10 llamadas a revisión y 9 quejas de propietarios registrados para este año del modelo.
Esta página describe el modelo. Para ver cómo está equipado un coche concreto y si su identificador es válido, decodifica su VIN.
Decodificar un VINCasi todo esto describe el año del modelo, no el coche concreto. Nada de aquí dice nada sobre el kilometraje, los accidentes o la titularidad de este vehículo: ningún identificador los codifica.
This issue of the Starter not functioning properly was identified by the manufacturer and brought to my attention through their correspondence. Later confirmed on the NHSTA website. To date, no fix has been made available.
The contact owns a 2020 BMW X6. The contact stated that while the vehicle was parked and attempting to start the vehicle, the vehicle failed to start. The vehicle was towed to an independent mechanic, where it was diagnosed with battery failure. The contact was informed that the battery needed to be replaced. The vehicle was repaired; however, the failure reoccurred. The contact stated that while driving at an undisclosed speed, the engine seized. The contact stated that while attempting to start the vehicle, the vehicle failed to start. In addition, the engine overheating warning light was illuminated. The contact stated that the failure had occurred while the contact was driving on a busy interstate. The contact stated that the failure could have caused a crash. In addition, the contact stated that the situation was very dangerous and scary. The vehicle was towed to the dealer, and the contact was informed that the failure was the result of over attempting to start the vehicle, which might have damaged the battery. In addition, the contact was informed that the battery might need to be replaced. The contact stated that neither the dealer nor the independent mechanic had mentioned the unrepaired recall. The contact later received a recall notification for NHTSA Campaign Number: 25V644000 (Electrical System); however, parts were not yet available. The manufacturer was made aware of the failure but provided no assistance. The failure mileage was approximately 67,786.
Vehicle: 2020 BMW X6M Problem Category: Interior / Visibility / Structural Integrity Description of the Safety Issue: The dashboard material in my 2020 BMW X6M is peeling, lifting, and separating from the underlying structure. This is occurring without misuse, damage, or excessive wear. The defect creates reflective glare on the windshield and presents a visual distraction while driving, particularly in sunlight. The separation appears to be a material or adhesive failure and is not isolated. Multiple BMW X5/X6 owners have reported the same issue, indicating a pattern of premature dashboard deterioration. This defect affects driver visibility and concentration and could increase the risk of an accident. Repair costs are estimated at approximately $4,000 due to full dashboard replacement. BMW has declined assistance, citing warranty expiration, despite the nature of the defect indicating a manufacturing or materials failure rather than normal wear and tear.
The vehicle would not start and left me stranded over 40 miles from home. I was unable to start the vehicle for over an hour. The road side service was unable to start the vehicle.
The contact owns a 2020 BMW X6. The contact stated that the vehicle failed to start, with the message "Check Control - Repeat Start Attempt" displayed. In addition, the check engine warning light remained illuminated. The cause of the failure was not yet determined. The manufacturer was notified of the failure, but no assistance was offered. The contact was informed that the VIN was not included in NHTSA Campaign Number: 24V576000 (ELECTRICAL SYSTEM, ENGINE AND ENGINE COOLING). The contact stated that the vehicle had experienced the failure listed in the recall. The failure mileage was 59,900.
I’ve been having issues with the front end since I purchased the vehicle. The dealership had not diagnosed this issue yet in 3 years. It had caused my vehicle to be in the shop continuously, my front driver side tire is worn out. I had to replace all brakes and rotors after 2 years, numerous sensor issues, radiator loses fluid as well as software issues.
Duluth BMW Dealership service department repaired a recall thats directly related to an issue due to a water pump leak. My X6 currently has a water pump leak for which they are charging me $1600.00 to repair. However, it is the water pump leak is what causes the potential for the engine to overheat and start the vehicle to catch fire. I purchased my 2020 in 2019 which was the first batch to be made by BMW. Apparently they're stating the X3, X4 and X5. My X6 have this very same issue and BMW have the responsibility to fix this water pump issue. It's not only the X3,4 and 5. Please help me. It's unfair that BMW pass their known problems on to the consumers who already pay an outstanding large amounts of monies for their vehicles. I kept up with my maintenance service ad scheduled and I am perplexed that they did not see that issue when I brought it in in March 2024. It is now October 2024. PLEASE HELP!
On July 27, 2024, the parking brake on this car would not disengage, thus, I was unable to drive my car. We had to turn off the car for 15 minutes and then step on the gas and brake at the same time at which point the park brake "disengaged." I believe this is a safety/manufacturer issue that needs to be addressed and should be under a broader warranty protection (like 100,000 miles or more).
On December 28, 2023, the "Fasten Seat Belt" sign (rear passenger side seat) and sensor in my BMW x6 starting buzzing even though no one is seating on that seat. I subsequently brought my car to the dealership and the service consultant did an ocular inspection of my seat belt and looked inside the buckle with a flashlight because the seat belt will not lock in place. I was subsequently told that the metal that is supposed to hold the seat belt in the buckle is missing or stuck. Because at that time my car has 59,000 miles, I was told that the warranty has now expired (50,000) and that I have to pay for the diagnoses and fixing of the car seat. Now, the "Fasten Seat belt: sensor for the rear middle seat is also lighted and making the "buzzing sound" even though no one is seating in the middle seat. I believe that my seat belts have become defective and given that I purchased my car around May 10, 2020 - I should not have to pay for fixing seat belt problems for a new car given the safety need for these belts. I would like NTSB to compel BMW to fix my seatbelts.
Presentadas por propietarios de este año del modelo y sin verificar por la NHTSA: el relato de una persona, no un hecho probado.
BMW of North America, LLC (BMW) is recalling certain 2020 340I, X6, 2020-2025 840I, 2020-2022 740LI, 2019-2020 X7, and X5 vehicles. After repeated attempts, the starter motor may overheat from an electrical overload.
Solución: Dealers will replace the engine starter, free of charge. This recall includes vehicles repaired under recall 24V576 and those owners will need to have their vehicle repaired again. Owner notification letters were mailed February 9, 2026. Owners may contact BMW customer service at 1-800-525-7417. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov November 17, 2025.
BMW of North America, LLC is recalling certain 2019-2020 X5, X7, 2020 3 Series Sedan, X6, 2020-2021 7 Series Sedan, 2020 8 Series Convertible, 8 Series Coupe, and 2020 8 Series Gran Coupe vehicles. Please see the recall report for the complete list of models. In the event the starter motor fails, repeated attempts to start the vehicle can cause the starter motor to overheat from an electrical overload.
Solución: Dealers will update the vehicle software, free of charge. Owner notification letters were mailed September 27, 2024. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2022 4 Series Gran Coupe (430i, 430i xDrive, M440i xDrive); 2019-2022 X5 sDrive40i, X5 xDrive40i, X5 xDrive50i, X5 M50i, X5M; 2021-2022 X5 xdrive45e; 2020-2022 X6 sDrive40i, X6 xDrive40i, X6 xDrive50i, X6M and 2019-2023 X7 xDrive40i, X7 xDrive50i, X7 M50i, X7 xDrive60i, X7 M60i, X7M, Alpina XB7 vehicles. The roof function control unit may be programmed incorrectly, allowing the sunroof to close without the key fob present inside the vehicle. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 118, "Power-Operated Window Systems."
Solución: Dealers will reprogram the roof function control unit, free of charge. Owner notification letters were mailed June 20, 2022. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2019-2021 X3 sDrive30i, X3 xDrive30i, X3 M40i, X3M, X4 xDrive30i, X4 M40i, M550i, X4M, X5 sDrive40i, X5 xDrive40i, X5 xDrive50i, X5M, X5 M50i, X7 xDrive40i, X7 xDrive50i, X7 M50i, Alpina XB7, 330i, 330i xDrive, M340i, M340i xDrive, and 8 Series Coupe, Convertible and Grand Coupe, 840i, 840i xDrive, M850i xDrive, M8, 2020-2021 530e, 530e xDrive, 330e, 330e xDrive, 745Le, 745Le xDrive, X5 xDrive45e, X3 xDrive30e, X6 sDrive40i, X6 xDrive40i, X6 xDrive50i, X6 M50i, X6M, 530i, 530i xDrive, 540i, 540i xDrive, M550i xDrive, M5, 740i, 740Li, 740Li xDrive, M760i Drive, M760Li xDrive, 750Li xDrive Alpina, Alpina B7 xDrive, and 2021 4 Series Coupe 430i, 430i xDrive, M440i xDrive vehicles. When shifting into Reverse, a small portion of the rearview image may be obscured, or the screen may not illuminate. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 111, "Rear Visibility."
Solución: BMW will notify owners, and dealers will inspect the rearview camera software and update it if necessary, free of charge. The recall began April 16, 2021. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2020-2021 8 Series Coupe, Grand Coupe and convertible 840i, 840i xDrive, M850i xDrive, M8 and 740 Li, 740 Li xDrive, 750 Li xDrive, M760 Li xDrive, X6 sDrive40i, X6 xDrive40i, X6 xdrive50i, X6 M50i, X6M, and 2019-2021 X5 sDrive40i, X5 xDrive40i, X5 xDrive50i, X5 M50i, X5M, X7 xDrive40i, X7 xDrive50i, X7 M50i, and 2021 M3, M3 Competition, M4 Coupe, M4 Competition Coupe, X5 xDrive45e, 745 Le xDrive. The rotor and shaft within the integrated brake system may not have been welded properly and could separate during a hard braking event, possibly resulting in a loss of the Antilock Brake System (ABS) and braking assistance.
Solución: BMW will notify owners, and dealers will replace the integrated brake system, free of charge. Owner notification letters were mailed on May 25, 2021. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2020 X5 sDrive40i, xDrive40i, X5 M50i, X5M, X7 xDrive40i, X7 M50i, X6 xDrive40i, X6 M50i and X6M vehicles and 2021 X5 xDrive45e vehicles. The weld between the front axle support and the right front control arm bearing bracket may separate.
Solución: BMW will notify owners, and dealers will replace the front axle support, free of charge. The recall began December 18, 2020. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2020-2021 X5 sDrive40i, xDrive40i, xDrive50i, X5 M50i, X5M, X6 sDrive40i, xDrive40i, X6 M50i, X6M, X7 M50i and 2021 X5 xDrive45e vehicles. The headlamps may allow a blue light to illuminate. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 108, "Lamps, Reflective Devices, and Associated Equipment."
Solución: BMW will notify owners, and dealers will inspect the headlamps and, if necessary, replace them, free of charge. The recall began October 30, 2020. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2020 X6 sDrive40i, xDrive40i, X6 M50i and X6M vehicles. The rear spoiler may not be appropriately bonded to its mounting plate.
Solución: BMW will notify owners, and dealers will inspect the rear spoiler on the affected vehicles and replace them , if necessary, free of charge. The recall began October 14, 2020. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2020 X6 sDrive40i, X6 xDrive40i, and X6 xDrive50i vehicles. The rear spoiler may detach.
Solución: BMW will notify owners, and dealers will inspect and replace the rear spoiler, as necessary, free of charge. The recall began April 16, 2020. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2018 540d, 2018-2020 530i, 530i xDrive, 540i, 540i xDrive, M550i xDrive, M5, 530e, 530e xDrive, X3 sDrive, X3 xDrive, X3 M40i, X3 M, and 2019-2020 X4 xDrive, X4 M40i, X4 M, X7 xDrive, X7 M50i, 740Li, 740Li xDrive, 750Li, 750Li xDrive, 8 Series Convertible and Coupe 840i, 840i xDrive, M850i xDrive, X5 sDrive, X5 xDrive, X5 M50i, X6 xDrive, X6 M50i, 330i, 330i xDrive, M340i, M340i xDrive, Z4 sDrive, Z4 M40i, 740Le xDrive and 745Le xDrive, 2018-2019 640i xDrive Gran Turismo and Rolls-Royce Phantom, 2019 M850i xDrive Gran Coupe and Rolls-Royce Cullinan and 2020 Toyota Supra vehicles. The back-up camera and display settings can be adjusted such that the rear view image is no longer visible and the system will retain that setting the next time the vehicle is placed in reverse. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 111, "Rearview Mirrors."
Solución: BMW will notify owners, and dealers will update the back-up camera software, free of charge. The recall began November 8, 2019. Owners may contact BMW customer service at 1-800-525-7417 or Rolls-Royce at 1-877-877-3735. Toyota owners may contact Toyota customer service at 1-888-270-9371.
Publicadas por año del modelo, no por VIN: pueden no afectar a este vehículo o ya estar resueltas. Confírmalo con un concesionario.
Water may come into contact with the starter relay and gradually cause corrosion. This could affect the electrical connection inside the relay and make the engine difficult to start. It may also result in a short circuit and could cause the starter to overheat leading to a fire when the vehicle is in motion or when it is parked with the ignition off. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The engine starter’s electrical contacts may overheat and cause the vehicle to start improperly. Continued starting attempts can intensify the overheating and ignite surrounding components, potentially leading to a vehicle fire while driving or shortly after parking. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The RSW22 starter with reinforced water tightness (RWT) may experience increased abrasion of the magnetic contact, causing deposits to build up at the lowest point inside the relay. These deposits may increase relay contact resistance, leading to starting failures or short circuits. If a short circuit occurs, either when attempting to start the vehicle or while driving due to vibration-related movement of the deposits, it could cause a thermal event and increase the risk of fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The failure concerns the RSW22 starter, type RWT (reinforced for watertightness). Increased abrasion of the magnetic contact can lead to the formation of deposits at the lowest point of the relay interior. This in turn can increase the resistance of the relay contact, causing accidental ignition or even short circuits, possibly leading to a thermal reaction and fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The hollow shaft of the servomotor was not welded correctly. The weld may not be able to withstand high braking pressure build-up and may break. In this case, the reduced braking performance requires greater force and the braking distance may increase. In addition, the ABS and DSC brake control systems are not assisted. This increases the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The software-based overload protection function cannot sufficiently prevent the starter being overloaded in the event of repeated long start-up attempts. The starter may overheat or sparks may be produced as a result of an increased current flow. This increases the risk of a fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The gas generator in knee airbag modules was not properly inserted into the air cushion, resulting in the cushion failing to unfold sufficiently. As a result, it may not be able to deploy correctly in the event of an accident, leading to a reduction in the restraint effect, increasing the risk of injury to the occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The integrated braking system could be compromised, which could lead to an unexpected failure of the hydraulic braking assistance, thereby requiring greater pressure on the brake pedal. This can result in a longer braking distance, as well as failure of the Anti-lock Braking System (ABS) and the Dynamic Stability Control (DSC), increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The dashboard in the affected vehicles may not have been manufactured to the manufacturer specifications. In the event of anaccident, the passenger side airbag may not deploy as intended which could increase the risk of injury to the frontpassenger. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Due to a manufacturing error, the weld seam of the integrated transmission control unit (ITCU) may not have been correctly executed. As a result, transmission oil could leak into the ITCU, causing it to fail. This may lead to transmission seizure, increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Emparejadas por marca y nombre de modelo: Safety Gate no publica el VIN. Comprueba las fechas de fabricación y facilita el código de la llamada al concesionario.