2002 BMW X5
3 recalls and 116 owner complaints on record for this model year.
Check a specific vehicle
This page describes the model. To see how one particular car is equipped, and whether its identifier is valid, decode its VIN.
Decode a VIN3 recalls and 116 owner complaints on record for this model year.
This page describes the model. To see how one particular car is equipped, and whether its identifier is valid, decode its VIN.
Decode a VINAlmost all of this describes the model year, not the individual car. Nothing here can tell you about this vehicle’s mileage, accidents or ownership — no identifier encodes those.
1 recall carries a do-not-drive or park-outside warning. Check whether this vehicle was remedied before driving or storing it.
BMW of North America, LLC (BMW) is recalling certain 2000-2002 BMW 320i, 323i, 325i, 325xi, 330i, 330xi, 323Ci, 325Ci, 330Ci, M3, 323iT, 325iT and 325xiT vehicles, 2001-2002 525i, 530i, 540i, M5, 525iT and 540iT vehicles, and 2001-2003 X5 3.0i, X5 4.4i, and X5 4.6is vehicles. These vehicles may have had a driver-side air bag module installed as replacement equipment such as after a vehicle crash necessitating replacement of the original air bag, or as a remedy part for a prior recall. These replacement modules contain an air bag inflator that may rupture due to propellant degradation occurring after long-term exposure to lower absolute humidity, temperature and temperature cycling.
Remedy: Owners are advised not to drive their vehicles until the vehicle has been remedied. BMW will notify owners, and dealers will inspect the driver side air bag module, replacing it as necessary, free of charge. The recall began March 15, 2017. Owners may contact BMW customer service at 1-800-525-7417.
ON CERTAIN PASSENGER VEHICLES, THE CONNECTION OF THE SAFETY BELT BUCKLE TO THE STEEL ROPE OF THE TENSIONER DOES NOT MEET BMW SPECIFICATIONS. IN SEVERE FRONTAL CRASHES, THIS CONNECTION CAN DETACH.
Remedy: DEALERS WILL INSPECT BOTH FRONT SAFETY BELT TENSIONER AND BUCKLE ASSEMBLIES, AND IF NECESSARY, REPLACE THESE PARTS. OWNER NOTIFICATION BEGAN MARCH 19, 2003. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT BMW AT 1-800-831-1117.
ON CERTAIN SPORT UTILITY VEHICLES, IT MAY BE POSSIBLE FOR THE FRONT BRAKE LINE TO SLIP OUT OF THE RETAINING BRACKET LOCATED AT THE FRONT STRUT. THE BRAKE HOSE THAT IS ATTACHED TO THE BRAKE LINE COULD COME IN CONTACT WITH THE TIRE AND BE SUBJECTED TO WEAR AND ABRASION.
Remedy: DEALERS WILL INSTALL AN ADDITIONAL RETAINING CLIP TO FURTHER SECURE THE BRAKE LINE TO THE FRONT STRUT. ADDITIONALLY, IF INSPECTION OF ANY BRAKE HOSE INDICATES THAT IT HAS EXPERIENCED DAMAGE, THE HOSE WILL BE REPLACED. OWNER NOTIFICATION BEGAN FEBRUARY 14, 2003. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT BMW AT 1-800-831-1117.
Published by model year, not by VIN — may not apply to this vehicle, or may already have been done. Confirm with a dealer.
Water may come into contact with the starter relay and gradually cause corrosion. This could affect the electrical connection inside the relay and make the engine difficult to start. It may also result in a short circuit and could cause the starter to overheat leading to a fire when the vehicle is in motion or when it is parked with the ignition off. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The engine starter’s electrical contacts may overheat and cause the vehicle to start improperly. Continued starting attempts can intensify the overheating and ignite surrounding components, potentially leading to a vehicle fire while driving or shortly after parking. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The RSW22 starter with reinforced water tightness (RWT) may experience increased abrasion of the magnetic contact, causing deposits to build up at the lowest point inside the relay. These deposits may increase relay contact resistance, leading to starting failures or short circuits. If a short circuit occurs, either when attempting to start the vehicle or while driving due to vibration-related movement of the deposits, it could cause a thermal event and increase the risk of fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The positive battery cable of the starter-generator may not have been manufactured correctly. This could result in a loose electrical connection, leading to excessive contact resistance. The vehicle cannot charge or start. Contact points in the starter-generator could overheat and cause a vehicle fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The chemical substances in the inflators of the TAKATA PSDI4 airbags may deteriorate over time, particularly in warm, humid climates. This could cause the airbag to rupture with too much force in the event of an accident, which could lead to serious or even fatal injuries in the worst-case scenario. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The failure concerns the RSW22 starter, type RWT (reinforced for watertightness). Increased abrasion of the magnetic contact can lead to the formation of deposits at the lowest point of the relay interior. This in turn can increase the resistance of the relay contact, causing accidental ignition or even short circuits, possibly leading to a thermal reaction and fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The failure concerns the RSW22 starter, type RWT (reinforced for watertightness). Increased abrasion of the magnetic contact can lead to the formation of deposits at the lowest point of the relay interior. This in turn can increase the resistance of the relay contact, causing accidental ignition or even short circuits, possibly leading to a thermal reaction and fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The hollow shaft of the servomotor was not welded correctly. The weld may not be able to withstand high braking pressure build-up and may break. In this case, the reduced braking performance requires greater force and the braking distance may increase. In addition, the ABS and DSC brake control systems are not assisted. This increases the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The software-based overload protection function cannot sufficiently prevent the starter being overloaded in the event of repeated long start-up attempts. The starter may overheat or sparks may be produced as a result of an increased current flow. This increases the risk of a fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The gas generator in knee airbag modules was not properly inserted into the air cushion, resulting in the cushion failing to unfold sufficiently. As a result, it may not be able to deploy correctly in the event of an accident, leading to a reduction in the restraint effect, increasing the risk of injury to the occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
A seam on the inflator housing of the driver airbag may not have been correctly welded. In case of accident, when the airbag is deployed, the inflator can burst, releasing metal parts which could cause injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The stated maximum load specified in the user manual is incorrect. This could cause users to overload the vehicle, potentially leading to damage to the car and an increased risk of accidents and injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The integrated braking system could be compromised, which could lead to an unexpected failure of the hydraulic braking assistance, thereby requiring greater pressure on the brake pedal. This can result in a longer braking distance, as well as failure of the Anti-lock Braking System (ABS) and the Dynamic Stability Control (DSC), increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The dashboard in the affected vehicles may not have been manufactured to the manufacturer specifications. In the event of anaccident, the passenger side airbag may not deploy as intended which could increase the risk of injury to the frontpassenger. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Due to a manufacturing error, the weld seam of the integrated transmission control unit (ITCU) may not have been correctly executed. As a result, transmission oil could leak into the ITCU, causing it to fail. This may lead to transmission seizure, increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Matched on brand and model name — Safety Gate publishes no VIN. Check the production dates, and quote the recall code to a dealer.
THE VEHICLE HAD A VERY DANGEROUS BLIND SPOT, AS A RESULT A 2 YEAR OLD CHILD WAS KILLED. CONSUMER FELT THERE SHOULD HAVE BEEN SOME TYPE OF SENSOR OR CAMERA IN THE REAR OF THE VEHICLE.*JB
ON 2/11/08 COLD DAY VEHICLE FAILED TO START SHOWING SAME SIGNS AS RECALLS ON 2004 AND 2007 MODELS THAT ARE RECALLS. VEHICLE SENT TO SHOP RETURNED 2 DAYS LATER WHILE TRAVELING ON MAJOR EXPRESSWAY VEHICLE STALLS OUT WITH OUT ANY ADVANCE WARNING AS IN 2004 AND 2007 MODELS SENT BACK TO SHOP VEHICLES OIL AND COOLANT MIXING CAUSING TOTAL ENGINE FAILURE. BMW'S RESPONSE NOT A RECALL FOR THIS YEAR BUT AWARE OF PROBLEM. *TR
OVER THE YEARS AFTER PURCHASING MY 2002 BMW X5, I HAVE REPORTED TO THE SERVICE DEPARTMENT OF WEATHERFORD BMW THAT THE TRANSMISSION WOULD NOT SHIFT GEARS PROPERLY AND THAT THE ENGINE WOULD ALL OF A SUDDEN START REVVING UP. AS THIS IS HAPPENING, THE ENGINE WOULD SURGE AND BUCK AT THE SAME TIME. EVEN THOUGH, I AND MY WIFE HAVE BEEN AWARE OF THESE ISSUES, THE SERVICE DEPARTMENT WAS NOT BEEN ABLE TO DUPLICATE THE SCENARIO OR EXPERIENCED THESE PROBLEMS WHILE SERVICING MY VEHICLE. WHILE DRIVING THE X5, NOT ONLY ME, BUT ALSO MY WIFE, SHE WOULD INFORM ME THAT THE ENGINE WOULD BUCK AND SURGE WHILE SHE WAS DRIVING THE VEHICLE. I BELIEVE THAT BECAUSE OF THESE ISSUES WITH THE TRANSMISSION AND THE ENGINE, THAT MY VEHICLE, A 2002 BMW X5 IS AN ACCIDENT WAITING TO HAPPEN. WITH THIS ALL SAID AND DONE, I WAS INVOLVED IN A HORRIBLE ACCIDENT WHERE THE VEHICLE IS NOW TOTALED, BUT I WAS ABLE TO WALK AWAY WITH ACHES AND PAIN (PHYSICALLY AND MENTALLY). I DO BELIEVE THAT BECAUSE OF THE PROBLEMS I HAD WITH THE TRANSMISSION AND ENGINE, IT WAS A DIRECT CAUSE OF THE ACCIDENT AND THAT BMW SHOULD REIMBURSE ME FOR THE 2005 BMW X5 THAT I JUST PURCHASED TO REPLACE MY PREVIOUS X5. ALSO, IN QUIZZING THE SALES MANAGER AT THE DEALERSHIP WHERE I PURCHASED MY NEW X5, I ASKED IF THERE WERE ANY MAJOR CHANGES TO THE VEHICLE. HIS REPLY WAS THAT DUE TO TRANSMISSION PROBLEMS WITH THE X5 - BMW CHANGED THE TRANSMISSION. THEREFORE, SINCE BMW WAS AWARE OF THESE ISSUES, AGAIN, I BELIEVE THAT BMW SHOULD REIMBURSE ME THE TOTAL PURCHASE PRICE OF MY 2005 X5. IF YOU HAVE ANY QUESTIONS, PLEASE CONTACT ME AT [XXX].*AK INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6). *TR
CAR WAS PARKED. I TRIED TO UNLOCK MY CAR WITH THE KEY FOB AND NOTHING HAPPENED. I UNLOCKED THE DOOR WITH THE KEY AND AFTER GETTING IN THE CENTRAL LOCKING SYSTEM WOULD NOT WORK. AFTER RESEARCHING THE PROBLEM I FOUND THAT THE GMIII CONTROLS THE CENTRAL LOCKING AS WELL AS OTHER ITEMS LIKE THE WINDSHIELD WIPERS, INTERIOR LIGHTS, SUN ROOF, AND REAR UPPER AND LOWER HATCH. I ORDERS A NEW ONE AND WHEN I TOOK THE OLD ONE OUT TO REPLACE IT I FOUND THAT IT HAD CAUGHT ON FIRE AND BLEW FUSE 14. IT APPEARS A THYRISTOR OR TIAC GOT TO HOT AND SET THE BOARD AND CASE ON FIRE. I HAD SMELT A PLASTIC SMELL EARLIER WHILE DRIVING SO IT MAY HAVE BEEN BURNING BEFORE I PARKED. I AM ATTACHING PHOTOS.
THE DASHBOARD WENT DARK, ONLY GAUGE THAT WORKED WAS THE TACHOMETER WHICH I COULDNT SEE BECAUSE I HAD NO DASHBOARD LIGHTS. STOPPED VEHICLE AND TOOK THE KEYS OUT COULDNT TURN MY LIGHTS OFF HAD NO TURN SIGNALS,THE 3RD BRAKE LIGHT WAS ON ALL NIGHT LONG KILLING THE BATTERY I TRIED EVERY FUSE. ALSO MY HEADLIGHTS WOULDNT TURN OFF THE LIGHTING CONTROLS WERE USELESS, AND JUST KEPT SMELLING AN ELECTRONIC BURNING SMELL. I MANAGED TO DISCONNECT ALL THE LIGHTS EXCEPT THE 3RD BRAKE LIGHT. COULDNT DISCONNECT THE BATTERY BECAUSE THE LIFT GATE TO GET INTO THE BACK WOULDN'T WORK AND THE CENTER CONSOLE HAZARDS STUCK ON AND DOOR LOCKS DIDN'T WORK I HAD TO REMOVE THE GLOVE BOX AND ALL THE PANELING AND TRACK DOWN THE SMELL. TURNS OUT THE PROBLEM WITH THIS VEHICLE IS THAT THE RAIN MANAGES TO WORK ITSELF DOWN THE INSIDE OF THE A FRAME ON BOTH DRIVER AND PASSENGER SIDES OF THE VEHICLE ON DRIVER SIDE IT DESTROYS THE OBD MODULE BUT ON THE PASSENGER SIDE IT TRICKLES DIRECTLY INTO THE LCM LIGHTING CONTROL MODULE WHICH COMPLETELY TAKES YOUR EYES OFF THE ROAD WHEN YOU CANT SEE THE DASHBOARD YOUR HEADLIGHTS START STROBING ON AND OFF AND THEN HALF GET STUCK ON AND HALF JUST DONT WORK BUT WHEN YOU SPEND THE HOURS GETTING TO THE LCM TO FIND OUT IT HAS MELTED RIGHT INTO THE SIDE OF YOUR VEHICLE AND YOU CAN TELL IT WAS ON FIRE !! AND THIS HAS HAPPENED TO NUMEROUS PEOPLE ON THE BMW FORUMS IM JUST HAPPY MY 3 YEAR OLD SON WASN'T WITH ME. AND THE REAL KICKER IS THAT I HAVE NO VEHICLE NOW AND IT COST 600$ FOR A NEW LCM THAT HAS TO BE PROGRAMMED TO YOUR VEHICLE WHICH WILL COST ANOTHER 300$ WHEN I COULD HAVE HURT SOMEONE ELSE OR MYSELF WHEN YOU CANT SEE BUT YOU CAN SMELL SOMETHINGS BURNING ITS A HAZARD TO EVERYONE ON AND OFF THE ROAD .
I HAVE A 2002 525I WHICH I DROVE TO WORK ON JANUARY 15, 2019. AFTER BEING IN WORK FOR 15 MINUTES, I WAS NOTIFIED THAT THE ENTIRE FRONT END OF MY CAR WAS ENGULFED IN FLAMES. THE TOP OF THE HOOD, UNDER THE HOOD, AND UNDER THE FRONT END OF MY CAR WAS COMPLETELY ON FIRE. I HAVE READ ABOUT THE PVC RECALL FOR 2007-2011, BUT I ALSO READ "BMW HAD LOOKED INTO HEAT DAMAGE INVOLVING THE HEATING AND COOLING SYSTEM AS EARLY AS 2007 BUT STEPPED UP ITS ANALYSIS WORK IN SEPTEMBER." THAT WAS FROM A CHRONOLOGY REPORT PROVIDED BY BMW TO NHTSA, AND QUOTED FROM ABCNEWS.GO.COM. WHAT THIS TELLS ME IS BMW DIDN'T LOOK BACK ANY EARLIER THAN 2007. IT WAS TERRIFYING, AND THANK GOD NO ONE WAS HURT. WHAT IS BMW DOING ABOUT THIS? AND WHAT IS MY NEXT COURSE OF ACTION?
VEHICLE FIRE WAS PARKED FOR A COUPLE OF DAYS AND OWNER WENT TO CAR AND NOTICE THAT THE INTERIOR OF THE VEHICLE HAD A PAST TENSE FIRE. THE AIRBAGS WERE DEPLOYED EXPECT FOR THE ONE ON THE PASSENGER SIDE DOOR. NO EXTERIOR DAMAGE NOTED TO THE VEHICLE OR IN THE ENGINE COMPARTMENT. THE FIRE ORIGIN WAS ON THE PASSENGER SIDE DASHBOARD BEHIND THE GLOVE COMPARTMENT AND AIRBAG, PLEASE CONTACT SIOUX CITY FIRE RESCUE FOR FURTHER INFORMATION.
AS MY WIFE AND I DRIVING TO HER MD APPOINTMENT ON 11/26/12. I'VE NOTICED GAS SMELL INSIDE THE CAR,AND CAR SUDDENLY LOSING POWER, WHEN I'VE STEP ON THE GAS PEDAL. IT'S LIKE GAINING POWER TO GO AND SUDDENLY LOSES POWER. I WAS KIND OF CONFUSED WHAT HAPPENED . WE WERE ON THE ROAD RIGHT BEHIND THE INTERSECTION. WE HAD TO STOP FOR THE RED LIGHT,WHEN I'VE TRIED TO GO, THE CAR WAS NOT MOVING LIKE IT SHOULD. WE MADE IT TO THE OTHER SIDE OF THE INTERSECTION, WHICH THERE IS DENNY'S RESTAURANT PARKING LOT. BY THE TIME I'VE PULLED OVER TO SEE WHAT IS GOING ON,WE WERE STILL IN THE CAR. ALL OF THE SUDDEN THERE WAS A LOUD SOUND, LIKE EXPLOSION UNDER THE HOOD OF THE CAR AND FIRE STARTED.THANKS GOD, WE GOT OUT OF THE CAR JUST IN TIME. THE FIRE WAS BURNING OUT OF CONTROL. COUPLE OF PASSERBY HAD FIRE EXTINGUISHERS IN THEIR CARS,TRIED TO PUT THE FIRE OUT, WHILE I WAS ON THE 911 CALL,BUT NO LUCK. IN JUST A LESS THAN A MINUTE THE WHOLE CAR WAS ENGULFED IN FLAMES. IT TOOK FIRE DEPT LIKE 20-30 MINUTES TO PUT THE FIRE OUT,AND MY CAR JUST MELTED FRONT OF MY EYES. *TR
TL* THE CONTACT OWNS A 2002 BMW X5. WHILE DRIVING APPROXIMATELY 45 MPH, THE VEHICLE SUDDENLY STALLED AND SMOKE WAS EMITTING FROM UNDER THE HOOD. THE VEHICLE WAS TOWED TO THE DEALER FOR DIAGNOSTIC TESTING WHERE THE TECHNICIANS STATED THAT THE OIL SEPARATOR WAS FROZEN. THE VEHICLE WAS NOT REPAIRED. THE VIN WAS UNAVAILABLE. THE APPROXIMATE FAILURE MILEAGE WAS 105,000.
BMW X5 2002. CAR SITTING IN DRIVEWAY OVERNIGHT ACTIVATED 5 OF 6 AIRBAGS. WINDSHIELD BROKE AND DASHBOARD SHOW FIRE DAMAGE.
MY SON WAS DRIVING MY 2002 BMW X5 SUV FOR APPROXIMATELY 30 MINUTES (MOSTLY HIGHWAY) WHEN THE "FAIL SAFE" LIGHT CAME ON. HE BEGAN TO PULL INTO THE BREAKDOWN LANE WHEN THE CAR STALLED AND "SYSTEM FAILURE" LIGHT CAME ON. WHEN HE GOT OUT OF THE CAR, THERE WERE FLAMES SHOOTING OUT FROM BENEATH THE ENGINE ON THE PASSENGER SIDE. HE AND HIS FIANCE QUICKLY RAN DOWN THE ROAD AND THE CAR WAS FULLY ENGULFED IN FLAMES WITH BLACK SMOKE FILLING THE SKY WITHIN MOMENTS. THE CAR IS TOTALED WITH ALL WINDOWS MELTED AS WELL AS THE ENTIRE ENGINE COMPARTMENT. BOTH FRONT TIRES EXPLODED. I HAVE GONE ONLINE AND THERE ARE MANY X5'S THAT HAVE SPONTANEOUSLY CAUGHT ON FIRE FOR NO APPARENT REASON. *TR
DRIVING AT 50 MPH I WAS BEING HARASSED BY ANOTHER MOTORIST BECAUSE I WAS DRIVING THE SPEED LIMIT. I DECIDED TO LET HIM PASS BUT FIRST I HAD TO SPEED UP TO 58 MPH INORDER TO COMPLETELY OVERTAKE A PASSENGER CAR TO MY RIGHT (PASSENGER SIDE) I GAVE THE THROTTLE SOME GAS AND THE CAR WENT NOWHERE. THE NEEDLE WENT ALL THE WAY INTO THE RED ZONE ON THE TACHOMETER. THE DRIVER BEHIND ME (ANOTHER BMW 3 SERIES),TAILGATED ME. IT SCARED ME SO BAD, THAT I DID NOT SEE A DEEP POT HOLE IN THE ROAD SURFACE. I HIT IT SO HARD, THAT I SPUN AROUND AND ALL OF MY WHEELS WERE DAMAGED. I HAD ALL FOUR WHEELS REPAIRED AND TIRES AT A COST OF $2000.THE DAY BEFORE, I NOTICED THE SERVICE ENGINE SOON LIGHT WAS ON. OF COURSE, I WANT THIS CHECKED OUT.SO I SCANNED THE CAR. IT WAS DISPLAYING 000030 BMW/ OR FOR/ P CODE P0741 " TORQUE CONVERTER CLUTCH VALVE STUCK OFF .SO I WENT TO A BMW DEALER. EXPLAINED EVERYTHING. THEY SHOW ME THE CODES PULLED FROM THE CAR. THE CODE FOR THE TC CLUTCH VALVE NOT WORKING WAS SHOWN.(THEIR EQUIVALENT TO P0741) THEY TELL ME IT IS THE DISA VALVE.???? IS BMW TRYING TO COVER THIS UP?.DISA HAS ZERO TO DO WITH THE TORQUE CONVERTER. I SEE HOW MANY HAVE FAILED AND BMW DOES NOTHING? I COULD HAVE BEEN KILLED. THE CAR DID NOT RESPOND WITH MY REQUEST IN A MANNER THAT AFFECTED MY WELL BEING. IF THIS PROBLEM IS INVOLVED WITH MANY, MANY CLAIMS BECAUSE OF A PART THAT IS PROVEN TO BE DEFICIENT AS IT SOUNDS, I AM SURE IF INVESTIGATED YOU WILL FIND SOME INJURIES AND/OR DAMAGES AND DEATHS HAVE OCCURRED AND WHEN THE DEALER SEES A BAD ONE, THEY TRY TO BILL IT OUT AS SOMETHING ELSE. I CAN NOT BE THE ONLY ONE. AND WHY DID THE BMW DEALER TRY TO RIP ME OFF? I LIKE MY CAR BUT THE LETTERS BMW PUT A BAD TASTE IN MY MOUTH. RIGHT DOWN TO THE JERK WHO TRIED TO RUN ME OFF OF THE ROAD. BMW= ? ANYONE ELSE? ANYONE WHO WAS TOLD SOMETHING ELSE WAS BAD WHEN IT IS A BAD SEAL INSIDE THE TORQUE CONVERTER? *TR
I GOT INTO A AUTOMOBILE ACCIDENT ON MONDAY OCT 19, 2009. I WAS DRIVING MY 2002 BMW X5. SOMEONE DRIVING AROUND 50MPH HIT MY X5 REAR IMPACT TO DRIVERS SIDE. THEN I BELIEVE IT DRAGGED ALONG THE DRIVERS SIDE. THE AXLES BROKE, TIRE WENT TO THE HIGHWAY, THE CAR WAS BENT IN A WAY THAT THE ROOF WAS POINTING UPWARDS IN THE MIDDLE. THE IMPACT WAS SO GREAT THAT MY CAR (X5) IS CONSIDERED TOTALED. THE ISSUE I HAVE IS THAT MY CAR SHOULD BE EQUIPPED WITH MANY AIRBAGS. HOWEVER, NON OF THE AIRBAGS OPENED TO PROTECT ME. *TR
DUE TO FLOOR MAT HAVING MOVEMENT MAT SLID AGAINST GAS PEDAL. OWNER WAS IN REVERSE AND ACCELERATED BACKWARDS INTO A CONCRETE GARAGE. GAS PEDAL ISHAS BEEN ATTACHED AT THE FLOOR. PLEASE DESCRIBE DETAILS. *AK
Bmw has failed on several occasions to address this issue or service vehicle. I have made them aware of the situation but continue to receive letters that indicate I could die of the airbag.
Filed by owners of this model year and unverified by NHTSA — one person’s account, not an established fact.