2014 BMW M5
1 recall and 2 owner complaints on record for this model year.
Check a specific vehicle
This page describes the model. To see how one particular car is equipped, and whether its identifier is valid, decode its VIN.
Decode a VIN1 recall and 2 owner complaints on record for this model year.
This page describes the model. To see how one particular car is equipped, and whether its identifier is valid, decode its VIN.
Decode a VINAlmost all of this describes the model year, not the individual car. Nothing here can tell you about this vehicle’s mileage, accidents or ownership — no identifier encodes those.
BMW of North America, LLC (BMW) is recalling certain model year 2013 528i, 528i xDrive, 535i, 535i xDrive, 550i, 550i xDrive, and ActiveHybrid 5 vehicles. The rear reflex reflectors may not reflect enough light. As such, the vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 108, "Lamps, Reflective Devices, and Associated Equipment."
Remedy: BMW will notify owners, and dealers will replace the rear reflex reflectors, free of charge. The recall began July 28, 2017. Owners may contact BMW customer service at 1-800-525-7417.
Published by model year, not by VIN — may not apply to this vehicle, or may already have been done. Confirm with a dealer.
The cockpit cable harness may be damaged when the microfilter is replaced. This can lead to a short circuit, with smoke build-up resulting in fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Due to manufacturing problem, the rotation bushing of the steering column's double universal joint can break when the steering wheel is turned hard at the extreme position and when steering without steering assistance with the engine switched off. This can lead to unexpected steering behaviour which can increase the risk of accidents and injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
A seam on the inflator housing of the driver airbag may not have been correctly welded. In case of accident, when the airbag is deployed, the inflator can burst, releasing metal parts which could cause injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The integrated braking system could be compromised, which could lead to an unexpected failure of the hydraulic braking assistance, thereby requiring greater pressure on the brake pedal. This can result in a longer braking distance, as well as failure of the Anti-lock Braking System (ABS) and the Dynamic Stability Control (DSC), increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Due to a manufacturing error, the weld seam of the integrated transmission control unit (ITCU) may not have been correctly executed. As a result, transmission oil could leak into the ITCU, causing it to fail. This may lead to transmission seizure, increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Matched on brand and model name — Safety Gate publishes no VIN. Check the production dates, and quote the recall code to a dealer.
My car (a 2014 BMW M5 with only approx. 39K miles) has a known issue with defective fuel injectors (manufactured by Bosch, subsequently replaced by an upgraded part). In fact, in 2018 BMW issued me and other owners with an extended warranty for the fuel injectors for 10 years/120,000 miles (see attached copy). However, in my opinion and based on a 9/7/2022 failure incident I experienced the defective fuel injectors should have resulted in a safety recall. Previously, my car experienced a check engine light in August 2022. The dealership suspected one or more leaking fuel injectors and noted as such on my repair invoice, but I was told due to the testing protocol which BMW requires they could not replace any of the fuel injectors. BMW's testing protocol also resulted in me incurring a large bill of almost $1,100 due to the diagnosis labor involved. On 9/7/2022 while I was driving on the highway at approximately 70 miles an hour, 2 fuel injectors failed (out of 8 injectors, confirmed by subsequent repair) which resulted in a sudden and complete loss of engine power while maneuvering in traffic. I am extremely lucky the sudden loss of engine power did not result in an accident, and I was able to take a highway exit using the vehicle's momentum. Upon exiting the highway, my car's engine completely died and would not re-start. This resulted in my car obstructing the road where it almost caused several accidents and necessitated a 911 call by me to obtain police assistance to get my vehicle out of the way. After this frightening experience and due to the high failure rate I already experienced with 2 out of 8 injectors, I contacted BMW customer service and attempted to get the remaining 6 injectors replaced. BMW refuses to replace the remaining injectors and stated they would only replace a specific injector after failure. I urge the NHTSA to require BMW to perform a safety related recall for this known fuel injector issue.
BEHAVIOR OF MY CAR'S DCT TRANSMISSION HAS CREATED A DANGEROUS SITUATION WHICH ALMOST RESULTED IN AN ACCIDENT FOR ME. I BELIEVE THIS IS DUE TO A SOFTWARE CHANGE BMW MADE TO THE DCT TRANSMISSION. THE ISSUE IS AS FOLLOWS: -WHEN DRIVING AT HIGHWAY SPEED, WHEN YOU RELEASE THE THROTTLE AND LET THE VEHICLE COAST (AS WHEN YOU WANT THE VEHICLE TO NATURALLY DECELERATE WITHOUT BRAKING) THE TRANSMISSION WILL DISENGAGE THE DCT CLUTCHES. THE CAR WILL THEN MAINTAIN SPEED (AS IF CRUISE CONTROL WERE ENGAGED) INSTEAD OF NATURALLY DECELERATING. IN AND OF ITSELF, THIS BEHAVIOR IS DANGEROUS DUE TO THE FACT THE VEHICLE WILL MAINTAIN UNWANTED SPEED. -WHEN THEN TRYING TO RE-ACCELERATE QUICKLY FROM COASTING WHERE A DOWNSHIFT IS NEEDED (AS IN WHEN NEEDING TO PASS LEGALLY ON A 2 LANE HIGHWAY), THE CAR WILL NOT RE-ENGAGE THE CLUTCHES FOR A COUPLE OF SECONDS OR SO. THIS CAUSES TOTAL LOSS OF POWER OR ACCELERATION FOR 2 OR SO SECONDS. WHILE THIS MAY SEEM LIKE A RELATIVELY MINOR SITUATION, THE ABOVE SITUATION ALMOST CAUSED A SERIOUS ACCIDENT AT HIGHWAY SPEED. ALSO, MY CAR DID NOT PREVIOUSLY DISPLAY THIS BEHAVIOR UNTIL AFTER A SERVICE VISIT (I BELIEVE LAST YEAR). I SUSPECT THE DCT TRANSMISSION SOFTWARE WAS UPDATED BY BMW WITHOUT MY KNOWLEDGE AND IS THE SOURCE OF THIS CHANGE IN VEHICLE BEHAVIOR.
Filed by owners of this model year and unverified by NHTSA — one person’s account, not an established fact.