2016 Hyundai Santa Fe
Autres modèles Hyundai
Vérifier un véhicule précis
Cette page décrit le modèle. Pour savoir comment une voiture précise est équipée et si son identifiant est valide, décodez son VIN.
Décoder un VINCette page décrit le modèle. Pour savoir comment une voiture précise est équipée et si son identifiant est valide, décodez son VIN.
Décoder un VIN3 rappels et 236 signalements de propriétaires enregistrés pour cette année modèle.
Presque tout ceci décrit l'année modèle, pas la voiture précise. Rien ici ne renseigne sur le kilométrage, les accidents ou la propriété de ce véhicule : aucun identifiant ne les encode.
2016 HYUNDAI SANTE FE INVOLVED IN A NEAR HEAD ON COLLISION. COMBINED TOTAL SPEED OF IMPACT APPROXIMATELY 80 MPH. TWO OCCUPANTS BOTH WEARING SEATBELTS AT TIME OF CRASH. DRIVER SIDE AND PASSENGER SIDE AIRBAGS DEPLOYED DURING CRASH. PASSENGER SHOULDER HARNESS FAILED (LOCKING MECHANISM DID NOT LOCK) RESULTING IN PASSENGER HEAD IMPACT WITH WIND SHIELD CAUSING SIGNIFICANT DEFORMATION OF WIND SHIELD AND HEAD INJURY TO THE PASSENGER. LAP BELT RESTRAINT PREVENTED PASSENGER FROM SIGNIFICANTLY WORSE INJURY. PHOTOS ARE AVAILABLE. *TR
I was rear-ended and the driver's seat did not maintain it's position and fell into the seat behind it.
Had an accident where driver side front of vehicle was hit. The severity of crash resulted in total loss. The driver was hurt and concussed due to her head hitting the side window, driver side. The vehicle was equipped with front side impact and curtain airbags and all failed to deploy. The other vehicle's side curtains were deployed.
THE CAR WAS AT A COMPLETE STOP IN A DRIVEWAY. THE CAR WAS STILL RUNNING BECAUSE I WAS GETTING OUT OF THE CAR TO GET THE MAIL. I PUT THE CAR IN PARK AND WENT TO GET OUT OF THE VEHICLE. AS I GOT OUT THE VEHICLE STARTED GOING IN REVERSE AND PULLED ME UNDERNEATH THE CAR AND THE VEHICLE RAN OVER ME. I'M NOT SURE IF THE TRANSMISSION SLIPPED OUT OF PARK TO REVERSE ON ITS OWN OR IF THE SHIFTER WASN'T ACTUALLY PLACED IN PARK. I THOUGHT THE VEHICLE COULD SENSE IF NO ONE WAS IN THE DRIVERS SEAT AND AUTOMATICALLY PUT THE CAR INTO PARK OR NEUTRAL. THE HEATED SEATS AND AIRBAG WON'T TURN ON UNLESS IT SENSE WEIGHT IN THE SEAT.
RECENTLY WE COULD NOT UNDO THE SEATBELT THAT OUR 6 YEAR OLD GRANDSON WAS STRAPPED IN. THE MORE TRIED TO EXTEND IT TO RELEASE THE TENSION THE TIGHTER IT BECAME. MY GRANDSON WAS BEING CRUSHED AND WAS SCREAMING. THE VEHICLE WAS NOT RUNNING AND WAS PARKED IN THE DRIVEWAY. I HAD TO RUN INTO THE GARAGE AND GET A PAIR OF SCISSORS AND CUT THE SEATBELT TO GET HIM OUT. TO REPLACE THE SEATBELT IS GOING TO COST OVER $400 AND THE DEALER WILL NOT PAY FOR IT AS THEY SAID IT WAS OUR FAULT.
Driving on a slight upgrade, lost power and smoke started to come out of the vents and from under the hood. Had no brakes and by the time we were able to drift to a stop, the engine compartment was on fire. There was no warning lights. Witnesses saw fire under the car while we were coming to a stop. The car and all contents were totally consumed. Following some research on NHTSA vin decoder we found that this car has the same engine (GDI THETA II) that has been involved in many fires and is involved in class action suits. Even though this car has the same engine, it was never recalled. That may indicate that there are other cars out there that may have the same problem but have not been informed.
We recently had the car to the local dealership for engine problems. It took over 3 months, but they finally determined that the camshaft was "bent" and they had to remove the engine to replace it, costing almost $5000. We had it back for about 3 months but didn't drive it much since my wife works remotely from home now. My son was driving it on the interstate and the engine threw a rod, spilling oil onto the exhaust, which caught on fire. He managed to pull over and get out of the car and by then another motorist had called 911. There was a firetruck at the exit he had just passed who showed up in just a few minutes and put the fire out before the fuel system caught on fire, thankfully. While I'm glad my son was uninjured, I'm still very upset by this, especially since they just worked on the engine. After some searching on the internet, I have found that this is a very common occurance for this vehicle (and other Hyundais) yet the company is not doing anything about it. I also read that there is a separate class action lawsuit for this particular engine (in addition to the one for the smaller 4 cylinder engines), but I'm afraid it will be settled too late to help us out.
WHAT FAILED: The engine — the 3.3L Lambda II GDI V6 (engine family GHYXV03.31XE per the federal emissions label) — failed catastrophically: a connecting rod penetrated the engine block. The failed engine IS available for inspection on request. It has been preserved unrepaired since the failure, the rod penetration of the block is externally visible, and the vehicle is currently at Niagara Hyundai in New York. WHAT HAPPENED / SAFETY RISK: On [XXX], I was driving at approximately 65 miles per hour on [XXX] southbound near Bath, New York, with four occupants aboard, when the engine failed suddenly and without warning — no warning lamps, messages, or symptoms preceded it. The vehicle immediately lost all motive power at highway speed. I was forced off the roadway and through brush and debris to bring the vehicle to a stop. The sudden total loss of power at highway speed created an immediate loss-of-control hazard to my occupants and to surrounding traffic. CONFIRMED BY OTHERS: The tow was dispatched through a 911 emergency call. A New York State Trooper was at the scene and observed the debris trail. The towing company's invoice (T&R Towing and Service, Call #[XXX], [XXX]) records "Break Down," winch recovery, vehicle not drivable, and the tow operator's handwritten condition description: "Motor go Boom." The vehicle is now in the possession of a Hyundai dealership (Niagara Hyundai), and Hyundai Motor America has an open case (#[XXX]); however, Hyundai has refused to inspect or diagnose the engine unless I first pay to repair unrelated damage, so the manufacturer has NOT yet inspected the failure — leaving this safety defect undiagnosed by Hyundai. RELEVANT BACKGROUND: In 2024, Hyundai issued warranty extension TXX8 (15 years / 150,000 miles) for connecting rod bearing failure in this exact engine, acknowledging the failure mode. Mileage at failure was under 100,000 miles. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
Someone backed out of a parking lot and I crashed into their rear passenger side. Other party at fault but my air bags for 2016 Hyundai Santa Fe Sport did not deploy.
WE WERE HIT HEAD ON BY A LARGE PICKUP TRUCK. WE SUSTAINED A LOT OF DAMAGE FROM THIS HEAD-ON COLLISION. WE WERE TRAVELING AROUND 10 MILES AN HOUR BUT THE OTHER CAR WAS GOING AT LEAST 20 MILES AN HOUR. THE AIRBAGS NEVER DEPLOYED DESPITE BEING HIT HEAD ON AND SUFFERING A LOT OF DAMAGE UPON IMPACT. WE WERE SLOWING DOWN FOR A STOP SIGN. THE OTHER CAR TURNED INTO OUR LANE AND WAS ACCELERATING TOWARDS US.
1. Component/System Failure & Availability: The failed component is the engine's internal Camshaft Variable Valve Timing (CVVT) phaser backing bolt within the 3.3L V6 engine assembly. An internal factory bolt unthreaded, backed out, and physically pierced directly through the upper valve cover. The vehicle and intact failed engine are currently located at an authorized Hyundai dealership service center in [XXX], and remain fully available for immediate physical inspection by federal investigators upon request. 2. Safety Risk: An internal engine bolt unthreading and puncturing through the valve cover creates an extreme safety hazard. A high-velocity metal bolt piercing the engine casing causes immediate engine seizure, sudden loss of motive power at highway speeds, loss of power steering/braking assistance, and massive pressurized oil discharge directly onto red-hot exhaust manifolds, posing a severe risk of sudden catastrophic vehicle fire and multi-vehicle highway collisions. 3. Dealer/Independent Confirmation: Yes. The failure was formally inspected, reproduced, and confirmed by an authorized Hyundai dealership service department. Dealership technicians logged official diagnostic findings under Prior Authorization Case #XXX. 4. Inspection by Manufacturer/Others: Yes. The defect was inspected and escalated directly to Hyundai Motor America (HMA) Corporate Engineering. Corporate engineering officially verified the defect and issued Techline Case #XXX, confirming that an internal factory CVVT backing bolt unthreaded and pierced the valve cover, recommending a full engine replacement. 5. Warning Lights & Prior Symptoms: There were no prior warning lamps, check engine lights, unusual sounds, or advance warning symptoms prior to the failure. The internal hardware failure occurred suddenly and without warning while operating the vehicle at standard operating parameters. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
I filed a complaint when the first engine seized. It's a miracle we got off the road safely that day. While it was at the dealership, the engine was replaced with a used engine and covered by my extended warranty from Vroom. I believe the cost was approximately $14,000. I was told the engine had around 30,000 miles on it. I've put around 20,000 miles on this engine and the same thing happened again. This time, the engine had been knocking for a few months. When it started knocking, I took it to the dealership because the new extended warranty by Hyundai was in effect and I assumed it would be covered. Immediately, Autonation Hyundai in Savannah, GA said it would not be covered because it was a used engine. I don't understand why when the engine can be traced and the mileage known by the number on the engine. On XXX, my [XXX] granddaughter took her driving test in the vehicle. About 2 hours later, the engine seized with her driving. We were on the same road and it was about the same time of day. Once again, it was a miracle we got off the road safely. I just talked to Hyundai and we'll see what they say. From the stories I've seen, they'll do anything they can to avoid covering these engines and they get away with it. The people who get hurt the most from this are the ones who can least afford it. I'm a [XXX] widow raising my 5 grandchildren by myself and believed I was getting a good vehicle, mainly due to the report by Consumer Reports magazine. Even after the first engine failed and was replaced, I still wasn't in a financial position to get another vehicle and assumed if something happened again, it would be covered under the extended warranty Hyundai was made to provide. Obviously, that means nothing. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
Purchased a used Santa Fe in January 2026 with 129k mile and at 131k my vehicle's CEL came on and did not function properly while operating. While driving the vehicle failed to accelerate above 25 mph when I pushed the gas. I pulled over to get out of the way of traffic and avoid any accidents. I shut the car off and sat for several minutes before restarting my vehicle. It successfully restarted and I drove home and parked it. I ran CEL diagnostic and received the code P0021. I had the vehicle towed to the local Hyundai dealer and they also pulled the same code and indicated I have an oil consumption issue explained as follows "Timing over advanced. Timing components driven by oil pressure. Inspected cylinders and borescope and found cylinder wall scoring and faulty piston rings. Radiator has crack causing coolant leak. Engine will have to be replaced to remedy oil consumption. Radiator will need to be replaced to remedy leak." resulting in over $12k of repair work. The vehicle's temperature gauge did not indicate any abnormalities nor did the oil light come on to indicate any oil consumption issues. The vehicle was driven from the dealer to my home within city limits/speed and has not replicated the acceleration issue but the CEL remains on as the repair is too costly and is more than what was paid for the vehicle.
Rod bearing failure while driving, engine made a clanking noise. Engine made a loud bang and shut off. It was difficult for the driver to get control of the vehicle and get it to the side of the road. Engine threw the rod and piston through the oil pan causing catastrophic internal damage. The oil had been changed the day prior. The company that changed the oil sent an inspector to evaluate car at the scene. He stated this is a known problem with this engine. He pulled up pictures of other cars that had the same problem, also took pictures of the car oil pan and compared the pictures, they were exactly the same. Car was towed to Hyundai dealership that is refusing to replace the engine.
Beginning about a month ago, I noticed a rattle upon the engine start up that lasted for a 1-2 seconds then stopped and everything sounded normal. I thought it could be b/c of the cold weather. I went in to get a routine oil change on 03/11/2026 and they said the oil looked fine, but it was about a quart low, indicating it was burning some oil somehere. They said to check in in a few months and they would top it up if needed. I asked them about the rattle and they thought is might be from a bad (timing chain tensioner) but said I should get it checked out. I called on Friday 03/13/26 to schedule an appt at my local Hyundai Dealership on 03/17 . The night before(03/16), I was driving my vehicle and suddenly on the road, I heard a loud noise in the engine, and the power shut off, the Engine and oil light came on and I just had enough time to pull off the busy state route. My car would not start or turn over. I had it towed to the dealership and they did determine that it was a "Rod Bearing Failure" that caused the engine to sieze. I provided them evidence of my oil changes which from 10k-93k miles on my car since I have owned it. I have had the oil changed 10 times. They are saying they only allow 8k between oil changes to honor the warranty and have initially denied my claim. The service associate at the dealership said my valvetrain was 'somewhat' dirty, but nothing to where it was the cause for this issue. And since it was the Rod bearing that failed, the exact part that was recalled, he was surprised they were not even offering any good-will offer, to split the cost of the engine replacement. I have reached out to Hyundai Consumer Affairs and am waiting to hear back to see if they will be fair and work with me on this to honor the warranty issue or at least share the cost burden for this "well-known" failure in their engine.
Déposées par des propriétaires de cette année modèle et non vérifiées par la NHTSA : le témoignage d'une personne, pas un fait établi.
1 rappel comporte un avertissement de ne pas conduire ou de stationner dehors. Vérifiez si ce véhicule a déjà été traité avant de le conduire ou de le garer.
Hyundai Motor America (Hyundai) is recalling certain 2016-2018 Santa Fe, 2017-2018 Santa Fe Sport, 2019 Santa Fe XL, and 2014-2015 Tucson vehicles. The Anti-Lock Brake System (ABS) module could malfunction and cause an electrical short, which could result in an engine compartment fire.
Solution : Owners are advised to park outside and away from structures until the recall repair is complete. Dealers will replace the ABS multi-fuse, as necessary, free of charge. Owner notification letters were mailed May 31, 2022. Owners may contact Hyundai customer service at 1-855-371-9460. Hyundai's number for this recall is 218.
Hyundai Motor America (Hyundai) is recalling certain 2013-2017 Santa Fe and Santa Fe Sport vehicles. In the affected vehicles, the secondary hood latch actuating cable may corrode and bind, causing the secondary hood latch to remain in the unlatched position when the hood is closed.
Solution : Hyundai will notify owners, and dealers will replace the secondary latch cable, free of charge. The recall began on August 4, 2017. Owner's may contact Hyundai customer service at 1-855-671-3059. Hyundai's number for the recall is 163.
Hyundai Motor America (Hyundai) is recalling certain model year 2016-2017 Santa Fe vehicles manufactured September 1, 2015 to February 12, 2016. In the affected vehicles, the wires in the front seat belt buckle harnesses may be damaged by the seat's height adjuster mechanism, resulting in a failure to provide an audible warning when front seat occupants do not fasten their seat belts. As such, these vehicles fail to comply with the requirements of the Federal Motor Vehicle Safety Standard (FMVSS) number 208, "Occupant Crash Protection."
Solution : Hyundai will notify owners, and dealers will inspect and reroute the wires in the front seat belt buckle harnesses to their proper locations, as necessary, free of charge. The recall began on April 27, 2016. Owners may contact Hyundai customer service at 1-800-633-5151. Hyundai's number for this recall is 141.
Publiés par année modèle et non par VIN : ils peuvent ne pas concerner ce véhicule, ou avoir déjà été effectués. À confirmer auprès d'un concessionnaire.
A short circuit can occur in the ESP (Electronic Stability Program) unit. This increase the risk of the vehicle catching fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Vehicles may develop an electrical short in the Anti-Lock Brake System (ABS) module, increasing the risk of an engine compartment fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The wiring harness mounted under the bench seat can be damaged by being pinched by the seat hinge when it is folded down. This can lead the curtain airbag not to work, increasing the risk of injuries in the event of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Rapprochés par marque et nom de modèle — Safety Gate ne publie pas de VIN. Vérifiez les dates de production et indiquez le code de rappel au concessionnaire.