETELY PRESSED. I HAD TO DO SOMETHING TO STOP THE CAR REAR ENDING. SO, I RELEASED AND RE-APPLIED BREAKS. VEHICLE REACHED COMPLETE STOP AND AGAIN STARTED ACCELERATING FORWARD. I REPEATED THE PROCESS BUT THE THIRD TIME IT HIT THE CAR INFRONT OF ME. THE CAR IS EQUIPPED WITH : AUTO START/STOP ENGINE (WHICH STOPS THE ENGINE WHEN THE CAR IS AT COMPLETE REST). AUTO HOLD (WHICH ALLOWS THE DRIVER TO TAKE THE FOOT OFF OF THE BREAK) BOTH THE FUNCTIONALITY ARE TURNED ON WHEN THE INCIDENT HAPPENED, BUT I DIDNT TAKE OFF MY FOOT FROM THE BREAK PEDAL. ALSO, AC WAS RUNNING. I FOUND ANOTHER DRIVER COMPLAINING THE SAME ONLINE. HTTP://WWW.BIMMERFEST.COM/FORUMS/ARCHIVE/INDEX.PHP/T-766433.HTML
I have tried to set up an appointment with my local dealer for a recall notice several times, but they never have the part needed. One time they said they had the part and after dropping the car off my wife returned to find out they still did not have the part The date below is approximate
Seat mat sensor module which detects presence of passenger in the seat has malfunctioned sooner than expected.
See attached document for complaint. It is coming to almost a year that this problem still exists. After multiple attempts to have this rectified still un settled. I tried to make a claim on your website but for some reason the site is not taking my VIN# XXXXXXXXXXXXXXXXX, NJ Plate Tag XXXXXX
I have an open recall on my vehicle that has not yet been repaired, and I’ve reached out to BMW multiple times and still haven’t received a letter from them regarding this Recall! If the vehicle can potentially catch fire then why would they think this isn’t a priority due to safety concerns!!!!
Filed by owners of this model year and unverified by NHTSA — one person’s account, not an established fact.