3 richiami e 82 segnalazioni di proprietari registrati per questo anno modello.
Questa pagina descrive il modello. Per sapere come è equipaggiata una singola auto e se il suo identificativo è valido, decodifica il VIN.
Decodifica un VINQuasi tutto questo riguarda l’anno modello, non la singola auto. Nulla qui può dirti chilometraggio, incidenti o proprietà di questo veicolo: nessun identificativo li codifica.
TL* THE CONTACT OWNED A 2011 LAND ROVER RANGE ROVER SPORT. THE CONTACT STATED THAT WHILE THE VEHICLE WAS EITHER IN PARK OR IN DRIVE, THE RPM'S WOULD REV WITHOUT WARNING. DUE TO THE FAILURE, THE VEHICLE WOULD LUNGE FORWARD WHILE IN DRIVE. THE CONTACT STATED THAT AFTER PLACING THE VEHICLE INTO REVERSE, SHE PLACED THE VEHICLE INTO DRIVE AND LIGHTLY DEPRESSED THE ACCELERATOR PEDAL; THE VEHICLE THEN LUNGED FORWARD INDEPENDENTLY WITHOUT WARNING CAUSING THE VEHICLE TO DRIVE OVER A 4 FEET WALL AND THEN COLLIDED INTO ANOTHER VEHICLE. THE AIR BAGS DID NOT DEPLOY UPON IMPACT. THE CONTACT WAS TRANSPORTED FROM THE SCENE OF AN ACCIDENT TO A LOCAL HOSPITAL WHERE SHE WAS TREATED FOR A BROKEN BACK. THE OTHER DRIVER REPORTED NO INJURIES. A POLICE REPORT WAS FILED. THE VEHICLE WAS INITIALLY TOWED FROM THE SCENE OF ACCIDENT TO AN INDEPENDENT COLLISION CENTER. THE CONTACT'S INSURANCE COMPANY THEN TOWED THE VEHICLE TO ANOTHER INDEPENDENT COLLISION CENTER WHERE THEY DEEMED THE VEHICLE TOTALED. THE DEALER NOR THE MANUFACTURER HAD BEEN NOTIFIED OF THE FAILURE. THE FAILURE MILEAGE WAS APPROXIMATELY 162,000. *LN*JB
WHILE ATTEMPTING TO CHANGE A FLAT TIRE USING THE FACTORY SUPPLIED VEHICLE JACK, THE JACK FELL OVER AND CAUSED THE VEHICLE TO FALL, PINNING MY HAND IN BETWEEN THE SPARE TIRE AND THE REAR LEFT FENDER. THE VEHICLE WAS STATIONARY AT THE TIME WITH THE EMERGENCY BRAKE ENGAGED. MY HAND WAS PINNED FOR ABOUT 3-5 MINUTES BEFORE MY SON AND A GOOD SAMARITAN WERE ABLE TO LIFT THE VEHICLE OFF OF MY HAND. I LATER HAD X-RAYS DONE, WHICH WERE NEGATIVE. MY HAND WAS CUT AND BRUISED, SO I DID HAVE TO GET A TETANUS SHOT.
TL* THE CONTACT OWNS A 2011 LAND ROVER RANGE ROVER SPORT (N/A). WHILE THE CONTACT WAS AT A COMPLETE STOP, HE NOTICED SMOKE AND A STRONG BURNING ODOR. THE CONTACT INSPECTED UNDERNEATH THE HOOD WITH THE GEAR PLACED IN PARK AND THE ENGINE IN OPERATION. THERE WERE SMALL FLAMES ERUPTING FROM THE BOTTOM OF THE ENGINE. THE ENGINE WAS TURNED OFF IMMEDIATELY AND THE FLAMES WERE NO LONGER VISIBLE. THERE WAS NO PERSONAL INJURY. THE VEHICLE WAS TOWED TO AN AUTHORIZED DEALER WHO WAS UNABLE TO DETERMINE THE CAUSE OF FAILURE. THE MANUFACTURER WAS MADE AWARE OF THE PROBLEM. THE APPROXIMATE FAILURE MILEAGE WAS 6,200. THE VIN WAS UNAVAILABLE.
I WAS DRIVING ON THE HIGHWAY AT 65 MILES PER HOUR AND ALL OF A SUDDEN THE REAR ROOF SPOILER FLEW OFF AND HIT THE CAR BEHIND ME. AFTER DOING SOME RESEARCH I FOUND THIS PROBLEM TO BE COMMON. I WAS SURPRISED TO SEE THAT THERE WAS NO RECAL FOR IT AS IT IS A VERY SERIOUS HAZARD TO ALL DRIVERS NEAR WHEN IT HAPPENS. IF THE WEATHER WAS BAD IT COULD HAVE CAUSED A DEADLY ACCIDENT.
My vehicle overheated due to a cracked rear engine coolant pipe. The vehicle is out of warranty and has been inoperable since August 2025 due to repair cost.
My 2011 Range Rover Sport HSE experienced a severe fuse box failure. Fuses F15, F18, and F20 melted, causing wiring damage and disabling multiple systems. This failure appears to be due to a design or manufacturing defect and poses a serious fire hazard, putting the vehicle and occupants at risk. Upon research, it appears that almost every Range Rover Sport (LR3/320) from 2010–2013 suffers from this issue, indicating a widespread, systemic problem rather than an isolated incident. Request: I formally request that Land Rover and/or NHTSA investigate this safety defect and consider issuing a recall for all affected vehicles immediately. I can provide photographic evidence of the damaged fuse box if needed. Sincerely, [XXX] Phone: [XXX] Email: [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
The fuel tank strap, also known as a fuel tank heat shield, protects the gas tank from debris during driving and off-road use. The original part number is WFN500021 which replaces WFI500053. Due to the metal chosen to make this shield, and the materials of other parts around it, it suffers from galvanic corrosion. As the tank shield starts to rust, that causes rust in other areas to start as well. The shield on my vehicle has probably about 30-40% of its original life left, and I do fear it falling out at some point and possibly the fuel tank going with it as the mounting points for the fuel tank may be corroded along with the tank strap.
The contact owns a 2011 Land Rover Range Rover Sport. The contact stated that while driving at an undisclosed speed, the brake pedal was depressed; however, the vehicle failed to stop as intended. In addition, the low brake fluid warning light was illuminated. The contact stated that the brake pedal was dressed to the floorboard and then pumped several times before the vehicle stopped as needed. The vehicle was taken to an independent mechanic, where it was diagnosed with corrosion to the brake lines. The contact was informed that the brake lines needed to be replaced. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 110,000.
The contact owns a 2011 Land Rover Range Rover Sport. The contact stated that while driving at an undisclosed speed, the front cover on the spoiler detached and flew off the vehicle. The contact became aware that the spoiler cover had detached after arriving at the destination and parking the vehicle. The contact received notification of NHTSA Campaign Number: 20V623000 (Structure). The dealer was made aware of the failure and the open recall; however, the contact was informed that the contact had to pay for the repair. The contact was informed that the recall was old. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The manufacturer was not made aware of the failure. The failure mileage was approximately 135,000.
I was on the highway and the rear spoiler over the back window flew off with the camera installed in the spoiler. The rear camera no longer works as a result of the spoiler flying off the vehicle. I contacted Land Rover of Brooklyn and was informed that they will not make the repair or honor the recall.
Smell gasoline and gasoline on ground. Recall exists for fuel tank but informed my model is not covered but the flange must be damaged as car is currently leaking gas. Car is at Range Rover dealership who says not covered but their is an existing safety recall for my 2011 Range Rover Sports
I purchased this vehicle on [XXX] The vehicle was delivered to me on January 15th. This incident occurred [XXX]. The Engine system failed and is available for inspection. The engine failed and began smoking profusely which inhabited my ability to see as well as other drivers within distance, which put all drivers and passengers at risk. The problem has been confirmed by an independent service center. The vehicle was inspected by a NYS certified mechanic. The check engine light came one prior to the failure and was noticed 2 days after purchasing the vehicle. Which is when this incident occurred. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
The car vibrates a lot. I bought this car 2 months ago and it's my first Land Rover. I loved the car. I want to use it to cross the United States and then take it to Europe. This year I want to do something different because I lost a son at the beginning of the year. I really need the car. I want to cross all of the United States by car. I need the car to be safe.
Hello My car car is the same year as the NHTSA Campaign Number: 20V623000 recall and my spoiler has started separating but am being told from Land Rover that my VIN isn’t in the racall even though it’s that year and has that issue will not do anything about it.
The contact owns a 2011 Land Rover Range Rover Sport. The contact stated that the vehicle was leaking fuel. The brake, fuel, and check engine warning lights were illuminated. The vehicle was towed to the local dealer, where it was diagnosed that the fuel tank flange needed to be replaced. The vehicle was repaired, but the failure recurred. The dealer stated that fuel was leaking in the front of vehicle near the engine. The contact stated that the failure was related to NHTSA Campaign Number 21V635000 (Fuel System, Gasoline). The manufacturer was contacted, and the contact was informed that there was no warranty coverage on the vehicle for the failure. The failure mileage was approximately 170,000.
Presentate dai proprietari di questo anno modello e non verificate da NHTSA: il racconto di una persona, non un fatto accertato.
Corrosion of the airbag connector may increase electrical resistance, which could prevent the driver airbag from deploying correctly in the event of an accident. This increases the risk of injury. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The driver airbag connectors in the steering column has shown that they may corrode. Over time, the airbag might not deploy as intended and therefore could increase the risk of injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the driver and front passenger airbags may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The idler pulley on the front-end accessory drive (FEAD) belt may over-rotate due to high torsional stress and collide with the oil temperature and pressure sensor. This could damage the sensor and cause an oil leak, creating a slipping hazard for other road users, particularly two-wheeled vehicles. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
A defective module has been installed in the high-voltage battery, which may cause it to overheat and lead to a fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The middle seatbelt buckle in the second row of seats may have been incorrectly produced. An incorrectly positioned inner cable can lock the belt tongue and prevent correct locking. In the event of an accident, an improperly locked seatbelt buckle can increase the risk of injury. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Cathode damage during production may accelerate battery ageing and increase the risk of fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The passenger airbag module may tear during deployment as a result of improper folding during the airbag assembly process. In case the airbag is torn, it will not provide adequate protection to occupants and may increase the risk of injury in a crash. Hot gases could escape, causing burns to occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Due to brackets connecting the engine-mounted oil cooler lines not being properly screwed into their threads, the oil cooler hose may become loose or detach, causing engine oil to spill onto the road. This creates slippery sections, increasing the risk of accidents and injuries, especially for two-wheeled vehicles. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The rear cradle may have cracks that can cause the rear wheels to partially detach, creating a risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The plastic used for the oil filter housing in some petrol and diesel engines can crack over time. This can cause oil leaks onto the engine and road. Leaked oil can ignite upon contact with hot engine parts, increasing the risk of a fire. Moreover, it can also create slippery sections, increasing the risk of accidents and injuries especially for two-wheeled vehicles. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Water can infiltrate the rear lamps, leading them to stop working, increasing the risk of rear-end collision accidents and injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Abbinati per marca e nome del modello: Safety Gate non pubblica il VIN. Controlla le date di produzione e cita il codice del richiamo al concessionario.
Jaguar Land Rover North America, LLC (Land Rover) is recalling certain 2011-2012 Land Rover Range Rover vehicles, originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Unless included in "Zone B" above, Land Rover is recalling certain 2010-2012 Land Rover Range Rover vehicles, originally sold, or ever registered, in Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C." These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Rimedio: Land Rover will notify owners, and dealers will replace the front passenger air bag assembly, free of charge. The recall began June 27, 2018. Owners may contact Land Rover customer service at 1-800-637-6837. Land Rover's number for this recall is P084.
Jaguar Land Rover North America, LLC (Land Rover) is recalling certain model year 2007-2011 Land Rover Range Rover vehicles originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Land Rover is recalling certain model year 2007-2008 Land Rover Range Rover vehicles, originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Vehicles not originally sold or ever registered in either Zones A or B are not subject to this safety recall. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Rimedio: Land Rover will notify owners, and dealers will replace the passenger frontal air bag assemblies, free of charge. The recall began March 2017. Owners may contact Land Rover customer service at 1-800-637-6837. Land Rover's number for this recall is P081.
Jaguar Land Rover North America, LLC (Land Rover) is recalling certain model year 2006-2012 Land Rover Range Rover vehicles manufactured April 15, 2005, to September 4, 2012. One or both of the flexible front brake hoses may rupture causing loss of brake fluid.
Rimedio: Land Rover will notify owners, and dealers will replace the left and right front brake hoses, free of charge. The recall began on July 28, 2015. Owners may contact Land Rover customer service at 1-800-637-6837. Land Rover's number for this recall is P054.
Pubblicati per anno modello, non per VIN: potrebbero non riguardare questo veicolo o essere già stati eseguiti. Verifica con un concessionario.