2018 BMW X1
4 recalls and 59 owner complaints on record for this model year.
Check a specific vehicle
This page describes the model. To see how one particular car is equipped, and whether its identifier is valid, decode its VIN.
Decode a VIN4 recalls and 59 owner complaints on record for this model year.
This page describes the model. To see how one particular car is equipped, and whether its identifier is valid, decode its VIN.
Decode a VINAlmost all of this describes the model year, not the individual car. Nothing here can tell you about this vehicle’s mileage, accidents or ownership — no identifier encodes those.
BMW of North America, LLC (BMW) is recalling certain 2018-2019 BMW X1 sDrive28i, X1 xDrive28i, 2019 X2 xDrive28i, MINI Cooper S Convertible, Countryman, and John Cooper Works Countryman vehicles. The steering gear tie rod may have been assembled incorrectly, which may result in excessive wear of the tie rod end, eventually causing it to break.
Remedy: BMW will notify owners, and dealers will inspect the vehicles and replace the tie rods and ball joints as necessary, free of charge. The recall began October 11, 2019. Owners may contact BMW customer service at 1-800-525-7417 or MINI customer service at 1-866-825-1525.
BMW of North America, LLC (BMW) is recalling certain 2016-2019 X1 sDrive28i and X1 xDrive28i vehicles. In the event of a crash where the occupants head contacts the B-pillar, the pillar may not absorb an adequate amount of the impact. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 201, "Occupant Protection in Interior Impact."
Remedy: BMW will notify owners, and dealers will replace the vertical trim pieces on the upper portion of the interior B-Pillars, free of charge. Interim letters notifying owners of the safety risk were mailed July 1, 2019. Second notices will be sent as parts become available, starting on September 27, 2019. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2018-2019 BMW X1 sDrive28i and X1 xDrive28i vehicles. Contaminated hardware may cause the attachment brackets of the taillight housings to crack, causing the lights to loosen or possibly detach from the vehicle.
Remedy: BMW will notify owners, and dealers will properly secure the taillights, free of charge. The recall began March 28, 2019. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2018 BMW 540d xDrive vehicles. The crankshaft sensor may be equipped with incorrect firmware, preventing the sensor from properly processing input from the crankshaft reluctor ring, possibly resulting in a vehicle stall. On September 12, 2018, BMW expanded the recall to a total of 5,309 vehicles including certain 2018-2019 BMW 540d xDrive, 230i M240i, M240i xDrive, X2 sDrive28i, X2 xDrive28i, X1 sDrive28i, X1 xDrive28i, 330i, 330i xDrive, 340i, 340i xDrive, 330i xDrive Gran Turismo, 530i, 530i xDrive, 540i, 540i xDrive, 530e, 530e xDrive, 640i xDrive Gran Turismo, 330e, 2019 430i Gran Coupe, 430i xDrive Gran Coupe, 440i Gran Coupe, 440i xDrive Gran Coupe, 430i, 430i xDrive, 440i, 440i xDrive, 740i, 740i xDrive, MINI Cooper, Cooper S, JCW, MINI Countryman (Cooper, Cooper All4, Cooper S, Cooper S All4, JCW All4), and MINI Clubman (Cooper, Cooper S, Cooper All4, Cooper S All4, JCW All4) vehicles.
Remedy: BMW will notify owners, and dealers will replace the crankshaft sensor, free of charge. The recall began September 6, 2018. Owners may contact BMW customer service at 1-800-525-7417.
Published by model year, not by VIN — may not apply to this vehicle, or may already have been done. Confirm with a dealer.
The seatbelts in the second row may not have been manufactured correctly and could cause the car-sensitivity sensors to fail. This could reduce the protective effect of the seatbelts and lead to injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The seat belts of the car were not manufactured correctly. In the event of a collision or accident, the restraint function of the seat belts may be reduced and may not provide the necessary protection. As a result, there may be an increased risk of injury. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The cell modules in the vehicles concerned were not produced in accordance with the specifications, which may cause the module frame to fail. This may lead to a shutdown of the high-voltage system and fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The material used for the B-pillar reinforcement plates is inadequate. This can alter the crash characteristics, leading to an increased risk of injuries in the event of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the inflator of the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments of the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The driver airbag inflator may malfunction due to long-term degradation. In this case, if the airbag is deployed in an accident, the internal pressure in the inflator may be too high. The inflator could burst. Metal fragments may cause injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The hollow shaft of the servomotor was not welded correctly. The weld may not be able to withstand high braking pressure build-up and may break. In this case, the reduced braking performance requires greater force and the braking distance may increase. In addition, the ABS and DSC brake control systems are not assisted. This increases the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant within the integrated inflator of driver airbags can deteriorate during time. If the airbag deploys, it could result in fragments from the inflator casing injuring the vehicle’s occupants. The product does not comply with the Regulation on the approval and market surveillance of Motor Vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The front left seat's height adjustment mechanism may have been incorrectly riveted, potentially compromising the seat's structural integrity. In an accident, this could have a negative impact on the restraint system and increase the risk of injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The seat recliner adjuster may not be correctly welded, which could cause the backrest not to lock. If it doesn't lock, the seatback might not stay secure in a collision, increasing the risk of injury. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The integrated braking system could be compromised, which could lead to an unexpected failure of the hydraulic braking assistance, thereby requiring greater pressure on the brake pedal. This can result in a longer braking distance, as well as failure of the Anti-lock Braking System (ABS) and the Dynamic Stability Control (DSC), increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Matched on brand and model name — Safety Gate publishes no VIN. Check the production dates, and quote the recall code to a dealer.
Serious highway accident in Chicago suburbs whereby car was totaled. Engine came away from chassis after ramming into and taking out 50 feet of guardrail and coming to a screeching halt. Left front wheel came away from vehicle in its entirety. No front, side or overhead airbags deployed whatsoever. Traveling at 50MPH at time of accident. I have pictures if required.
Airbag. No open recalls. Spinal injury in head-on collision. Unknown Crash Champions at Windsor Mills in Baltimore, MD (auto body shop for Progressive) No warnings
This was struck in the rear at the stop light.
I was in a 3-car accident through the fault of another driver. This was on a highway in northwest suburbs of Chicago. Very serious crash ending in a totaled vehicle. Severe (left) front end damage with engine disengaging from the chassis and left front wheel coming off vehicle. I believe I was put at high risk of losing my life because none of the airbags deployed inside the vehicle. The car was viewed by state police (police report available) and insurance representatives officially deeming the vehicle "totaled". Based on my VIN, there were no pending airbag recalls on file. See uploaded pictures
TAILGATE LOCKING SYSTEM HAS ELECTRONIC KICK. THERE IS NO ELECTRONIC CHIRP TO ALERT CLOSING. I WAS STRUCK IN THE HEAD. THE TOP LATCH IS WAS REVERSED TO 'MALE' EQUIVALENT TO A HAMMER. THE BOTTOM LATCH WAS REVERSED AS CONNECTOR. IF ANYONE OVER 5' 10" WALKS UNDER THE OPEN HATCH THEY CAN BE STRUCK.
On the evening of July 10, 2025, while driving a 2018 BMW X1, I experienced a sudden cascade of dashboard alerts, including warnings for the airbag, chassis system, and right signal headlight. The system advised moderate driving and service. Moments later, all dashboard lights activated simultaneously. I pulled over and placed the vehicle in park. Within seconds, smoke began rising from the front-right corner of the engine compartment, followed by visible flames. My daughter was in the car with me. We had to evacuate immediately, and contacted emergency services from the roadside. The fire was extinguished by first responders, and the vehicle was later towed. This event put both of us in immediate danger. It occurred just five days after service on the right front headlight was performed by an authorized dealership. While the issue has not yet been confirmed by the manufacturer or service center, the timing and location raise serious concerns. The vehicle was inspected by the fire department, and an insurance claim is currently under investigation.
THE CAR HAD 14,500 MILES ON IT WHEN THE PROBLEM OCCURED. MY WIFE DROVE THE CAR TO CHICAGO AND BACK , UPON RETURNING SHE PARKED THE CAR IN THE GARAGE REMOVED SOME GROCERIES THE CAME BACK TO GET THE REST AND THE CAR WAS SMOKING FROM UNDER THE HOOD. SHE THEN CALLED ME AS I WAS NOT HOME AND ASKED WHAT TO DO, I TOLD HER TO GET THE CAR OUT OF THE GARAGE AND BECAUSE OF THE INTENSE SMOKE SAID SHE WAS AFRAID SO I TOLD HER TO CALL THE FIRE DEPT. WHICH SHE DID. 30 MINUTES LATTER THE CAR AND GARAGE AND ALL CONTENTS WERE DESTROYED.
This vehicle was rear ended with rear frame damage. The airbag light stays on and the seat belt was ejected and lock. The seat now will not extend to fit and latch. My wife the owner of the car [XXX] head and body was jerked extremely hard due to the lack of airbag not deploying. My wife completed all required maintenance with the BMW dealer prior to the accident. This is frustrating since we paid a lot of money over the years to maintain the car and we expect nothing less, but a safe vehicle for my wife. [XXX] [XXX] [XXX] [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
At-fault vehicle (charged with improper lane usage) in Toyota Corolla attempted to abruptly merge left from "local lanes" going north of IL 53 to the "express" lanes hitting a Toyota Camry which veered into my front right tossing me across 3 lanes taking out 70' of guardrail and totaling my 2018 BMW X1. My airbags did not deploy. My engine came away from the chassis and left front wheel came away from the vehicle as well. It is my opinion at least one airbag/safety restraint should have been deployed. I submitted a report to this department February 1, 2022. I heard back in June and nothing else ever happened even after I submitted the requested information. See the email stream last week from [XXX], HR, NHTSA-----> Good morning [XXX], I reviewed the documents you sent me and it appears you submitted everything [XXX] requested. The information my contact gave me is as follows: “The customer can go to the NHTSA Report a Safety Problem web page on NHTSA’s public webpage (link below) and complete the required information. They can also call the toll free number at 888-327-4236, Monday-Friday 8am-8pm ET to report as well. Report a Vehicle Safety Problem, Equipment Issue | NHTSA” Let them know you submitted your complaint back on February 1, 2022, and [XXX] contacted you and requested additional information to include the location of the incident, the Police Accident Report (you submitted), nature of injuries (you submitted), the event recorder report (which you notified him that you did not have), and manufacturer complaint number (which you provided to him). The last time you heard from him was June 10, 2022 when he requested the additional information and you provided the information later that day. Let them know you are trying to bring closure to this matter. I hope this helps! [XXX], HR, NHTSA INFORMATION Redacted PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).
On May 20, 2026 We were in Mt Dora, FL We were approaching a red light. Cars were stopped in front of us and cars were beside me and behind me. As I slowed down the car just stalled out. It completely turned off while I was in drive. I immediately tried to start it. Then I put my foot on the brake and put it in park and turned on my hazard lights. I waited about 3 minutes and started it up. It was so scary because we could have been hit from behind.
• What component or system failed or malfunctioned, and is it available for inspection upon request? I have a 2018 BMW X1 that has about 60,000 miles on it. So far, I have had to have the windshield replaced four times due to pebbles hitting and cracking the windshield when on the highway. This never used to be the case in older BMWs that I have had in the past. Pebbles would never crack windshields. I know many other friends and family members that have had the same issue. Although insurance pays for the windshield/sensor replacements that cost around $1,500 to $2,700 (depending on which dealership I go to and which state I have lived in), this results in higher premiums for us all, because insurance companies are not going to just take a loss on the windshield claims. So really, we are all paying for each other's windshields with our insurance premium increases. Please enforce a recall to replace all the weak windshields with the strong windshields they used to produce. They are not only wasting our money but profiting off the insurance payments for all these broken windshields. My car is available for inspection upon request. • How was your safety or the safety of others put at risk? Cracked windshields compromise the vehicle's structural integrity, distorts your vision, and can shatter if subjected to sudden temperature changes, road vibrations, or a collision. • Has the problem been reproduced or confirmed by a dealer or independent service center? Yes, every time I go into a BMW dealership to have the windshield replaced and by my insurance company, which pays for the replacements. • Has the vehicle or component been inspected by the manufacturer, police, insurance representatives or others? Yes, by BMW dealerships when they have replaced the windshield each time. • Were there any warning lamps, messages or other symptoms of the problem prior to the failure, and when did they first appear? No
The contact owns a 2018 BMW X1. The contact stated that while driving approximately 40 MPH, the check engine and engine overheating warning lights became illuminated. The vehicle was taken to an independent mechanic to be diagnosed, and it was determined that the water pump needed to be replaced. The contact had an older BMW that had experienced the same failure, and the vehicle was included in NHTSA Campaign Number: 24V608000 (Engine and Engine Cooling, Electrical System). The local dealer was contact and the contact was informed that the current vehicle was not included in the recall. The vehicle was not repaired. The manufacturer was not informed of the failure. The failure mileage was approximately 80,000.
While driving my vehicle at normal highway and city speeds, I noticed a serious steering issue where the steering wheel feels excessively loose and unresponsive. The vehicle does not track straight and constantly drifts left and right, requiring continuous steering corrections to keep it within the lane. The steering feels vague and unstable, as if there is excessive play in the steering system. At times, small steering inputs result in delayed or inconsistent vehicle response, making it difficult to maintain a straight path. This issue occurs on smooth, dry roads and is not related to road conditions, wind, or tire pressure. This condition creates a significant safety concern, especially at higher speeds, as it feels like I could lose control of the vehicle or unintentionally drift into another lane or off the road. The problem has been persistent and appears to be worsening over time.
In November I noticed a noise when steering. I took my suv to the mechanic shop and they located the following recall from your website: recall 19V601000 the tie rod assembly. I contacted BMW of North America and they cannot locate this recall with my VIN.
The contact owns a 2018 BMW X1. The contact stated that while driving at various speeds, the vehicle lost power steering functionality. There was no warning light illuminated. The contact stated that the steering wheel was loose while turning to the left or the right. The contact stated that the failure was a reoccurring failure. The contact related the failure to NHTSA Campaign Number: 19V601000 (Steering); however, the VIN was not included. The vehicle was not diagnosed or repaired. The manufacturer was not made aware of the issue. The failure mileage was approximately 5,000.
Filed by owners of this model year and unverified by NHTSA — one person’s account, not an established fact.