2 richiami e 280 segnalazioni di proprietari registrati per questo anno modello.
Questa pagina descrive il modello. Per sapere come è equipaggiata una singola auto e se il suo identificativo è valido, decodifica il VIN.
Decodifica un VINQuasi tutto questo riguarda l’anno modello, non la singola auto. Nulla qui può dirti chilometraggio, incidenti o proprietà di questo veicolo: nessun identificativo li codifica.
TL*THE CONTACT OWNS A 2006 BMW 525I. WHILE DRIVING APPROXIMATELY 10 MPH, THE CONTACT'S WIFE BEGAN TO FEEL DIZZY. THE NEXT THING SHE REMEMBERED IS SMOKE APPEARING UNDER THE HOOD AND SHE REAR ENDED ANOTHER VEHICLE. THE AIR BAGS FAILED TO DEPLOY. THE CONTACT WAS INJURED AND HAD TO BE TRANSPORTED TO THE HOSPITAL. THE VEHICLE SUSTAINED DAMAGE TO THE FRONT END. A POLICE REPORT WAS FILED. THERE WERE NO AIR BAG RECALLS, BUT THERE IS AN OPEN INVESTIGATION REGARDING THE AIR BAGS. THE CURRENT AND FAILURE MILEAGES WERE 14,500.
When I switch on my driver seat for the heated seat it became so hot that the coils burned through my seat and make two round burn holes in the seat and burned my leg
MY HEATED SEAT CAUGHT ON FIRE AND BURNED ME AND MY COAT. I VERY RARELY USED IT AT ALL. I STARTED USING IT AND IT WAS PROBABLY THE 10TH TIME I USED IT WHEN IT OCCURRED.
MY HEATED SEAT CATCHED ON FIRE. DRIVER SIDE SEAT LEFT SIDE REAR. I GOT BURNED AS I WAS DRIVING ON A PARKING LOT. I REALIZED THAT MY PANTS HAVE A WHOLE AS WELL AS OF THE SEAT
MY DRIVERS SIDE SEAT ( CUSHION) CAUGHT ON FIRE WHEN I TURNED ON THE HEATED SEATS. I FIRST SMELLED A BURNING / PLASTIC SMELL. THEN I FELT MY GLUTES AND HAMSTRING GETTING WARM. I LOOKED DOWN ( I WAS DRIVING) AND SAW AN ORANGE EMBER ON THE SEAT. I PULLED OVER AS SOON AS I COULD, HOT OUT OF THE CAR, AND SAW THAT THE SEAT WAS ACTUALLY BURNING. LUCKILY I HAD A BOTTLE OF WATER IN THE CAR AND PUT OUT THE FLAME AND TURNED OFF THE SEAT. I CALLED THE DEALER- GOT A QUOTE TO REPAIR. BMW WILL NOT TAKE RESPONSIBILITY FOR THIS. I HAVE A SMALL BURN ON MY LEG, AND A GOOD SIZE HOLE IN THE SEAT. I LIKE MY HEATED SEATS LIVING IN THE NORTHEAST DURING WINTER MONTHS. VERY DISAPPOINTED THAT BMW REFUSES TO ADDRESS THIS DANGEROUS ISSUE.
STARTED X5 UP AND TURNED ON DRIVER 'S SEAT WARMER. LET CAR WARM UP FOR 5 MINUTES AND COMMENCED TO DRIVE AWAY. ONE MINUTE DOWN THE ROAD I SMELL SMOKE LIKE AN ELECTRICAL FIRE. I FEEL MY LEFT HIP GETTING HOT AT THE SAME TIME. I STOP CAR AND LOOK DOWN AND SEE A DULL RED GLOW FROM THE SEAT. IMMEDIATELY TURN OFF HEATER AND GET OUT OF CAR. THE DRIVER SEAT WARMER HAD SHORTED AND BURNED A HOLE THROUGH THE LEATHER SEAT ALONG THE LEFT SIDE OF THE SEAT. HOW HOT WAS IT! MY PANTS HAD BEEN BURNT AND HAD A SMALL RED MARK ON MY SKIN. THINK GOODNESS I WAS NOT SEVERELY BURNED DUE TO THE AREA OF MY PANTS THAT WAS BURNT WAS ALSO THE LEFT BACK POCKET AREA SO THE INTERIOR POCKET FABRIC HELP PROTECT ME. WOW! WILL BMW FIX THIS????? *TR
TL* THE CONTACT OWNS A 2006 BMW M5. WHILE DRIVING BETWEEN 35-40 MPH THE VEHICLE CAUGHT ON FIRE. THE VEHICLE HAD A HISTORY OF ELECTRICAL PROBLEMS SINCE THE DAY OF PURCHASE. DURING THE FIRE, THE VEHICLE LOST THE ABILITY TO BRAKE. HE HAD TO USE THE EMERGENCY BRAKE TO STOP THE VEHICLE. THE FIRE DEPARTMENT EXTINGUISHED THE FLAMES. THE VEHICLE WAS COMPLETELY DESTROYED. HE SUFFERED MINOR BURNS ON HIS HANDS. THE FAILURE MILEAGE WAS 40,000.
TL*THE CONTACT OWNS A 2006 BMW X5. THE CONTACT STATED THAT THE ELECTRIC SEAT HEATER ON THE DRIVER'S SIDE CAUGHT FIRE. WHILE AT A STOP LIGHT, HE NOTICED THAT THE SEAT WAS SMOKING AND HIS LEG WAS BURNED. THE SEAT HEATER WAS ACTIVATED PRIOR TO NOTICING THE FAILURE. HE TOOK THE VEHICLE TO THE DEALER, WHERE IT CURRENTLY REMAINS. THE MANUFACTURER STATED THAT THEY WERE AWARE OF THE ISSUE; HOWEVER, THE FAILURE WAS A RESULT OF THE RISK OF HAVING SEAT HEATERS. THEY ALSO STATED THAT THEY WOULD REPAIR THE VEHICLE FOR FREE. THE CURRENT AND FAILURE MILEAGES WERE APPROXIMATELY 27,000.
TL*THE CONTACT OWNS A 2006 BMW X5. WHILE DRIVING 3 MPH, ANOTHER VEHICLE CRASHED INTO THE FRONT SIDE QUARTER PANEL OF THE CONTACT'S VEHICLE. THE OTHER VEHICLE WAS DRIVING APPROXIMATELY 20 MPH. THE AIR BAGS FAILED TO DEPLOY. THE VEHICLE CAME EQUIPPED WITH SIDE AIR BAGS. THERE WERE NO WARNING INDICATOR LIGHTS PRESENT. A POLICE REPORT WAS FILED. THE VEHICLE WAS TOWED FROM THE SCENE AND HAS NOT YET BEEN INSPECTED. THE DRIVER WAS TAKEN TO THE EMERGENCY ROOM IN AN AMBULANCE BECAUSE HER HEAD HIT THE DOOR WINDOW. THE CURRENT AND FAILURE MILEAGES WERE 19,000.
I WAS DRIVING A NEW BMW M5 IN CHICAGO ON LOWER LAKE SHORE DRIVE (THE BRIDGE OVER THE CHICAGO RIVER.) AT APPROXIMATLY 30-35 MILES/HOUR THE CAR WAS NOT CONTROLLABLE AND THIS RESULTED IN TO A MAJOR CRASH WITH SIGNIFICANT INJURY, SEVERAL DEVICES WERE NOT FUNCTIONING PROPERLY INCLUDING THE DEPLOYMENT OF THE AIR-BAGS. I HAVE BEEN DRIVING FOR OVER THIRTY YEARS AND DURING THIS TIME I DID NOT EXPERIENCE EVEN A MINOR ACCIDENT NOR DID I EVER RECEIVE A TICKET FOR A TRAFFIC VIOLATION. *JB
COMPUTER LOCKED KEY, ALL LIGHTS INSIDE CAR AND OUTSIDE FLICKERED OUT OF CONTROL, THEN 2 WEEKS LATER BRAKE DID NOT ENGAGE WHILE TRYING TO STOP AND THE VEHICLE CRASHED INTO A POLE. *JB
THE DRIVER SIDE HEATED SEAT OVERHEATS AND BECOMES TOO HOT TO TOUCH. I HAVE EXPERIENCE DISCOLORATION IN SOME OF MY CLOTHING DUE TO THE EXCESSIVE HEAT, AND I EXPERIENCED A SLIGHT BURNED ON MY THIGH WHEN THE HEATED SEAT IS TURNED ON. THE ISSUE OCCURS WHILE THE CAR IS IN MOTION OR STATIONARY. THE LEATHER MOST AFFECTED BY THE HEATED SEAT MALFUNCTION IS THINNING. I HAVE CONTACTED THE LOCAL BMW DEALERSHIP TWICE ABOUT THE ISSUES, AND I HAVE BEEN IGNORED WHEN I REQUESTED A QUOTE ON THE REPAIR AND WHY THE SAFETY ISSUE HAS NOT BEEN ADDRESSED.
WHILE DRIVING I TURNED ON MY HEATED SEATS AND ABOUT 15 MINUTES LATER MY DRIVERS SIDE SEAT BECAME VERY HOT AND STARTED TO BURN ME. I PULLED OVER ABRUPTLY, JUMPED OUT OF MY CAR AND NOTICED THAT MY PANTS WAS DISCOLORED/BURNED AND MY SEAT WAS BURNED AND HAD A BURN HOLE (ABOUT 3.5 INCHES) IN IT., THE CAR HAD A PLASTIC TYPE BURN SMELL IN IT. I AM TERRIFIED TO TURN ON THE HEATED SEATS AGAIN.
DRIVERS SIDE HEATED SEAT BURNED THROUGH LEATHER SEATS ON RIGHT SIDE OF SEAT AT RIB CAGE. SLIGHTLY BURNED DRIVER. HAD A ELECTRICAL BURNING SMELL. LEFT ABOUT A 6 INCH BURN LINE IN THE SEAT. VERY UNATTRACTIVE! *TR
WE OWN A 2006 BMW X5. WITHIN THE LAST WEEK WHEN THE DRIVER'S SEAT WARMER WAS TURNED ON, THE LEFT SIDE OF HE SEAT HEATED UP ALMOST INSTANTLY, AND BURNS THE LEFT THIGH AND BUTTOCKS AREA OF THE DRIVER. MY HUSBAND RECEIVED A 3 INCH BURN ON MAY 15,2010. FIVE DAYS PRIOR TO THIS I WAS AWARE THAT AN AREA OF THE DRIVER'S SEAT WAS BURNING ME, AND I IMMEDIATELY TURNED THE WARMER OFF. THE WARRANTY EXPIRED ON OUR CAR IN DECEMBER. *TR
Presentate dai proprietari di questo anno modello e non verificate da NHTSA: il racconto di una persona, non un fatto accertato.
BMW of North America LLC (BMW) is recalling certain model year 2006 325i, 325xi, 330i, 330xi sedans and 325xi sports wagons, model year 2007 328i, 328xi, 335i, 335xi sedans and 328i and 328xi sports wagons, model year 2006-2007 525i, 525xi, 530i, 530xi, 550i sedans and 530xi sports wagons, model year 2006 760i sedans, model year 2006-2007 750i, 750Li, and 760Li sedans, and model year 2006 X5 sports activity vehicles, equipped with certain seat types. The front passenger seat occupant detection mat that determines if and how the passenger frontal air bag should deploy in a crash may fatigue and develop cracks which could lead to a system failure.
Rimedio: BMW will notify owners with an interim notification letter in January 2014 since parts are not currently available. When parts are available, BMW sent a second letter in August and dealers will repair the occupant detection mat to eliminate the possibility that it may crack, free of charge. Additionally, owners of model year 2006-2007 3 Series with standard seats, 5 Series with comfort seats, and Z4 models, will receive an extended warranty on their front passenger seat occupant detection mat. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
CERTAIN PASSENGER VEHICLES MAY HAVE BEEN BUILT WITH AN INCORRECTLY MANUFACTURED AUTOMATIC TRANSMISSION PARKING PAWL GUIDE PLATE.
Rimedio: DEALERS WILL REPAIR AND REPLACE THE AUTOMATIC TRANSMISSION GUIDE PLATE FREE OF CHARGE. THE RECALL BEGAN ON NOVEMBER 30, 2005. OWNERS MAY CONTACT BMW AT 1-800-332-4269.
Pubblicati per anno modello, non per VIN: potrebbero non riguardare questo veicolo o essere già stati eseguiti. Verifica con un concessionario.
Water may come into contact with the starter relay and gradually cause corrosion. This could affect the electrical connection inside the relay and make the engine difficult to start. It may also result in a short circuit and could cause the starter to overheat leading to a fire when the vehicle is in motion or when it is parked with the ignition off. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The engine starter’s electrical contacts may overheat and cause the vehicle to start improperly. Continued starting attempts can intensify the overheating and ignite surrounding components, potentially leading to a vehicle fire while driving or shortly after parking. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The RSW22 starter with reinforced water tightness (RWT) may experience increased abrasion of the magnetic contact, causing deposits to build up at the lowest point inside the relay. These deposits may increase relay contact resistance, leading to starting failures or short circuits. If a short circuit occurs, either when attempting to start the vehicle or while driving due to vibration-related movement of the deposits, it could cause a thermal event and increase the risk of fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The positive battery cable of the starter-generator may not have been manufactured correctly. This could result in a loose electrical connection, leading to excessive contact resistance. The vehicle cannot charge or start. Contact points in the starter-generator could overheat and cause a vehicle fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The chemical substances in the inflators of the TAKATA PSDI4 airbags may deteriorate over time, particularly in warm, humid climates. This could cause the airbag to rupture with too much force in the event of an accident, which could lead to serious or even fatal injuries in the worst-case scenario. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The failure concerns the RSW22 starter, type RWT (reinforced for watertightness). Increased abrasion of the magnetic contact can lead to the formation of deposits at the lowest point of the relay interior. This in turn can increase the resistance of the relay contact, causing accidental ignition or even short circuits, possibly leading to a thermal reaction and fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The failure concerns the RSW22 starter, type RWT (reinforced for watertightness). Increased abrasion of the magnetic contact can lead to the formation of deposits at the lowest point of the relay interior. This in turn can increase the resistance of the relay contact, causing accidental ignition or even short circuits, possibly leading to a thermal reaction and fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The hollow shaft of the servomotor was not welded correctly. The weld may not be able to withstand high braking pressure build-up and may break. In this case, the reduced braking performance requires greater force and the braking distance may increase. In addition, the ABS and DSC brake control systems are not assisted. This increases the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The software-based overload protection function cannot sufficiently prevent the starter being overloaded in the event of repeated long start-up attempts. The starter may overheat or sparks may be produced as a result of an increased current flow. This increases the risk of a fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The gas generator in knee airbag modules was not properly inserted into the air cushion, resulting in the cushion failing to unfold sufficiently. As a result, it may not be able to deploy correctly in the event of an accident, leading to a reduction in the restraint effect, increasing the risk of injury to the occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
A seam on the inflator housing of the driver airbag may not have been correctly welded. In case of accident, when the airbag is deployed, the inflator can burst, releasing metal parts which could cause injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The stated maximum load specified in the user manual is incorrect. This could cause users to overload the vehicle, potentially leading to damage to the car and an increased risk of accidents and injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The integrated braking system could be compromised, which could lead to an unexpected failure of the hydraulic braking assistance, thereby requiring greater pressure on the brake pedal. This can result in a longer braking distance, as well as failure of the Anti-lock Braking System (ABS) and the Dynamic Stability Control (DSC), increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The dashboard in the affected vehicles may not have been manufactured to the manufacturer specifications. In the event of anaccident, the passenger side airbag may not deploy as intended which could increase the risk of injury to the frontpassenger. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Due to a manufacturing error, the weld seam of the integrated transmission control unit (ITCU) may not have been correctly executed. As a result, transmission oil could leak into the ITCU, causing it to fail. This may lead to transmission seizure, increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Abbinati per marca e nome del modello: Safety Gate non pubblica il VIN. Controlla le date di produzione e cita il codice del richiamo al concessionario.