3 richiami e 88 segnalazioni di proprietari registrati per questo anno modello.
Questa pagina descrive il modello. Per sapere come è equipaggiata una singola auto e se il suo identificativo è valido, decodifica il VIN.
Decodifica un VINQuasi tutto questo riguarda l’anno modello, non la singola auto. Nulla qui può dirti chilometraggio, incidenti o proprietà di questo veicolo: nessun identificativo li codifica.
WHILE ATTEMPTING TO MAKE A RIGHT TURN THE STEERING WHEEL LOCKED AND AT THAT TIME THE BRAKES BECAME UNRESPONSIVE AS WELL. THIS RESULTED IN A MOTOR VEHICLE ACCIDENT AS MY CAR ONLY STOPPED BY HITTING ANOTHER CAR WAITING AT THE OPPOSITE LIGHT. IT CAN BE COMPARED TO SLIDING ON A PATCH OF ICE, BUT THERE IS NO OPTION TO MOVE THE WHEEL TO TRY AND REGAIN CONTROL OF YOUR CAR. I AM VERY THANKFUL THAT I WAS NOT ON THE INTERSTATE WHEN THIS OCCURRED. THERE IS A VERY SERIOUS SAFETY HAZARD AS I HAVE DONE SOME RESEARCH AND FOUND THAT THIS IS A COMMON ISSUE WITH THIS PARTICULAR AUTOMOBILE MAKE.
NONE OF THE AIRBAGS DEPLOYED IN OUR CAR ACCIDENT. WE WERE AT A STAND STILL, OR MOVING VERY SLOWLY AND ANOTHER CAR HIT US IN THE REAR DRIVER SIDE PANEL NEAR THE TIRE, AT HIGH IMPACT. *TR
TL* THE CONTACT OWNS A 2009 BMW 328I. THE CONTACT STATED THAT WHILE APPLYING THE BRAKES, THE VEHICLE ACCELERATED AND CRASHED INTO THE REAR OF ANOTHER VEHICLE. TWO PASSENGERS SUFFERED NECK INJURIES AND THE FRONT AND SIDE AIR BAGS DEPLOYED. THE CONTACT STATED THAT THE VEHICLE CONTINUED TO ACCELERATE WHILE THE BRAKES WERE APPLIED. THE CONTACT CALLED THE MANUFACTURER AND FILED A COMPLAINT. THE VEHICLE WAS NOT REPAIRED. THE FAILURE MILEAGE WAS 30,000.
2009 BMW 328I WITH 17K MILES MALFUNCTIONED CAUGHT FIRE AND EXPLODED. I WAS INJURED BY THE FIRE GETTING OUT. IT WAS A TOTAL LOSS VEHICLE FIRE CAUSING PERSONAL INJURY. IN ADDITION TO THE COST OF THE CAR THERE WAS ADDITIONAL 20K PERSONAL PROPERTY DAMAGE. IT WAS NOT CAUSED BY COLLISION OR OPERATOR ERROR. ON 15 NOV 2010 APPROX 7: 30PM AFTER ABOUT 8 MINS OF DRIVING MY CAR STARTED TO LOSE POWER AND THE SES LIGHT CAME ON. IT ACTED AS IF IT WAS RUNNING OUT OF GAS I PULLED OVER OFF OF THE SHOULDER IN THE GRASS. THE CAR DIED AND WOULD NOT START BACK UP I TOOK MY FLASH LIGHT AND LOOKED UNDER THE HOOD.I DID NOT SEE ANYTHING OR NOTICE ANYTHING UNUSUAL. AFTER A LITTLE TIME THE CAR STARTED BACK UP, THE SES LIGHT DID NOT COME BACK ON. IT WAS DARK OUTSIDE, I WAS OUT OF STATE AND BMW WAS CLOSED SO I TURNED BACK. I DROVE APPROX 1 BLOCK TO A DRIVEWAY WHERE I STOPPED AND CALLED MY HUSBAND TO SAY I WOULD NOT COME HOME UNTIL MY CAR COULD BE SEEN. I BEGAN TO DRIVE BACK TOWARDS LONGVIEW, TX. I ENTERED THE HIGHWAY ON THE OTHER SIDE OF THE ROAD AT ABOUT 50 MPH MY CAR BEGAN LOSING POWER. THE ENGINE MADE A LOAD NOISE AND THE RPM GAUGE WENT UP TO 7000 RPMS I WAS IN TRAFFIC AND NEEDED TO PULL OVER. I PUT THE CAR IN NEUTRAL AND COASTED AT APPROX 40 MPH I PUT THE CAR IN 4TH GEAR AND IT REDLINED AGAIN. I PUT IT BACK INTO NEUTRAL THE CLUTCH WENT TO THE FLOOR. STILL COASTING IN TRAFFIC I GOT OFF THE ROAD AS SOON AS I COULD . IT DIED ON TOP OF A BRIDGE WITH A NARROW SHOULDER. I TURNED OFF THE CAR AND CALLED ROADSIDE ASSISTANCE, WHILE TALKING TO THEM I SEEN FLAMES COMING FROM THE DRIVERS FRONT WHEEL AREA. WITHOUT A SECOND THOUGHT I GOT OUT OF THE CAR I UNDID MY SEAT BELT OPENED THE DRIVERS DOOR AND JUMPED OUT ONLY MY CELL IN HAND. THERE WAS A WALL OF FLAMES TALLER THAN ME I GOT BURNED GETTING AWAY FROM THE CAR I RAN THROUGH THE FLAMES INTO ON COMING TRAFFIC AND WAS ALMOST HIT BY AN 18 WHEELER. I WAS IN THE MIDDLE OF THE BRIDGE WHEN I HEARD THE 1ST EXPLOSION AND THE 2ND AS I RAN OFF OF THE BRIDGE. *TR
My vehicle malfunctioned last week because of the fault harness. Vehicle had a slight fire and now is not drivable. BMW does not want to comply.
WHILE DRIVING IN HEAVY TRAGIC, SMELLED SOMETHING BURNING, WENT TO PULL OUT OF TRAGIC AND FELT MY [XXX] ON FIRE, THE HEAT SEATER BURNED A HOLE IN THE SEAT AND MELTED SEAT COVER TO MY PANTS CAUSING MUCH DISCOMFORT AND RUINED JEANS. REPORTED IT TO BMW AND THEY OFFERED TO DISCONNECT THE ELECTRICITY TO THE SEAT. NOT SATISFIED, NOT IMPRESSED. VERY DANGEROUS. VEHICLE WAS ON HIGHWAY WHEN INCIDENT HAPPENED. WAS LUCKY TO GET OUT OF TRAGIC TO EXIT. WHILE DRIVING PUT MY HAND TO FEEL PROBLEM AND BURNED FINGER TIP. INFORMATION Redacted PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).
TL* THE CONTACT OWNED A 2009 BMW X3. WHILE DRIVING APPROXIMATELY 20 MPH, WHITE SMOKE EMERGED FROM THE ENGINE COMPARTMENT. THE CONTACT PULLED THE VEHICLE OVER TO THE SIDE OF THE ROAD AND NOTICED SPARKS FROM THE ENGINE TO THE GROUND AS A FIRE IGNITED. THE FIRE DEPARTMENT EXTINGUISHED THE FIRE AND FILED A REPORT. THE CONTACT ALSO RECEIVED A RECALL NOTIFICATION FOR NHTSA CAMPAIGN NUMBER: 17V683000 (ENGINE AND ENGINE COOLING). THE VEHICLE WAS NOT TAKEN TO THE DEALER FOR DIAGNOSTIC TESTING. THE INSURANCE COMPANY TOWED THE VEHICLE TO A TOW LOT WHERE IT WAS DEEMED DESTROYED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 123,000.
WE CAME HOME AND PARKED THE BMW IN THE ATTACHED GARAGE. TEN MINUTES LATER I HEARD A NOISE FROM THE GARAGE. I LOOKED INTO THE GARAGE AND FOUND THE ENGINE COMPARTMENT OF THE BMW ON FIRE. I CALLED THE FIRE DEPARTMENT WHO CAME AS QUICKLY AS A VOLUNTEER DEPARTMENT CAN. BY THE TIME THE FIRE WAS OUT BOTH CARS IN THE GARAGE AND THE HOUSE HAD BEEN BADLY BURNED.
THE VEHICLE WAS PARKED AND UNMOVED IN MY DRIVEWAY FOR SEVERAL DAYS. IT SUDDENLY BROKE OUT IN FLAMES (ORIGINATING IN THE ENGINE COMPARTMENT). THE FIRE GREW QUITE LARGE AND THE CAR EXPLODED (THE POLICE OFFICER'S WORD). SECURITY CAMERAS ON THE PROPERTY SHOW NO ONE IN THE AREA TO TAMPER WITH THE CAR. THIS WAS SPONTANEOUS COMBUSTION. A GOOGLE SEARCH OF "2009 BMW X3 FIRE" SHOWS MANY OTHER SIMILAR INCIDENTS.
TL*THE CONTACT OWNED A 2009 BMW X3. THE CONTACT STATED THAT AFTER PARKING HIS VEHICLE AT 9 AM HE RECEIVED A CALL AT 2 PM STATING THAT HIS VEHICLE WAS ON FIRE. WHEN HE WALKED OUTSIDE HE SAW FLAMES COMING FROM THE VEHICLE. THE FIRE DEPARTMENT EXTINGUISHED THE FIRE AND A REPORT WAS FILED. THE POLICE ALSO RESPONDED AND FILED POLICE REPORT #2010-0000-122. THE VEHICLE WAS TOWED TO A BMW DEALER WHO STATED THAT THEY COULD NOT IDENTIFY THE CAUSE OF THE FIRE. THE VEHICLE WAS DESTROYED. THE FAILURE MILEAGE WAS APPROXIMATELY 25,000.
I OWN BMW 320D 2009, MY PROBLEM WITH THE CAR IS EXACTLY THE OPPOSITE, AS MY CAR SUDDENLY ACCELERATE BY ITS SELF, AS I GO DOWN FROM SAY 75 MPH AND RELEASE THE BRAKES, SUDDENLY THE CAR SPEEDS UP AGAIN. THIS IS HAPPEN TO ME SEVERAL TIMES AND BMW SAYS THIS WAS NOTHING I WAS ASSUMING THIS, AFTER COMPLAINED AND COMPLAINED, FINALLY AN IGINUER LOOKED AT MY CAR AND KEPT IT FOR A DAY, BUT ONLY TO SAY NOTHING IS WRONG. IT KEEPS HAPPENING AND HAPPENING AND BMW DOES NOT REACT, AS I MENTIONED TOYOTA IN ONE OF MY LETTERS TO THEM, THEY ANSWERED ME ANGRY WITH WE NOT TOYOTA. TO THIS POINT I KEEP COMPLAINING ND COMPLAINING AND ALSO USE MY OTHER CAR MORE OFTEN. *TR
I had started my car drove out of my parking lot as I approached the highway the first intersection everything went dead no lights, snow warning lights just completely shut down and rumble as if the engine was gonna fall out a police man passed me. I was stuck in the middle of the highway. Help me push my vehicle off the road and sat with me while I called AAA. He could not get the car started. It was not the battery. He also only checked the battery terminals under the hood he hooked his portable battery charger. just gonna let me drive home hooked up, but it would not start.
The battery safety terminal deployed while I was driving down the mountain, causing unsafe conditions for myself and drivers around me. Car turned completely off and unable to turn it back on. Lost power steering and braking capabilities. No accidents or airbags were deployed to cause the battery safety teminal to deploy
Driver side drive shaft fell off while driving on the highway. Very dangerous, merging from one highway in onto another in the middle of gridlock. No lights on prior to failure, just completely snapped off, ripped thru my oil pan and coolant hoses. Was shown the damage when I brought it to a repair shop.
The contact owns a 2009 BMW X3. The contact received notification of NHTSA Campaign Number: 22V119000 (Engine and Engine Cooling) however, the part to do the recall repair was unavailable. The contact stated that the vehicle started to overheat and she was only able to drive the vehicle for a few miles. The contact stated that smoke was coming from under the hood and from the exhaust. The contact stated that she had stopped driving the vehicle for fear of the vehicle catching on fire. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The failure mileage was unknown. Parts distribution disconnect.
Presentate dai proprietari di questo anno modello e non verificate da NHTSA: il racconto di una persona, non un fatto accertato.
BMW of North America, LLC (BMW) is recalling certain 2008-2013 128i and 135i Convertibles, 128i, 135i, and M Coupes, 2007-2010 X3 30si and X3 xDrive30i, 2013-2015 X1 sDrive28i, X1 xDrive28i and X1 xDrive35i, 2007-2013 328i, 328i xDrive, 335i, 335is, 335i xDrive and M3 Coupes, 2006-2011 328i, 328xi, 328i xDrive, 325i, 325xi, 330i, 330xi, 335i, 335xi, 335i xDrive and M3, 2009-2011 335D, 2006-2012 325xi, 328i, 328xi and 328i xDrive, 2010-2011 X6 ActiveHybrid, 2007-2013 328i, 335i, 335is, M3 Coupes, X5 30si, X5 xDrive30i, X5 xDrive35i, X5 48i, X5 xDrive48i, X5 xDrive50i and X5 M, 2009-2013 X5 xDrive35d and 2008-2014 X6 xDrive35i, X6 xDrive50i and X6M vehicles equipped with non-desiccated driver frontal air bag inflators containing phase stabilized ammonium nitrate (PSAN) that were used as interim remedy parts for previous Takata recalls. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Rimedio: BMW will notify owners, and dealers will replace the driver air bag. On X5 and X6 vehicles, only the inflator will be replaced. All repairs will be performed free of charge. The recall began March 11, 2020. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2008-2011 128i and 2007-2011 328i, 328xi, 328i xDrive, 525i, 525xi, 528i, 528xi, 530i, 530xi, X3 3.0si, X3 xDrive30i, X5 xDrive30i, Z4 3.0i, Z4 3.0si and Z4 sDrive30i vehicles. The heater for the positive crankcase ventilation (PCV) valve may short circuit.
Rimedio: BMW will notify owners, and dealers will replace the PCV valve heater, free of charge. Interim letters were mailed on November 27, 2017. Owners will receive a second notification by the end of October 2018. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2006-2010 BMW X3 2.5i, X3 3.0i and X3 xDrive30i Sports Activity Vehicles. The front passenger seat occupant detection mat that determines if, and how, the passenger frontal air bag should deploy in a crash may fatigue and develop cracks which could lead to a system failure.
Rimedio: BMW will notify owners, and dealers will replace the front passenger seat occupant detection mat, free of charge. Interim owner notification letters were mailed on November 27, 2017. A second notification letter will be sent when parts are available. Owners may contact BMW customer service at 1-800-525-7417.
Pubblicati per anno modello, non per VIN: potrebbero non riguardare questo veicolo o essere già stati eseguiti. Verifica con un concessionario.
Water may come into contact with the starter relay and gradually cause corrosion. This could affect the electrical connection inside the relay and make the engine difficult to start. It may also result in a short circuit and could cause the starter to overheat leading to a fire when the vehicle is in motion or when it is parked with the ignition off. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Due to a manufacturing failure, the protection of the two outer headrests in the second row is reduced. In the event of a collision or accident, passengers could be injured. In addition, headrest parts may become exposed and also cause serious injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The RSW22 starter with reinforced water tightness (RWT) may experience increased abrasion of the magnetic contact, causing deposits to build up at the lowest point inside the relay. These deposits may increase relay contact resistance, leading to starting failures or short circuits. If a short circuit occurs, either when attempting to start the vehicle or while driving due to vibration-related movement of the deposits, it could cause a thermal event and increase the risk of fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Damaged brake discs may have been fitted to the front axle. This can lead the brakes to fail when a heavy load is placed on the wheel concerned, increasing the risk of accident and injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Failure to bolt the plus voltage (B+) cable tightly enough to the starter generator may result in contact problems and an increase in contact resistance at the bolted connection. This may in turn lead to local overheating and the vehicle catching fire or to the engine stalling while the vehicle is coasting. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The positive battery cable of the starter-generator may not have been manufactured correctly. This could result in a loose electrical connection, leading to excessive contact resistance. The vehicle cannot charge or start. Contact points in the starter-generator could overheat and cause a vehicle fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the inflator of the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments of the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The driver airbag inflator may malfunction due to long-term degradation. In this case, if the airbag is deployed in an accident, the internal pressure in the inflator may be too high. The inflator could burst. Metal fragments may cause injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The failure concerns the RSW22 starter, type RWT (reinforced for watertightness). Increased abrasion of the magnetic contact can lead to the formation of deposits at the lowest point of the relay interior. This in turn can increase the resistance of the relay contact, causing accidental ignition or even short circuits, possibly leading to a thermal reaction and fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The failure concerns the RSW22 starter, type RWT (reinforced for watertightness). Increased abrasion of the magnetic contact can lead to the formation of deposits at the lowest point of the relay interior. This in turn can increase the resistance of the relay contact, causing accidental ignition or even short circuits, possibly leading to a thermal reaction and fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The failure concerns the RSW22 starter, type RWT (reinforced for watertightness). Increased abrasion of the magnetic contact can lead to the formation of deposits at the lowest point of the relay interior. This in turn can increase the resistance of the relay contact, causing accidental ignition or even short circuits, possibly leading to a thermal reaction and fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The steering system sensor may malfunction causing an unintended steering movement of the vehicle. This increases the risk of accidents and injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The screw connection of the servo unit on the gear rack casing of the steering system may be faulty. This could cause the steering system to fail and become blocked, increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Due to faulty rear-most screws, the screw fixings of the boot's lashing rails can fail in the event of a rear-end collision with heavy intrusion and penetrate the backs of the rear seats. This increases the risk of injury to the occupants of the rear seats. The vehicles concerned have already been modified in connection with the recall code 0051960500. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant within the integrated inflator of driver airbags can deteriorate during time. If the airbag deploys, it could result in fragments from the inflator casing injuring the vehicle’s occupants. The product does not comply with the Regulation on the approval and market surveillance of Motor Vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Due to faulty rear-most screws, the screw fixings of the boot's lashing rails can fail in the event of a rear-end collision with heavy intrusion, and penetrate the backs of the rear seats. This increases the risk of injury to the occupants of the rear seats. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
A seam on the inflator housing of the driver airbag may not have been correctly welded. In case of accident, when the airbag is deployed, the inflator can burst, releasing metal parts which could cause injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The driver's airbag inflator propellant may deteriorate over time. If activated during an accident, excessive internal pressure may cause the inflator to burst, and metal fragments could pass through the cushion material causing injury to occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Due to a manufacturing error, the weld seam of the integrated transmission control unit (ITCU) may not have been correctly executed. As a result, transmission oil could leak into the ITCU, causing it to fail. This may lead to transmission seizure, increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Abbinati per marca e nome del modello: Safety Gate non pubblica il VIN. Controlla le date di produzione e cita il codice del richiamo al concessionario.