6 richiami e 29 segnalazioni di proprietari registrati per questo anno modello.
Questa pagina descrive il modello. Per sapere come è equipaggiata una singola auto e se il suo identificativo è valido, decodifica il VIN.
Decodifica un VINQuasi tutto questo riguarda l’anno modello, non la singola auto. Nulla qui può dirti chilometraggio, incidenti o proprietà di questo veicolo: nessun identificativo li codifica.
WHEN STRIKING ANOTHER VEHICLE HEAD-ON AT 20-25 MPH AIR BAGS DID NOT DEPLOY. DEALER HAS BEEN CONTACTED.*AK
PULLED VEHICLE INTO GARAGE AND FRONT, RIGHT SIDE STARTED SMOKING. MY DAUGHTER AND I JUMPED OUT OF THE CAR AND RAN INTO THE HOUSE TO ALERT MY HUSBAND. WITHIN SECONDS, SMOKE FILLED THE GARAGE AND FIRE WAS VISIBLE UNDER FRONT, RIGHT TIRE AND THROUGH HOOD. I CALLED THE 911 AND MY HUSBAND TRIED TO DOUSE THE FLAMES. THIS NOT WORKING, SO MY HUSBAND MADE THE DECISION TO BACK THE CAR OUT OF THE GARAGE, HOWEVER, THE CAR WOULD NOT START. HE QUICKLY MADE THE DECISION TO PUT THE CAR IN NEUTRAL AND PUSHED IT FROM THE DRIVER'S DOOR FRAME TO THE MIDDLE OF THE DRIVEWAY. SECONDS LATER, THE ENTIRE RIGHT SIDE OF THE CAR WAS IN FLAMES. THE FIRE DEPARTMENT ARRIVED AND DOUSED THE FLAMES. THEY ALSO HAD TO CUT OPEN THE HOOD TO ENSURE ALL FLAMES WERE OUT PRIOR TO LEAVING. *TR
VEHICLE HAS HAD INTERMITTENT BRAKE FAILURE AT SLOW SPEEDS. DEALER REPLACED CRACKED MASTER CYLINDER AND REAR ABS SENSOR. THEN, STATED THERE WAS NOTHING WRONG WITH VEHICLE. WHILE DRIVING 20 MPH CONSUMER REARENDED ANOTHER VEHICLE DUE TO BRAKE FAILURE. DAMAGE TO VEHICLE WAS $ 500.00 VEHICLE HAS BEEN AT DEALER SINCE ACCIDENT ON 21 MAY 2001.*AK ON ONE OCCASION, THE SPEEDOMETER QUIT WORKING WHEN THE ABS LIGHT ILLUMINATED, WHILE SLOWING DOWN ON DRY PAVEMENT, VEHICLE STARTED TO JERK FORWARD AND BACK, DEALER REPLACED WHEEL SPEED SENSOR. DRIVERS SIDE SEAT BELT DOES NOT RETRACT. *SLC
INCIDENT OCCURRED ON 3/14/2016 AT THE INTERSECTION OF E LAKE FOREST DR/ MIMOSA WY DURING DRIVING. COMPLETE BRAKE FAILURE DURING DRIVING WHILE TURNING CORNER FROM TIRE WEARING AGAINST PASSENGER FRONT BRAKE LINE. ALMOST CAUSED SERIOUS AUTO ACCIDENT. INQUIRED WITH DEALER WHEN PURCHASING REPLACEMENT PARTS THAT THERE WAS A KNOWN RECALL FOR THIS INCIDENT AND DEALER DID NOT KNOW PROCESS FOR NTSA RECALLS. OWNER PAID FOR REPLACEMENT PARTS AS DEALER/MANUFACTURER WAS UNWILLING TO FIX. CAN PROVIDE RECEIPTS. REPORT RECEIPT DATE: JAN 09, 2003 NHTSA CAMPAIGN NUMBER: 03V001000 COMPONENT(S): SERVICE BRAKES, HYDRAULIC ALL PRODUCTS ASSOCIATED WITH THIS RECALL EXPAND DETAILS CLOSE 10 ASSOCIATED DOCUMENTS EXPAND MANUFACTURER: BAYERISCHE MOTOREN WERKE SUMMARY: ON CERTAIN SPORT UTILITY VEHICLES, IT MAY BE POSSIBLE FOR THE FRONT BRAKE LINE TO SLIP OUT OF THE RETAINING BRACKET LOCATED AT THE FRONT STRUT. THE BRAKE HOSE THAT IS ATTACHED TO THE BRAKE LINE COULD COME IN CONTACT WITH THE TIRE AND BE SUBJECTED TO WEAR AND ABRASION. CONSEQUENCE: THIS COULD INITIALLY CAUSE SOME BRAKE FLUID LEAKAGE, AND EVENTUALLY LEAD TO A SUBSTANTIAL LOSS OF BRAKE FLUID. THERE COULD BE A NOTICEABLE REDUCTION IN BRAKE PERFORMANCE IF A LOSS OF FRONT BRAKE PERFORMANCE OCCURS. REMEDY: DEALERS WILL INSTALL AN ADDITIONAL RETAINING CLIP TO FURTHER SECURE THE BRAKE LINE TO THE FRONT STRUT. ADDITIONALLY, IF INSPECTION OF ANY BRAKE HOSE INDICATES THAT IT HAS EXPERIENCED DAMAGE, THE HOSE WILL BE REPLACED. OWNER NOTIFICATION BEGAN FEBRUARY 14, 2003. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT BMW AT 1-800-831-1117. NOTES: CUSTOMERS CAN ALSO CONTACT THE NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION'S AUTO SAFETY HOTLINE AT 1-888-DASH-2-DOT (1-888-327-4236).
I WAS TURNING INTO A RESTAURANT ( I WAS COMPLETELY STOPPED) AND AS I GOT THE CHANCE TO TAKE THE TURN, IT BECAME EXTREMELY HARD TO TURN THE WHEEL, LUCKILY MY SON WAS SITTING NEXT TO ME AND HE HAD TO MANUALLY HELP ME TO TURN THE CAR. I HIT THE CURB BUT LUCKILY MANAGED TO PULL OUT OF THE STREET AND OUT OF THE WAY OF TRAFFIC. IT WAS A HIGHWAY SO PEOPLE WERE GOING ABOUT 55-60 MPH (I GOT HONKED AT). WE PULLED IN STOPPED AT THE ENTRANCE. WE TURNED OFF THE ENGINE, MY SON WENT OUT TO LOOK AT THE DAMAGE AND IF ANYTHING WAS WRONG WITH THE TIRES. WE BARELY MADE IT TO A PARKING SPOT AS MY SON COULD BARELY TURN IT. PLEASE FIX THIS ISSUE, PRAISE THE LORD NOBODY WAS HURT. *TR
THIS IS NOT THE FIRST TIME. THE RIGHT HAND SIDE, PASSENGER'S FRONT WINDOW FAILED TO OPERATE. THIS IS AN ELECTRICAL SYSTEM COMPONENT. *TR
TL* THE CONTACT OWNS A 2000 BMW X5. WHILE PARKED, THE CONTACT NOTICED THAT THE FRONT DRIVER SIDE SEAT BELT WOULD NOT RETRACT. THE VEHICLE WAS TAKEN TO THE DEALER FOR DIAGNOSTICS. THE TECHNICIANS REPLACED THE SEAT BELT ASSEMBLY FOR THE FRONT DRIVER SIDE SEAT. AFTER SOME TIME, THE FRONT PASSENGER SIDE SEAT BELT FAILED TO RETRACT. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE AND A COMPLAINT WAS FILED. THE MANUFACTURER STATED TO THE CONTACT THAT THE SEAT BELT REPAIR WOULD NOT BE COVERED UNDER WARRANTY DUE TO THE AGE OF THE VEHICLE. THE VEHICLE WAS NOT REPAIRED. THE APPROXIMATE FAILURE MILEAGE WAS 50,000.
TL*THE CONTACT OWNS A 2000 BMW X5. WHILE PARKED, THE CONTACT ATTEMPTED TO EXIT THE VEHICLE USING THE FRONT DRIVER SIDE DOOR BUT THE DOOR WOULD NOT OPEN. THE CONTACT EXITED THE VEHICLE THROUGH ANOTHER DOOR AND NOTICED THE FRONT DRIVER SIDE DOOR ALSO WOULD NOT OPEN FROM THE OUTSIDE. THE VEHICLE WAS NOT TAKEN TO HAVE THE FAILURE DIAGNOSED. THE VEHICLE WAS NOT REPAIRED. THE FAILURE AND CURRENT MILEAGES WERE 76,000. THE VIN WAS UNAVAILABLE.
TL*THE CONTACT OWNS A 2000 BMW X5. THE CONTACT STATED THAT THE FRONT DRIVER AND REAR PASSENGER WINDOWS HAVE FALLEN INSIDE THE DOOR DUE TO A FAULTY REGULATOR. THE CONTACT HAS TAKEN THE VEHICLE TO A DEALER TO HAVE THE DRIVER SIDE WINDOW REPAIRED AND FIVE DAYS AFTER THE REPAIR THE REAR PASSENGER SIDE WINDOW BROKE. THE CONTACT HAS CALLED THE MANUFACTURER AND REQUESTED THAT THEY ASSUME THE COST SINCE THE WARRANTY HAS EXPIRED. THE CONTACT IS CONCERNED THAT A DEFECT INVESTIGATION WAS NOT AVAILABLE FOR HIS YEAR MAKE AND MODEL VEHICLE. THE FAILURE MILEAGE WAS 60,000.
NO REVERSE AND ALSO NO COMMUNICATION TO THE ABS MODULE SO NO ABS. *TR
ON JUNE 3, 2009 I TOOK MY X5 BMW TO CHECKERED FLAG BMW 5225 VIRGINIA BEACH BLVD VIRGINIA BEACH, VIRGINIA 23454 TO HAVE AN INCONSISTENT HESITATION CHECKED. THERE WAS NO CHECK ENGINE OR TRANSMISSION LIGHT ON. THE VEHICLE WAS LEFT WITH THE DEALER FOR 3 DAYS, THE SERVICE MANAGER CALLED ON JUNE 6, 2009 , TOLD MY HUSBAND AND I THAT THE TRANSMISSION WAS COMPLETELY BURNED UP. I TOLD THE SERVICE MANAGER THAT THE X5 HAS A SEAL TRANSMISSION. ACCORDING TO MY SERVICE MANUAL A WARNING LIGHT SHOULD HAD CAME ON PUTTING THE VEHICLE IN TRANSMISSION SAFE MODE INFORMING ME TO TAKE IT TO THE DEALER FOR SERVICE. THIS WOULD PREVENT ANY DAMAGE TO THE TRANSMISSION. HOWEVER NO WARNING LIGHT CAME ON. BASICALLY HE TOLD US THE VEHICLE WAS MADE WITH A DEFECTED TRANSMISSION MODULECONTROL PART. WE TOLD HIM TO FIX THE TRANSMISSION AND THAT IT WASN'T MY FAULT IT WAS DEFECTED. HE REFUSED TO REPAIR IT . *TR
TRANSMISSION FAILURE 2000 BMW X5 4.4 AUTOMOBILE 70,000 MILES. *TR
TL*- WHILE DRIVING THE 2000 BMW X5 AT 40 MPH THE TRANSMISSION DISENGAGED, CAUSING THE RPMS TO RISE RATHER THAN DROPPING BACK INTO GEAR. THE DISENGAGING AND DROPPING BACK INTO GEAR HAPPENED ABOUT 4-8 TIMES WITHIN 10-15 MINUTES. THE CONTACT TOOK VEHICLE TO A EUROPEAN VEHICLE REPAIR FACILITY, AND THEY STATED THAT THE TRANSMISSION WAS COMPLETELY BURNED. THE CONTACT STATED THAT THERE IS NO WAY TO CHECK OR CHANGE THE TRANSMISSION FLUID OTHER THEN REMOVING THE TRANSMISSION FROM THE VEHICLE. THE CONTACT HAS DONE SOME RESEARCH ONLINE ,AND THAT THIS TRANSMISSION PROBLEM SEEMS TO OCCUR AROUND 80,000 MILES. HIS VEHICLE'S FAILURE MILEAGE WAS 82,000 MILES.*AK
DT: THE CONTACT STATED THE WINDSHIELD WIPERS COMPLETELY AND RANDOMLY FAILED TO WORK. THE WINDSHIELD WIPER QUIT FOUR TIMES IN TWO YEARS. THE FIRST TIME THIS HAPPENED THE BMW DEALERSHIP REPLACED THE MOTOR. IT QUIT AGAIN ABOUT SIX MONTHS LATER. SINCE THEN THE DEALER HAS NOT BEEN ABLE TO DUPLICATE THE PROBLEM; MOSTLY BECAUSE OCCURRED RANDOMLY.*AK UPDATED 12/27/05. *JB
WHILE DRIVING AT ANY SPEED DRIVER HEARD A LOUD KNOCKING NOISE COMING FROM THE FRONT. DRIVER WAS UNABLE TO SHIFT INTO REVERSE. VEHICLE WAS TOWED TO A BODY SHOP FOR INSPECTION, AND MECHANIC DETERMINED THAT THE TRANSMISSION NEEDED TO BE REPLACED. *AK
Presentate dai proprietari di questo anno modello e non verificate da NHTSA: il racconto di una persona, non un fatto accertato.
1 richiamo comporta un divieto di circolazione o l’obbligo di sosta all’aperto. Verifica se su questo veicolo l’intervento è già stato eseguito prima di guidarlo o parcheggiarlo.
BMW of North America, LLC (BMW) is recalling certain 2000-2001 X5 vehicles that may be equipped with a sport steering wheel containing a Takata PSDI-4 air bag inflator. The inflator may explode during deployment due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature, and temperature cycling.
Rimedio: Owners are advised not to drive their vehicles until the remedy is complete. Dealers will inspect and replace the driver's front air bag, as necessary, free of charge. Owner notification letters were mailed December 29, 2025. Owners may contact BMW customer service at 1-800-525-7417. Vehicle Identification Numbers (VINs) involved in this recall will be searchable on NHTSA.gov beginning December 23, 2025. This recall expands previous NHTSA recall number 19V015.
ON CERTAIN SPORT UTILITY VEHICLES, IT MAY BE POSSIBLE FOR THE FRONT BRAKE LINE TO SLIP OUT OF THE RETAINING BRACKET LOCATED AT THE FRONT STRUT. THE BRAKE HOSE THAT IS ATTACHED TO THE BRAKE LINE COULD COME IN CONTACT WITH THE TIRE AND BE SUBJECTED TO WEAR AND ABRASION.
Rimedio: DEALERS WILL INSTALL AN ADDITIONAL RETAINING CLIP TO FURTHER SECURE THE BRAKE LINE TO THE FRONT STRUT. ADDITIONALLY, IF INSPECTION OF ANY BRAKE HOSE INDICATES THAT IT HAS EXPERIENCED DAMAGE, THE HOSE WILL BE REPLACED. OWNER NOTIFICATION BEGAN FEBRUARY 14, 2003. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT BMW AT 1-800-831-1117.
ON CERTAIN PASSENGER VEHICLES, DUE TO A MANUFACTURING PROBLEM, THE BRAKE PEDAL ARM PIVOT SHAFT COULD LOOSEN FROM ITS SUPPORT BRACKET.
Rimedio: DEALERS WILL CHECK THE BRAKE PEDAL ARM PIVOT SHAFT FOR PROPER SEATING IN ITS SUPPORT BRACKET. IN ADDITION, A PIN WILL BE INSTALLED TO SECURE THE SHAFT TO THE BRACKET. OWNER NOTIFICATION BEGAN AUGUST 14, 2002. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT BMW AT 1-800-332-4269.
VEHICLE DESCRIPTION: 4.4I SPORT UTILITY VEHICLES. OVER AN EXTENDED PERIOD OF TIME, ABRASION PARTICLES COULD DEPOSIT ON THE ELECTRICAL CONTACTS WITHIN THE SWITCH, CAUSING A DISRUPTION OF THE ELECTRIC CURRENT THROUGH THE CONTACTS. IF THE DISRUPTION OCCURS WHEN THE VEHICLE IS STATIONARY WITH THE TRANSMISSION IN THE NEUTRAL OR PARK POSITIONS, THE TRANSMISSION WILL SWITCH AUTOMATICALLY INTO THE EMERGENCY PROGRAM, WHICH IS DISPLAYED IN THE INSTRUMENT CLUSTER VIA A WARNING LAMP AND A MESSAGE, "TRANS. FAIL-SAFE PROG." IN THIS CASE, THE VEHICLE CAN BE DRIVEN IN LOWER GEARS ONLY WITH LIMITED ENGINE OUTPUT.
Rimedio: DEALERS WILL REPLACE THE TRANSMISSION GEAR POSITION INDICATOR SWITCH. OWNER NOTIFICATION BEGAN AUGUST 14, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT BMW AT 1-800-831-1117.
VEHICLE DESCRIPTION: 4.4I SPORT UTILITY VEHICLES. THERE IS A PLASTIC CARRIER TO WHICH THE OIL FILTER HOUSING IS ATTACHED. OIL SUPPLY AND RETURN LINES ARE ATTACHED TO THE FILTER HOUSING. OVER TIME, THIS CARRIER COULD SAG SLIGHTLY. IF THIS HAPPENS, ONE OF THE OIL LINES, WHICH ARE ARMORED WITH STEEL MESH, COULD COME INTO CONTACT AND CHAFE A STEEL BRAKE LINE LOCATED IMMEDIATELY UNDERNEATH.
Rimedio: DEALERS WILL INSTALL A RUBBER SPACER BELOW THE PLASTIC CARRIER TO PREVENT SAGGING AND SUBSEQUENT CONTACT BETWEEN THE OIL AND BRAKE LINES. BRAKE LINES WHOSE ANTICORROSION LAYER IS FOUND TO BE DAMAGED AS A RESULT OF CONTACT WITH THE OIL LINE WILL BE REPLACED. OWNER NOTIFICATION BEGAN AUGUST 14, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT BMW AT 1-800-831-1117.
VEHICLE DESCRIPTION: SPORT UTILITY VEHICLES. THE LOWER STEERING SHAFT COUPLING INCLUDES A PLASTIC COLLAR WHICH FITS OVER THE LOWER STEERING RACK INPUT SHAFT. THIS COLLAR IS PUSHED DOWN ONTO THE STEERING RACK AND TIGHTENED DURING ASSEMBLY. ON SOME OF THE AFFECTED VEHICLES, THE COLLAR MAY NOT HAVE BEEN PUSHED DOWN FULLY ONTO THE RACK AT THE ASSEMBLY PLANT.
Rimedio: DEALERS WILL INSPECT THE STEERING RACK INPUT SHAFT COLLAR FOR PROPER POSITIONING, AND REPOSITION IS NECESSARY.
Pubblicati per anno modello, non per VIN: potrebbero non riguardare questo veicolo o essere già stati eseguiti. Verifica con un concessionario.
Water may come into contact with the starter relay and gradually cause corrosion. This could affect the electrical connection inside the relay and make the engine difficult to start. It may also result in a short circuit and could cause the starter to overheat leading to a fire when the vehicle is in motion or when it is parked with the ignition off. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The engine starter’s electrical contacts may overheat and cause the vehicle to start improperly. Continued starting attempts can intensify the overheating and ignite surrounding components, potentially leading to a vehicle fire while driving or shortly after parking. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The RSW22 starter with reinforced water tightness (RWT) may experience increased abrasion of the magnetic contact, causing deposits to build up at the lowest point inside the relay. These deposits may increase relay contact resistance, leading to starting failures or short circuits. If a short circuit occurs, either when attempting to start the vehicle or while driving due to vibration-related movement of the deposits, it could cause a thermal event and increase the risk of fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The positive battery cable of the starter-generator may not have been manufactured correctly. This could result in a loose electrical connection, leading to excessive contact resistance. The vehicle cannot charge or start. Contact points in the starter-generator could overheat and cause a vehicle fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The chemical substances in the inflators of the TAKATA PSDI4 airbags may deteriorate over time, particularly in warm, humid climates. This could cause the airbag to rupture with too much force in the event of an accident, which could lead to serious or even fatal injuries in the worst-case scenario. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The failure concerns the RSW22 starter, type RWT (reinforced for watertightness). Increased abrasion of the magnetic contact can lead to the formation of deposits at the lowest point of the relay interior. This in turn can increase the resistance of the relay contact, causing accidental ignition or even short circuits, possibly leading to a thermal reaction and fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The failure concerns the RSW22 starter, type RWT (reinforced for watertightness). Increased abrasion of the magnetic contact can lead to the formation of deposits at the lowest point of the relay interior. This in turn can increase the resistance of the relay contact, causing accidental ignition or even short circuits, possibly leading to a thermal reaction and fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The hollow shaft of the servomotor was not welded correctly. The weld may not be able to withstand high braking pressure build-up and may break. In this case, the reduced braking performance requires greater force and the braking distance may increase. In addition, the ABS and DSC brake control systems are not assisted. This increases the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The software-based overload protection function cannot sufficiently prevent the starter being overloaded in the event of repeated long start-up attempts. The starter may overheat or sparks may be produced as a result of an increased current flow. This increases the risk of a fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The gas generator in knee airbag modules was not properly inserted into the air cushion, resulting in the cushion failing to unfold sufficiently. As a result, it may not be able to deploy correctly in the event of an accident, leading to a reduction in the restraint effect, increasing the risk of injury to the occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
A seam on the inflator housing of the driver airbag may not have been correctly welded. In case of accident, when the airbag is deployed, the inflator can burst, releasing metal parts which could cause injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The stated maximum load specified in the user manual is incorrect. This could cause users to overload the vehicle, potentially leading to damage to the car and an increased risk of accidents and injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The integrated braking system could be compromised, which could lead to an unexpected failure of the hydraulic braking assistance, thereby requiring greater pressure on the brake pedal. This can result in a longer braking distance, as well as failure of the Anti-lock Braking System (ABS) and the Dynamic Stability Control (DSC), increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The dashboard in the affected vehicles may not have been manufactured to the manufacturer specifications. In the event of anaccident, the passenger side airbag may not deploy as intended which could increase the risk of injury to the frontpassenger. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Due to a manufacturing error, the weld seam of the integrated transmission control unit (ITCU) may not have been correctly executed. As a result, transmission oil could leak into the ITCU, causing it to fail. This may lead to transmission seizure, increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Abbinati per marca e nome del modello: Safety Gate non pubblica il VIN. Controlla le date di produzione e cita il codice del richiamo al concessionario.