7 recalls and 20 owner complaints on record for this model year.
This page describes the model. To see how one particular car is equipped, and whether its identifier is valid, decode its VIN.
Decode a VINAlmost all of this describes the model year, not the individual car. Nothing here can tell you about this vehicle’s mileage, accidents or ownership — no identifier encodes those.
BMW of North America, LLC (BMW) is recalling certain 2025 Mini Cooper S, Mini Countryman S All4, X2, 2024 Rolls-Royce Spectre, 2023-2025 i7, 7 Series, X7, 2024-2025 i5, 5 Series, 2023-2024 XM, X1, 2024-2025 X6, and X5 vehicles. The integrated brake (IB) system may malfunction and result in a loss of power brake assist or cause the Antilock Brake (ABS) and Dynamic Stability Control (DSC) systems to not function properly.
Remedy: The Integrated brake system will be inspected and, if necessary, replaced, free of charge. Owner notification letters are expected to be mailed August 21, 2026. Owners may contact BMW customer service at 1-800-525-7417 or Rolls-Royce customer service at 1-877-877-3735. Vehicle Identification Numbers (VINs) involved in this recall will become searchable on NHTSA.gov beginning August 21, 2026. Vehicles previously repaired under recall 24V739 or 24V104 will need to have the new remedy completed.
BMW of North America, LLC (BMW) is recalling certain 2022-2025 i4, 2022-2024 IX, 2023-2024 I7, and 2024 I5 vehicles. The electric drive motor software may shut down the high-voltage system, causing a loss of drive power.
Remedy: The electric drive motor software will be updated over-the-air (OTA) or by a dealer, free of charge. Owner notification letters are expected to be mailed August 5, 2025. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America (BMW) is recalling certain 2023-2024 X1, 2024-2025 X5, 2025 X6, 2023-2025 X7, 740i, 760i, 2024 XM, 530i, 540i, i7, 750e, X2, 2024-2025 i5, 2024 Rolls Royce Spectre, 2025 MINI Countryman S ALL4, JCW Countryman ALL4, and 2025 MINI Hardtop 2 Door (Cooper, Cooper S) vehicles. Please refer to the recall report for the complete list of models. The welds in the servomotor of the integrated brake control module may break, causing a loss of power brake assist and rear brake function. In addition, the Antilock Brake System (ABS) and Dynamic Stability Control (DSC) system may not function.
Remedy: Dealers will replace the integrated brake system, free of charge. Owner notification letters were mailed November 13, 2024. Owners can contact BMW Customer Service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2024 i4 xDrive40, i4 M50 and i5 eDrive40 vehicles. The high-voltage battery module may contain insufficient weld seams, which can result in the battery overheating.
Remedy: Dealers will replace the high-voltage battery module, free of charge. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC. (BMW) is recalling certain 2023-2025 BMW, MINI, and Rolls-Royce vehicles. Please see the recall report for a complete list of models and model years. The integrated brake (IB) system may malfunction and result in a loss of power brake assist or cause the Antilock Brake (ABS) and Dynamic Stability Control (DSC) systems to not function properly.
Remedy: Dealers will replace the integrated brake system, free of charge. Owner notification letters were mailed between June and December 2024. Owners may contact BMW customer service at 1-800-525-7417 or Rolls Royce customer service at 1-877-877-3735.
BMW of North America, LLC (BMW) is recalling certain 2024 i5 eDrive40 and i5 M60 vehicles. During vehicle start-up, the artificial sound generator control unit may experience a fault and fail to generate the external pedestrian warning sound. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 141, "Minimum Sound Requirements for Hybrid and Electric Vehicles."
Remedy: Dealers will update the external artificial sound generator software, free of charge. Owner notification letters were mailed February 16, 2024. Owners may contact BMW customer service at 1-800-525-7417. Note: This is an expansion of Recall 23V-026.
BMW of North America, LLC (BMW) is recalling certain 2023-2024 740i, 740i xDrive, 760i xDrive, i7 eDrive50, i7 xDrive60, i7 M70, 2024 750e xDrive, 530i, 530i xDrive, i5 eDrive40, and i5 M60 vehicles. The ground connection to the steering wheel may not have been attached correctly, resulting in an inoperative hands-on detection system.
Remedy: Dealers will inspect and reattach the ground connection as necessary, free of charge. Owner notification letters were mailed December 8, 2023. Owners may contact BMW customer service at 1-800-525-7417.
Published by model year, not by VIN — may not apply to this vehicle, or may already have been done. Confirm with a dealer.
The airbag control module (ACSM) may be defective, potentially preventing the airbags from deploying in the event of an accident. This increases the risk of injury to vehicle occupants. Additionally, the airbag warning light or Check Control message may not activate, leaving the driver unaware of the fault. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The positive battery cable of the starter-generator may not have been manufactured correctly. This could result in a loose electrical connection, leading to excessive contact resistance. The vehicle cannot charge or start. Contact points in the starter-generator could overheat and cause a vehicle fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The cockpit cable harness may be damaged when the microfilter is replaced. This can lead to a short circuit, with smoke build-up resulting in fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The hollow shaft of the servomotor was not welded correctly. The weld may not be able to withstand high braking pressure build-up and may break. In this case, the reduced braking performance requires greater force and the braking distance may increase. In addition, the ABS and DSC brake control systems are not assisted. This increases the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Due to manufacturing problem, the rotation bushing of the steering column's double universal joint can break when the steering wheel is turned hard at the extreme position and when steering without steering assistance with the engine switched off. This can lead to unexpected steering behaviour which can increase the risk of accidents and injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The integrated braking system could be compromised, which could lead to an unexpected failure of the hydraulic braking assistance, thereby requiring greater pressure on the brake pedal. This can result in a longer braking distance, as well as failure of the Anti-lock Braking System (ABS) and the Dynamic Stability Control (DSC), increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The ISOFIX clips welded on the rear seats can be damaged. The child seat can detach from the ISOFIX clips, increasing the risk of injury in the event of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Due to incorrectly produced high-voltage cell modules, the cell terminal and the cell-contact system in the battery are not in contact anymore. When strong electricity is flowing, that may cause the cell to overheat and create a risk of fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Matched on brand and model name — Safety Gate publishes no VIN. Check the production dates, and quote the recall code to a dealer.
The contact's insurer owned a 2024 BMW I5. The contact stated that the insurer received notice of NHTSA Campaign Number: 24V104000 (Electronic Stability Control (ESC), Service Brakes, Hydraulic). The contact stated that while the insurer was parking the vehicle, and the brake was depressed, the vehicle inadvertently accelerated and collided with a store's side wall. The contact stated that, to her knowledge, there were no injuries. The contact added that she did not have notice of a police report or that medical attention was needed at this time. The vehicle was towed to a body shop where it was deemed a total loss. The manufacturer was not notified of the failure. The failure mileage was unknown.
During a red light stop, car took off with a massive acceleration after release of breaks and hit the car standing in front of it, causing a significant damage to the front of the car. None of the accident prevention systems, emergency breaks were triggered or activated. Car is equipped with accident record system for 30 seconds before and after an impact, nothing was recorded. Manufacturer promised to investigate but has been more than a week but no one arrived to the collision center yet.
On May 3, 2026, while operating my 2024 BMW i5 on public roads, the vehicle suffered a sudden and complete loss of power steering with no prior warning. I could not turn the steering wheel at a stop. The instrument cluster simultaneously displayed: "Vehicle may roll. Brake manually," "Drive carefully. Changed steering effort," "Drive carefully. Chassis stabilization," and "Parking assistance malfunction." Auto Hold and the electronic parking brake's hold function were disabled, requiring manual brake application to prevent rollaway. Mileage at incident: approximately 21,344 miles. The simultaneous failure of Electric Power Steering, Dynamic Stability Control, and the Electronic Parking Brake while the vehicle was in motion in traffic created an immediate safety hazard. No crash or injury occurred, but a recurrence at highway speed, on a wet road, or during an evasive maneuver could foreseeably cause loss of vehicle control, crash, injury, or death. The vehicle was taken to an authorized BMW dealer. The technician stated this failure is a known issue following a recent vehicle software update, that BMW has no repair available, and that the only action taken was to power-cycle the vehicle and clear stored fault codes. No software remedy, parts replacement, or TSB was provided. I was given no assurance the failure will not recur and no timeline for a fix. To my knowledge, no recall has been issued for this defect on the i5 platform. I request that NHTSA evaluate the scope of this issue across the i5 fleet and determine whether a defect investigation or recall is warranted.
While driving under normal conditions at roadway speed, the panoramic sunroof glass suddenly failed with a loud explosive sound. There was no observed impact, no debris strike, and no prior damage to the glass. The failure resulted in a large central blowout with shattered glass and fragments displaced outward from the vehicle. The failed component is the panoramic sunroof glass panel, which remains available for inspection. This incident created a safety risk due to the sudden explosive event while the vehicle was in motion, which could startle the driver and nearby motorists. At the time of the failure, the interior fabric sunshade was closed, which prevented glass from entering the passenger compartment. Had the shade been open, shattered glass would have fallen into the vehicle and could have caused injury to occupants. There were no warning lights, messages, or prior symptoms before the failure.
While merging onto [XXX] from an on-ramp in [XXX] , I received a dashboard warning stating “Brake system and chassis stabilization – braking may require additional force.” This occurred during active acceleration and merging into highway traffic. At the time of the warning, I experienced reduced confidence in braking performance and increased concern about the vehicle’s ability to stop safely under normal conditions. The situation created a potential safety risk, as I was entering high-speed traffic and required predictable braking capability to adjust to surrounding vehicles. There were no prior warning messages or symptoms before this event. The issue appeared suddenly while driving. After the warning appeared, I drove cautiously and reduced speed, avoiding heavy braking as advised by the system message. I proceeded directly to a nearby dealership and left the vehicle for inspection. The vehicle is currently awaiting diagnosis by an authorized service center. The issue has not yet been confirmed or reproduced by the dealer at the time of this report. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
The vehicle listed has an unfixable defect (water valve/coolant issue) that creates a safety hazard in an electric vehicle, BMW, the manufacturer has failed to provide a remedy within a reasonable timreframe. AC Coolant valve and high voltage battery are part of the same loop which make this vehicle a safety hazard. The No fix as of today. Authorized BMW dealer feedback: ROAD TESTED WITH CUSTOMER AND HEARD NOISE CUSTOMER IS CONCERNED ABOUT. CLICKING NOISE COMING FROM A WATER VALVE LOCATED UNDER THE HOOD DURING ACTIVATION. TEST DROVE VEHICLE WITH BMW TSE, NO CURRENT FIX AVAILABLE.
Battery tempature warning-Constant banging sound while driving. Know EV defect per BMW, No fix in place.
While driving in heavy highway traffic at approximately 5–10 mph, the vehicle suddenly displayed a red warning message and symbol in the driver’s gauge cluster indicating the car was shutting down. About 15–20 seconds later, propulsion was completely lost, although power steering and braking remained available. I attempted to change gears and restart the car by turning it on and off, but nothing worked. I activated the hazard lights since the car was stopped in traffic and posed a danger to surrounding vehicles. Because the vehicle would not respond, I opened and closed the driver’s door and then attempted to restart. At that point, the vehicle restarted, and I was able to continue driving. Out of caution, I remained in the slow lane for the rest of the trip home in case the problem occurred again. The incident created a serious safety risk in the middle of highway traffic. The failure matches the description in BMW’s recent recall (25V395) involving electric drive motor software that can erroneously shut down the high-voltage system after displaying a red warning. However, the manufacturer’s recall lookup currently does not show my vehicle as included. This issue has not yet been reproduced or confirmed by a dealer or service center. I will be contacting them this morning and reporting the issue to them and probably taking it in for inspection.
Make extreme high fan noise during and after super fast charging sessions (Electrify America), overheating issues, unlike all other Evs that do not. Constant clunking sound during and after departing from sessions. Periodic banging sound when parked. Sounds can be observed inside and outside of vehicle. Signs of defect and overheating, safety concerns not addressed by purchasing dealer and manufacture BMW NA. I have video recordings of the issue, and have taking it to two separate BMW dealers no resolution and can not have my kids in the car due to safety concerns.
While reversing my 2024 BMW i5, the main infotainment display repeatedly blacks out for 3–5 seconds, eliminating the rear-view camera image. The blackout occurs without warning, roughly once every 25-30 reverse maneuvers, leaving zero rearward visibility and forcing hard braking to avoid pedestrians and fixed objects. Component/system: Central Information Display / rear-view camera feed (BMW head unit). The original head unit was replaced by the dealer on 07/15/2025 after BMW opened TSARA case 4211001. The removed head unit is in the dealer’s possession and the vehicle is available for inspection. Safety risk: Loss of the only rear-vision aid on this vehicle during backing makes collision with people or property likely. I have had to stop abruptly multiple times to avoid hitting pedestrians in parking lots. Dealer/manufacturer involvement: • First visit: 03/2025 — dealer “unable to replicate,” no repair performed. • Second visit: 07/09–07/15/2025 — dealer replaced head unit; problem persists. The dealer refused to open a PUMA escalation on the first visit but did open TSARA on the second. Warning lamps/messages: None. Blackout is sudden and without any fault codes visible to the driver. Reproduction: Intermittent; has recurred after parts replacement. Incident dates, times, and durations have been logged by the owner. Availability for inspection: Vehicle and dealership service records—including TSARA log—are available upon request. Hopefully, my issue is resolved. I will endeavor to update NHTSA if the issue persists further.
I was driving east bound on [XXX] near the [XXX] exit and using the fully automated driving (where I am watching the road to take over if necessary but the vehicle was maintaining speed and steering) I received the following errors: (I symbol error) Reduced driver assistance, (triangle error) Forward Collision Mitigation, (triangle error) Assisted Driving, (I symbol) Lane Change Assistant. Directly after receiving these errors the steering wheel was stuck at center and required an extreme amount of effort to turn the wheel in any direction. At first I thought it was because the automated system was still engaged but I tried to turn it off and nothing happened. At this point I am getting a little scared as the vehicle is responding to my pedal input but the steering wheel will not release properly. I tried calling the BMW Assist people and they told me to call roadside assistance which would not have helped in my opinion so I told them I didn't want to be transferred over there. I decided to drive the rest of the way home as it was mostly straight getting there. I was concerned that I would have no evidence of this happening so I took a video of what was happening while still on the freeway and recorded my driving for evidence if needed. I was able to exit the highway with extreme difficulty in turning the steering wheel to the point that I was worried I wouldn't be able to capture it on my recording because I thought I might need to use both hands due to the extreme resistance the vehicle was causing. The vehicle finally released the steering wheel so I could drive normally once I came to a complete stop at [XXX] (the exit went into a roundabout and there was no oncoming traffic so I did not stop directly off the highway). I have informed both BMW Northwest (the dealer I purchased from) and BMW USA of this issue and am currently awaiting a response from BMW USA. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
I am writing to formally address concerns regarding the recall on my vehicle and its impact on my ownership experience. 1.Recall Disclosure: According to your records, the recall on my vehicle was issued on 2/12/24. However, I purchased (or leased) the vehicle on 7/21/24 from an authorized dealership. At the time of sale, I was not informed of any open recall, nor was it disclosed by the dealership. According to them, there was no stop sale issued for the vehicle. If I had been made aware of the recall, it could have influenced my decision to proceed with the purchase/lease. 2.Ongoing Impact: This unresolved recall has significantly affected my ability to transfer the lease to a qualified individual, creating financial difficulties. Despite nearly a year since the recall’s issue date, my vehicle has not exhibited any signs or warnings related to the recall. This lack of resolution is now directly impacting my personal finances. Requested Resolution: I kindly request the following: •Confirmation of the exact date my vehicle was added to the recall list and whether a stop sale order was issued. •An immediate update on the recall’s resolution timeline. •Compensation or financial assistance for the inconvenience caused by this prolonged delay. I believe this matter warrants urgent attention, as the lack of disclosure and delay in resolving the recall has created unnecessary financial and logistical burdens. Thank you for addressing this issue promptly. I look forward to your response.
The contact owns a 2024 BMW I5. The contact received notification of NHTSA Campaign Number: 24V104000 (ELECTRONIC STABILITY CONTROL (ESC), SERVICE BRAKES, HYDRAULIC); however, the part to do the recall repair was unavailable. The local dealer was contacted, and it was confirmed that the part was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.
The contact owns a 2024 BMW I5. The contact received notification of NHTSA Campaign Number: 24V104000 (ELECTRONIC STABILITY CONTROL (ESC), SERVICE BRAKES, HYDRAULIC); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.
The contact owns a 2024 BMW i5. The contact received notification of NHTSA Campaign Number: 24V104000 (Electronic Stability Control (ESC), Service Brakes, Hydraulic). The contact stated that when the vehicle was started, the "Driver Restraint System Malfunction" message was displayed. The vehicle was not diagnosed or repaired. The failure mileage was approximately 9,000. The VIN tool confirms that parts are not available.
Filed by owners of this model year and unverified by NHTSA — one person’s account, not an established fact.