5 rappels et 73 signalements de propriétaires enregistrés pour cette année modèle.
Cette page décrit le modèle. Pour savoir comment une voiture précise est équipée et si son identifiant est valide, décodez son VIN.
Décoder un VINPresque tout ceci décrit l'année modèle, pas la voiture précise. Rien ici ne renseigne sur le kilométrage, les accidents ou la propriété de ce véhicule : aucun identifiant ne les encode.
During a recent auto collision my airbags did not deploy. I swerved to avoid another vehicle entering the intersection from my left, he hit my rear left driver's side quarter panel and I subsequently hit a tree. This was noted by the paramedics first on scene as well as by the firemen and police when they arrived. I have notified BMW of North America, USAA insurance (my insurance company), and now you. The vehicle is a total loss and was towed to Leesburg Virginia by roadrunner wrecker service.com
I PARKED MY X5 ON AN INCLINE, PUT THE CAR IN PARK, SET THE PARKING BREAK AND TURNED THE VEHICLE OFF. LOCKED IT AND WENT INSIDE. THERE WERE WORKERS OUTSIDE FOR ABOUT 10 MINUTES BEFORE COMING IN TO THE HOUSE THAT WITNESSED IT SITTING THERE FOR THAT AMOUNT OF TIME. AFTER BEING INSIDE FOR ABOUT 5 MORE MINUTES OR BETTER, I WENT TO LEAVE AND FOUND THAT MY CAR HAD ROLLED AND HIT A TREE. THE PARKING BREAK WORKED SEEING THAT THERE WAS SNOW BUILT UP ON THE BACK TIRES, HOWEVER, YOU CAN SEE FROM THE PICTURES THAT BOTH FRONT TIRES ROLLED. BMW LOOKED INTO IT AND SAID THE CAR DIAGNOSTICALLY CHECKED OUT FINE AND THAT IT IS NORMAL FOR BOTH FRONT TIRES TO ROLL WHILE IN PARK???
I STOPPED AT THE ENTRANCE OF AN APARTMENT COMPLEX AND WAS WAITING FOR THE SECURITY GATE TO OPEN. ONCE I CAME TO A COMPLETE STOP THE AUTO START STOP FUNCTION TURNED THE ENGINE OFF. WHILE STOPPED, WITH MY FOOT STILL ON THE BRAKE, SUDDENLY AND UNEXPECTEDLY, THE ENGINE STARTED AND THE VEHICLE TOOK OFF STRIKING THE SECURITY GATE AS IT WAS OPENING. THE BRAKES DID NOT WORK. NO AIRBAG DEPLOYED EITHER.
I am reporting a suspected high-pressure fuel pump safety defect involving my 2016 BMW X5 xDrive35d, VIN [XXX], with approximately 103,186 miles. The check engine light illuminated and BMW Fort Walton diagnosed failed fuel injectors and recommended injector replacement. I subsequently had the vehicle inspected by Techmaster in Fort Walton, Florida, where metallic shavings and debris were discovered within the high-pressure fuel system. After notifying BMW Fort Walton of these findings, I was advised that my VIN is not included in NHTSA Recall 21V-586: High Pressure Fuel Pump. I am concerned because the metallic contamination found in my vehicle appears similar or identical to the high-pressure fuel pump failure conditions addressed by Recall 21V-586. The contamination may also have caused consequential damage to the fuel injectors and other associated fuel-system components. I respectfully request that NHTSA review whether my vehicle, and potentially other BMW X5 xDrive35d vehicles currently excluded from Recall 21V-586, may be experiencing the same or substantially similar high-pressure fuel pump defect. Replacing only the failed injectors without identifying and correcting the source of metallic contamination could leave debris in the fuel system and potentially result in additional fuel-system failure. BMW Fort Walton has advised me that my VIN is outside the current recall population. I am requesting that this case be reviewed as a potential safety defect and possible issue with the scope of the existing recall. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
The High-Pressure Fuel Pump (HPFP) on my vehicle has experienced a catastrophic premature failure for the second time, presenting a severe and immediate safety hazard. This vehicle was previously serviced under NHTSA Recall 21V-586 in 2022 at 66,165 miles, during which the original defective fuel pump was replaced by an authorized BMW dealership. At approximately 123,000 miles, the replacement pump failed while the vehicle was in operation. When these high-pressure fuel pumps fail, they cause sudden engine stalling, a complete loss of propulsion while driving, and a loss of power-assist for steering and braking. This creates an immediate risk of a high-speed collision on public roadways, especially during highway transit. Furthermore, failure of this component can lead to internal mechanical destruction, creating a potential fuel leak or fire hazard. Because a replacement part mandated by a federal safety recall has failed in the exact same manner after limited mileage, the remedy provided under Recall 21V-586 is demonstrably inadequate to permanently resolve this safety hazard. BMW is currently refusing to cover the repair because the vehicle is just past the 120,000-mile extended warranty limit, leaving a known, recurring safety defect unaddressed. I am filing this complaint to urge NHTSA to investigate the failure rates of BMW's replacement recall pumps, as the current remedy does not guarantee long-term vehicle safety.
2016 BMW X5 xDrive40e. Experiencing intermittent/sudden drivetrain malfunction warnings. Vehicle loses power or enters limp mode while driving. Max eDrive / electric drive becomes disabled even with battery charged. Multiple warning lights appear. Issue appears related to the hybrid system (possible EME, SME, Safety Box, or high-voltage battery faults). This creates a safety risk because power can be lost unexpectedly while moving. Mileage at time of most recent occurrence: 126,500. Problem first noticed 118,000.
The contact owns a 2016 BMW X5 PHEV. The vehicle was serviced under NHTSA Campaign Number: 24V608000 (ENGINE AND ENGINE COOLING, ELECTRICAL SYSTEM), but the failure persisted. The contact stated that a month after the repairs were completed, the coolant connector would stay on and drain the battery. The contact stated that after the vehicle was turned off at night, the coolant connector overheated and the battery drained. The contact needs to jump-start the battery every day. The vehicle was taken to the dealer, and the dealer refused to repair the vehicle, stating that it was already repaired. The contact stated that the coolant connector damaged the EME (Electrical Machine Electronics). The dealer confirmed that the problem may be EME. The vehicle remained at the dealer unrepaired. The contact stated that the failure is worsening. The manufacturer was not made aware of the failure. The failure mileage was 114,865.
I am having a high voltage system box fault. I am within warranty but the dealership is denying me. My in service date is 6-2016.
The component that failed appears to be the hybrid propulsion and charging system, including the high-voltage battery management system and/or integrated charging electronics. The vehicle will not accept a charge from any home or public charging source. The high-voltage battery was replaced approximately one year ago; however, the charging failure persists. The vehicle is available for inspection upon request. In addition to the charging failure, the vehicle displayed drivetrain malfunction and start/stop malfunction warnings. While driving on the highway at normal speed, the vehicle lost power and stopped, creating a hazardous situation in active traffic. This sudden loss of propulsion placed my safety and the safety of other drivers at risk, as surrounding vehicles were traveling at highway speeds. Prior to the failure, warning messages appeared intermittently, including charging system faults and start/stop malfunction alerts. These warnings began approximately one year ago around the time the charging issue started. The vehicle was previously serviced and the high-voltage battery was replaced; however, the underlying issue was not corrected. The root cause is UNKNOWN, but the symptoms suggest a failure within the hybrid control system, charging module, DC-DC converter, or related electrical components. The failure has been persistent and unresolved. I am concerned that defects within the hybrid propulsion system may lead to additional sudden loss of power events.
Subject: Consequential Damage and Failure of Remedy regarding Recall 24V-608 Incident Description: "I am reporting a failure of the manufacturer to provide an effective remedy for Safety Recall 24V-608 (Electric Water Pump) and subsequent consequential damage to the High-Voltage battery system. In September 2023, at approximately 78,000 miles, this vehicle exhibited 'Drivetrain Malfunctions' including Fault Code 0x222626 (EME: internal fault - active short circuit requested) and 0x22271C (Overvoltage in intermediate circuit). The BMW dealer (Fields BMW) failed to diagnose the root cause and instructed me to 'keep driving'. Since the release of Recall 24V-608, it is clear these 2023 faults were early indicators of the coolant pump short-circuiting. This persistent electrical instability has now resulted in a permanent failure of Cell Supervision Circuit #3, causing the high-voltage contactors to open and leaving the vehicle disabled. The dealer is currently attempting to charge for diagnostics and battery removal. I am asserting that the lack of a timely remedy for the coolant pump (which was only recently shielded per the recall) caused a power surge that 'fried' the internal battery circuitry. This is a safety issue as the vehicle experienced a sudden loss of propulsion while in motion. I request that NHTSA investigate BMW’s refusal to cover battery failures caused by the electrical interference of the recalled coolant pump."
Because of this water intrusion, the following safety systems have malfunctioned or failed: • ABS and DSC (stability control) warnings • Chassis stabilization warning • Frontal collision and pedestrian warning malfunction • Airbag system warning • Loss of audible warning tones • MOST bus communication failure • Electrical modules intermittently shutting down or throwing codes These failures affect braking, stability control, crash avoidance, and driver alerts, creating a significant safety risk while driving. This is not normal wear or maintenance. Many BMW owners have reported the same issue: clogged or poorly designed sunroof drains that route water directly into areas containing critical electronics. Once water reaches these modules, it causes electrical shorts and safety system failures that require expensive repairs. BMW dealerships typically diagnose this as “water damage,” but the location of the drains and the placement of the electronics indicate a design flaw that allows a simple drain issue to disable major safety systems. I am filing this complaint because the water intrusion should not be able to cause total failure of ABS, DSC, collision warning, and airbag-related systems. This is a safety-related design defect, not wear and tear. I request NHTSA review and investigate BMW sunroof drain failures and their impact on essential vehicle safety functions.
I am reporting a safety issue related to the BMW recall 18V-755 affecting the EGR cooler on my 2016 BMW X5 diesel. My vehicle experienced symptoms consistent with a failing EGR cooler, including coolant loss and engine warning lights. Despite this recall being active for my model and VIN, BMW has denied coverage, stating either that the cooler was already replaced twice or that my vehicle is not eligible—without providing sufficient documentation or explanation. I am concerned that the recall remedy was not properly applied or that faulty replacement parts were used. I am requesting that NHTSA investigate whether BMW is properly honoring recall 18V-755 and ensuring safe, effective remedies are provided to affected customers like myself. I also request investigation into the lack of transparency and failure to document completed recall work. My VIN is [XXX] , and I can provide dealer records, service history, and diagnostic reports upon request. * What component or system failed or malfunctioned, and is it available for inspection upon request? EGR Cooler, it is available for inspection. * How was your safety or the safety of others put at risk? The vehicle is now showing dangerous symptoms consistent with a thermal event risk, which this recall specifically warned about. The EGR cooler is leaking coolant into the intake system, which can mix with soot and lead to engine fires, according to BMW’s own technical documentation. * Has the problem been reproduced or confirmed by a dealer or independent service center? Yes and the cooler has been replaced twice. * Has the vehicle or component been inspected by the manufacturer, police, insurance representatives or others? It has been inspected at Fremont BMW once, Valley BMW twice. * Were there any warning lamps, messages or other symptoms of the problem prior to the failure, and when did they first appear? Yes, low coolant warning, loss of coolant with no leaks. Problem first occurred April 2024 INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
1) Crankshaft Sensor MIL Light 2) Drive train malfunction, 3) Start and Stop malfunction, 3) MIL for Catalytic convertor 4) MIL light for Catalytic Convertor & O2 sensor failure. The Vehicle has (97,000 K), and the BMW dealer would not cover the costs. However there's TSB published for this vehicle, yet its not being honored by the dealer who claims that the Emissions warranty expired after 8 years or 80,000 miles.
High pressure fuel pump replaced after the original recall and fail again 45k miles later during driving.
The contact owns a 2016 BMW X5. The contact stated that the vehicle was repaired under NHTSA Campaign Number: 21V586000 (Fuel System, Diesel); however, the repair failed to prevent the failure from occurring. The contact stated that on three separate occasions, the same recall failure had occurred. The vehicle was towed to the same local dealer where it was diagnosed with a fuel pump failure due to debris inside the fuel pump. The vehicle was not repaired due to the cost. The manufacturer was made aware of the failure. The failure mileage was approximately 40,239.
Déposées par des propriétaires de cette année modèle et non vérifiées par la NHTSA : le témoignage d'une personne, pas un fait établi.
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Solution : Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2013-2018 328d, 328d xDrive, 2014-2018 328d Sports Wagon, 328d xDrive Sports Wagon, 2014-2016 535d, 535d xDrive, 2015 740Ld xDrive, 2015-2017 X3 xDrive28d SAV, and 2014-2017 X5 xDrive35d SAV diesel vehicles equipped with an Exhaust Gas Recirculation (EGR) module with an integrated cooler. The EGR cooler may leak internally, causing coolant to mix with diesel engine soot, which could result in smoldering particles and a melting intake manifold.
Solution : Dealers will replace the EGR cooler and inspect the intake manifold, replacing it as necessary, free of charge. This recall includes all vehicles previously recalled under 18V-755. Vehicles previously recalled under 18V-755 will need to have the new remedy performed for this recall. An interim owner notification letter was mailed on January 18, 2022. The remedy is expected to be available in June 2022. Owner notification letters were mailed on July 6, 2022. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2014-2018 328d, 328d xDrive, X5 xDrive35d, 2014-2016 535d, 535d xDrive, 2015 740Ld xDrive, and 2015-2017 X3 xDrive28d vehicles. The high-pressure fuel pump may fail.
Solution : Dealers will replace the high-pressure fuel pump, free of charge. Owner notification letters were mailed on January 14, 2022. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2013-2018 BMW 328d and 328d xDrive, 2014-2018 328d Sports Wagon and 328d xDrive Sports Wagon, 2014-2016 535d and 535d xDrive, 2015 740Ld xDrive, 2015-2017 X3 xDrive28d SAV and 2014-2017 X5 xDrive35d SAV vehicles equipped with an Exhaust Gas Recirculation (EGR) module with an integrated cooler. If the EGR cooler leaks internally, the coolant can mix with diesel engine soot. The high EGR temperatures may result in these particles possibly smoldering and melting the intake manifold.
Solution : BMW will notify owners, and dealers will inspect and replace the EGR cooler as necessary. If a leak has already occurred, the engine intake manifold will also be replaced. These repairs will be made free of charge. The recall began May 13, 2019. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain model year 2016 X5 xDrive40e vehicles manufactured July 29, 2015, to September 9, 2015. The affected vehicles have a Digital Motor Electronic (DME) control unit that may have a loose electrical ground cable, possibly causing an under-voltage condition which would result in the transmission shifting to neutral.
Solution : BMW will notify owners, and dealers will tighten the ground cable, free of charge. The recall began February 6, 2017. Owners may contact BMW customer service at 1-800-525-7417.
Publiés par année modèle et non par VIN : ils peuvent ne pas concerner ce véhicule, ou avoir déjà été effectués. À confirmer auprès d'un concessionnaire.
Water may come into contact with the starter relay and gradually cause corrosion. This could affect the electrical connection inside the relay and make the engine difficult to start. It may also result in a short circuit and could cause the starter to overheat leading to a fire when the vehicle is in motion or when it is parked with the ignition off. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The engine starter’s electrical contacts may overheat and cause the vehicle to start improperly. Continued starting attempts can intensify the overheating and ignite surrounding components, potentially leading to a vehicle fire while driving or shortly after parking. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The RSW22 starter with reinforced water tightness (RWT) may experience increased abrasion of the magnetic contact, causing deposits to build up at the lowest point inside the relay. These deposits may increase relay contact resistance, leading to starting failures or short circuits. If a short circuit occurs, either when attempting to start the vehicle or while driving due to vibration-related movement of the deposits, it could cause a thermal event and increase the risk of fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The positive battery cable of the starter-generator may not have been manufactured correctly. This could result in a loose electrical connection, leading to excessive contact resistance. The vehicle cannot charge or start. Contact points in the starter-generator could overheat and cause a vehicle fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The chemical substances in the inflators of the TAKATA PSDI4 airbags may deteriorate over time, particularly in warm, humid climates. This could cause the airbag to rupture with too much force in the event of an accident, which could lead to serious or even fatal injuries in the worst-case scenario. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The failure concerns the RSW22 starter, type RWT (reinforced for watertightness). Increased abrasion of the magnetic contact can lead to the formation of deposits at the lowest point of the relay interior. This in turn can increase the resistance of the relay contact, causing accidental ignition or even short circuits, possibly leading to a thermal reaction and fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The failure concerns the RSW22 starter, type RWT (reinforced for watertightness). Increased abrasion of the magnetic contact can lead to the formation of deposits at the lowest point of the relay interior. This in turn can increase the resistance of the relay contact, causing accidental ignition or even short circuits, possibly leading to a thermal reaction and fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The hollow shaft of the servomotor was not welded correctly. The weld may not be able to withstand high braking pressure build-up and may break. In this case, the reduced braking performance requires greater force and the braking distance may increase. In addition, the ABS and DSC brake control systems are not assisted. This increases the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The software-based overload protection function cannot sufficiently prevent the starter being overloaded in the event of repeated long start-up attempts. The starter may overheat or sparks may be produced as a result of an increased current flow. This increases the risk of a fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The gas generator in knee airbag modules was not properly inserted into the air cushion, resulting in the cushion failing to unfold sufficiently. As a result, it may not be able to deploy correctly in the event of an accident, leading to a reduction in the restraint effect, increasing the risk of injury to the occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
A seam on the inflator housing of the driver airbag may not have been correctly welded. In case of accident, when the airbag is deployed, the inflator can burst, releasing metal parts which could cause injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The stated maximum load specified in the user manual is incorrect. This could cause users to overload the vehicle, potentially leading to damage to the car and an increased risk of accidents and injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The integrated braking system could be compromised, which could lead to an unexpected failure of the hydraulic braking assistance, thereby requiring greater pressure on the brake pedal. This can result in a longer braking distance, as well as failure of the Anti-lock Braking System (ABS) and the Dynamic Stability Control (DSC), increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The dashboard in the affected vehicles may not have been manufactured to the manufacturer specifications. In the event of anaccident, the passenger side airbag may not deploy as intended which could increase the risk of injury to the frontpassenger. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Due to a manufacturing error, the weld seam of the integrated transmission control unit (ITCU) may not have been correctly executed. As a result, transmission oil could leak into the ITCU, causing it to fail. This may lead to transmission seizure, increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Rapprochés par marque et nom de modèle — Safety Gate ne publie pas de VIN. Vérifiez les dates de production et indiquez le code de rappel au concessionnaire.